ToolKitRc M8P

Contents

ToolkitRC M8P Intelligent Charger User Manual

Model: M8P | Brand: ToolkitRC

1. Introduction

Thank you for purchasing the M8P balance charger. Please read this manual carefully before use to ensure proper operation and safety.

The M8P is a multifunctional tool that integrates functions such as a balance charger and discharger, a signal measuring device, and a signal source.

For further information and firmware updates, please visit the official ToolkitRC website: www.toolkitrc.com. A detailed user manual in PDF format is also available for download on the product page.

ToolkitRC M8P charger and packaging

Figure 1: ToolkitRC M8P Charger and Packaging

2. Safety Information

⚠ Please mind potential fire risk and strictly follow the instruction manual for charging and storage.

  • Input Voltage: The M8P allows an input voltage of DC 7.0-35.0V. Ensure the charger is only connected to a suitable power source with correct polarity.
  • Environment: Do not use this product in hot, humid, flammable, or explosive environments.
  • Supervision: Do not use this charger without supervision. Never leave charging batteries unattended.
  • Power Disconnection: When not using this product, please unplug the input power.
  • Charging Current: When using the charging function, please set a current that matches the battery. Do not set an excessive current for charging to avoid damage to the battery. Check the guidelines of your battery's manufacturer for correct charging instructions.
  • Battery Compatibility: Ensure the correct battery type has been selected prior to charging. An incorrect choice may damage the battery and/or become a fire hazard. Please proceed with caution. Do not use this product to charge non-compatible battery chemistries.

3. Product Overview

The M8P charger features a compact design with a clear display and intuitive controls.

3.1. Key Features

  • Battery Compatibility: Charges, discharges, and balances LiPo, LiHV, LiFe, Lion, LTO (1-8S), NiMh (1-20S), PB (1-10S) batteries.
  • Charge/Discharge Power: Max 20A @ 600W charge current. Recycle/External discharge mode Max 20A @ 600W. Internal discharge mode Max 3A @ 20W.
  • Adjustable Cut-off Voltage: Lithium battery cut-off voltage can be adjusted (TVC function).
  • Battery Analysis: Measures battery voltage, internal resistance, and automatically balances lithium packs.
  • Signal Measurement/Output: Measures/outputs PWM/PPM/SBUS standard signals with 1 microsecond accuracy.
  • Power Supply Function: Constant current and constant voltage source output (1-35V constant voltage, 0.5-20A constant current).
  • Drone Battery Support: Can be adapted for charging consumer-grade drone batteries.
  • User Interface: Multi-language user interface.
  • Firmware Upgrade: Easily upgradable via USB.

3.2. M8P Layout

M8P Front Layout Diagram

Figure 2: M8P Front Layout. Key components include the Display, Output port, Balance port, Signal port, Scroll wheel, and Exit button.

M8P Back Layout Diagram

Figure 3: M8P Back Layout. Key components include the USB A output, Input port (DC 7-35V), and Cooling fan.

4. Setup

4.1. Quick Start

  1. Connect a 7-35V power supply to the input port on the back of the M8P.
  2. The display will show the boot logo for 2 seconds, accompanied by a welcome sound.
  3. After booting, the screen enters the main interface, displaying current voltage, power, temperature, and cell information.
  4. Press and hold [Exit] to enter the auxiliary function interface.
  5. Scroll the [Scroll Wheel] to switch between pages.
  6. With the charger idle, short press the [Scroll Wheel] to set charging parameters. During charging, short press to adjust amperage or stop the process.
  7. With the charger idle, press and hold [Scroll Wheel] to enter the system setting interface.
  8. Short press [Exit] to return to the previous interface.
M8P Main Interface

Figure 4: M8P Main Interface showing battery voltage and cell readings.

4.2. Battery Type Setting

From the main interface, short press the [Scroll Wheel] to enter the charging function. Select 'Battery selection' in system settings. Scroll the [Scroll Wheel] to select a preset battery type or create a new one (up to 32 battery files). Short press the [Scroll Wheel] to enter specific battery settings.

M8P Battery Type Selection Screen

Figure 5: Battery Type Selection. Move the cursor and short press the scroll wheel to modify.

The charger supports charging and discharging of 6 types of batteries: LiPo, LiHV, LiFe, Lion, LTO, NiMh, and PB. There is also a smart battery mode.

Glossary of Battery Terms:

  • LiPo: Lithium polymer battery, nominal 3.70V, fully charged 4.20V.
  • LiHV: High-voltage lithium battery, nominal 3.85V, fully charged 4.35V.
  • LiFe: Iron-lithium battery, nominal 3.30V, fully charged 3.60V.
  • Lion: Lithium-ion battery, nominal 3.60V, fully charged 4.10V.
  • LTO: Lithium-ion battery, nominal 2.40V, fully charged 2.70V.
  • NiMh: Nickel-metal hydride battery, nominal 1.20V.
  • PB: Lead-acid battery, nominal 2.00V.

4.3. Cell Setting

Move the cursor to [Battery Section] and short press the [Scroll Wheel] to modify the number of cells (1S to 8S). Rotate the [Scroll Wheel] to adjust the value.

M8P Cell Setting Screen

Figure 6: Cell Setting. Options for 1S to 5S shown.

Tips:

  • If set to [Auto], the charger automatically identifies the number of cells by checking the total voltage against the balance port data.
  • If the connected battery is over-discharged or over-charged, this may cause an incorrect cell-count. Adjust manually if needed.
  • An incorrect cell count can lead to overcharging and fire risk.
  • Cell count is more accurately determined if the balance port is connected.

4.4. Work Mode

Move the cursor to [Mode] and short press the [Scroll Wheel] to modify the work mode. Available modes are Charge, DisCHG (Discharge), and StoCHG (Storage Charge).

LiPo, LiHV, LiFe, Lion, LTO batteries can be charged, discharged, and stored. NiMh batteries can be charged, discharged, or cycled. PB batteries can be charged and discharged. Short press the [Scroll Wheel] and [Exit] to take effect.

4.5. Discharge Mode

Under discharge, storage, and cycle modes, the option of discharging the battery will appear. Move the cursor to [Discharge Mode] and short press the [Scroll Wheel] to modify the discharge mode.

M8P Discharge Mode Selection Screen

Figure 7: Discharge Mode Selection. Options include Inter (Internal), Recycle, and External.

  • Normal mode: Discharges using internal heat dissipation, max 3.0A@20W.
  • Recycle mode: When a battery is used as input, power is recovered to the input battery, max 20.0A@600W.
  • External mode: When the input port is connected to a discharge load and the output port is connected to the battery, it can be discharged through this function, max 20.0A@600W.

4.6. Max Input Voltage

When Recycle discharge mode is selected, the Max input voltage option appears. Move the cursor to [Max Input Vol.] and short press the [Scroll Wheel] to adjust. If the input voltage reaches this value during discharge, the discharge will stop.

M8P Max Input Voltage Setting Screen

Figure 8: Max Input Voltage Setting. Example values 27.8V, 27.9V, 28.0V.

Tips:

Set the Max input voltage to the highest protection voltage of your power supply. Setting a high overvoltage may damage the input power.

4.7. End Voltage Setting (TVC)

Move the cursor to [End Voltage] and short press the [Scroll Wheel] to modify the end voltage for individual cells. Rotate the [Scroll Wheel] to adjust the value (step 0.01V).

M8P End Voltage Setting Screen

Figure 9: End Voltage Setting. Example values 4.18V to 4.22V.

Notes:

  • Only LiPo, LiHV, LiFe batteries can set the cut-off voltage.
  • Do not modify the cut-off voltage if you are unfamiliar with the battery characteristics.
  • The charging cut-off voltage can be set to a range of plus or minus 50mV of the full voltage.
  • TVC: Terminal Voltage Control.

4.8. Current Setting

Move the cursor to [Charge Current] or [DisCHG Current] and short press the [Scroll Wheel] to modify the current. Rotate the [Scroll Wheel] to adjust (step 0.1A). Scroll quickly to increase or decrease. The charger supports up to 10.0A.

M8P Discharge Current Setting Screen

Figure 10: Discharge Current Setting. Example values 1.8A to 2.2A.

Tips:

  • Set the charging rate of 1-2C according to the battery capacity. For example, for a 2000mAh battery, set the charge current to 2.0-4.0A.
  • The charge/discharge current is only valid in the corresponding work mode.

4.9. NiMH Setting (PeakV)

When the battery type is NiMH, the peak voltage value when the battery is fully charged can be set. The range is 5mV-15mV.

M8P NiMH PeakV Setting Screen

Figure 11: NiMH PeakV Setting. Example values 5mv to 9mv.

Tips:

  • This function is only available on NiMH cells.
  • PeakV: The maximum voltage drop per cell when the nickel-metal hydride battery is fully charged.

4.10. Cycle Setting

When the battery type is NiMh and under cycle mode, the options for Cycle time and Rest time will appear. Move the cursor to [Cycle times] and short press the [Scroll Wheel] to set the range of cycle times to 2-12. The charger will follow the pattern: discharge->charge->discharge->charge....

M8P Cycle Times Setting Screen

Figure 12: Cycle Times Setting. Options for 2 to 6 cycles shown.

Move the cursor to [Rest time] and short press the [Scroll Wheel] to set the rest time of cycle charge. The range is 2 minutes to 10 minutes.

M8P Rest Time Setting Screen

Figure 13: Rest Time Setting. Options for 2Min to 6Min shown.

4.11. External Load Setting

When external discharge is selected as the discharge mode, the external load setting will appear. Set the wattage according to the external load used.

M8P External Load Setting Screen

Figure 14: External Load Setting. Example values 30W to 32W.

4.12. Smart Battery Setting (UAVbat)

When UAV battery is selected as the battery type, there are only two options for battery setting: drone type and Max current.

M8P UAV Battery Setting Screen

Figure 15: UAV Battery Setting. Shows Battery Type, Drone model, and Max Current.

Move the cursor to [Drone model] and short press the [Scroll Wheel] to select between different drone models (e.g., Mavic2 17.6V, MavicS 13.05V, Phantom 17.4V, Inspire 26.1V).

M8P Drone Model Selection Screen

Figure 16: Drone Model Selection. Example models shown.

Move the cursor to [Max Current] and short press the [Scroll Wheel] to set the charge current. The range is 0.5A to 20A.

5. Operating Instructions

5.1. Charge and Discharge Process

When charging and discharging starts, the charger enters the main interface. Rotate the [Scroll Wheel] on this interface to toggle between three different displays:

  • Display 1 (Main): Shows P1 (Power selection in system settings), Input voltage (e.g., 24.01V), Accumulated power consumption (e.g., 0.0Wh), Internal temperature (e.g., 45.0°C), Constant voltage sign (V), Constant current sign (C), Main port voltage (e.g., 24.01V), Main port current (e.g., 2.00A), Working time (e.g., 010:00), Charged capacity (e.g., 338mAh), Voltage for the first battery cell (e.g., 4.000V), Total voltage measured at balance lead (e.g., 24.00V), and indication for no battery connected (---V).
  • Display 2 (Internal Resistance): Shows internal resistance information for each cell and total internal resistance.
  • Display 3 (General Information): Shows current charging status, end voltage/charge current, and current charging power.
M8P Internal Resistance Display

Figure 17: M8P Internal Resistance Display showing individual cell resistance and total resistance.

M8P Charging Status Display

Figure 18: M8P Charging Status Display showing current charge, voltage/current, and power.

Short press the [Scroll Wheel] to dynamically set the charge current or stop charging. To end the process, move the cursor to [Stop] and short press the [Scroll Wheel].

When charging is complete or an error occurs, a popup will appear with an audible tone.

Tips for Charging/Discharging:

  • Never leave cells unattended during charging or discharging.
  • For lithium batteries, balancing only occurs if the balance plug is connected. The charger will automatically balance each cell if a balance plug is detected.
  • Charging will automatically start for the next battery if the initial battery is disconnected after being fully charged. If a set number of cells is set, ensure that the subsequent cell count matches the initial battery. If set to automatic, make sure the cell count matches what is detected.

5.2. Accessibility Functions

After selecting and long pressing [Exit] in the main interface, you can enter the auxiliary function interface, which includes:

  • Measure resistance
  • Measure signal
  • Signal output
  • ESC test
  • Power (Adjustable Power Supply)

5.2.1. Measure Signal

Move the cursor to [Measure signal] and short press the [Scroll Wheel] to enter the signal test interface. Scroll the [Scroll Wheel] to select the signal type (PWM, PPM, SBUS).

For PWM, the display shows pulse width (e.g., 1500us) and frequency (e.g., 20.0ms/50Hz).

For PPM, the display shows 8 channels with their respective pulse widths (e.g., 1500).

For SBUS, scroll to display channels 1-8, channels 9-16, and overall status (Channel DG1/DG2, Frame lost, Failsafe, Endbyte).

5.2.2. Signal Output

Move the cursor to [Signal Output] and short press the [Scroll Wheel] to enter the Signal Output interface. Scroll the [Scroll Wheel] to select the type of signal to be tested (PWM, PPM, SBUS).

PWM: Choose between Manual, Auto 1, Auto 2, and Auto 3. In manual mode, you can change pulse width (800-2200us) and cycle values (2.5ms/400Hz to 50.0ms/20Hz). Auto modes automatically change pulse width at different speeds.

PPM/SBUS: Scroll to the channel value to be modified. Short press the [Scroll Wheel] to modify the output pulse width value of that channel.

5.2.3. ESC Test

Select [ESC test] with the cursor, short press the [Scroll Wheel] to enter the ESC test mode. Scroll the [Scroll Wheel], move the cursor to pulse width/cycle, short press the [Scroll Wheel] to change the corresponding value.

M8P ESC Test Screen

Figure 19: M8P ESC Test Screen showing pulse width, frequency, voltage, and current.

5.2.4. Adjustable Power Supply

Select the adjustable power supply with the cursor, and short press the [Scroll Wheel] to enter. The voltage and current of the output power supply can be set. Move the cursor to start, short press the [Scroll Wheel] to start power output and return to the main interface.

M8P Adjustable Power Supply Screen

Figure 20: M8P Adjustable Power Supply Screen showing Output Voltage, Max Current, and Start option.

6. System Settings

After pressing and holding the [Scroll Wheel] in the main interface, you can enter the system setting interface. Short press to expand the settings.

6.1. Input Settings

  • Power select: Auto (P1, P2, P3 presets).
  • Power type: Choose between battery pack and adapter. For battery packs, recycle mode is enabled; for adapters, recycle mode is disabled.
  • Max power: Maximum wattage allowed via the input port during charging (e.g., 90W).
  • Max current: Maximum current allowed via the input port during charging (e.g., 12.0A).
  • Voltage range: Input voltage range (e.g., 7.0 - 24.0V).

6.2. Security Settings

  • Safe inter Temp.: Charging stops if device temperature exceeds this value (e.g., 70°C).
  • Safe Exter Temp.: Charging stops if environment temperature exceeds this value (e.g., 50°C).
  • Safe time: Maximum time limit for continuous charging/discharging (e.g., 200Min).
  • Safe capacity: Maximum accumulated capacity for a charging/discharging session (e.g., 20Ah).

6.3. Personalization

  • Backlight: Backlight brightness level (1-10).
  • Operation volume: Volume of the scroll wheel (Off, Low, Medium, High).
  • Announce volume: (Medium)
  • Warning volume: (High)
  • Language: System display language (English, Chinese, etc.).
  • Theme style: Light and Dark themes.

6.4. Other Settings

  • Battery selection: Option to show/hide frequently used parameters.
  • Work completed: Whether to stop or trickle charge after charging is complete.
  • Balance start Vol.: Balance cells prior to full current charge.
  • Continuous work: Enables/disables continuous charging/discharging after battery replacement.
  • Default: Reset factory settings.
  • ID: Independent ID for each device (e.g., FF3005D3 - V1.00).

7. Maintenance

7.1. Firmware Upgrade

Connect the M8P to a computer using the USB cable provided. The computer should recognize a USB drive named "Toolkit". Download the upgrade file (app.upg) from www.toolkitrc.com and overwrite the files in the USB drive to upgrade the firmware.

7.2. Fan Level

The cooling fan operates at half speed when the internal temperature exceeds 45°C to reduce noise. If the internal temperature exceeds 53°C, the fan turns on full-speed to enhance heat dissipation.

7.3. Manual Voltage Calibration

With the M8P powered off, press and hold the [Scroll Wheel]. Without releasing it, connect the power supply. The system will enter manual voltage calibration mode. Use a voltmeter to measure the actual voltage of each battery. Move the cursor to the corresponding voltage value and modify it to match the voltmeter value. After calibration, move the cursor to save, short press once, and the buzzer will beep once to confirm successful save. Exit or shut down after calibration.

7.4. Full Charge Mode

When a lithium battery is fully charged, the charger will prompt "Fast charge complete". If the battery is not removed, the charger will trickle charge until the battery is disconnected.

8. Troubleshooting

  • Charger not recognized by PC for firmware update: Ensure the USB cable is properly connected and try a different USB port or cable. Verify that the charger is in the correct mode for firmware updates as per the instructions. If the issue persists, consult the ToolkitRC website for specific driver information or troubleshooting guides.
  • Incorrect cell count detection: If the connected battery is severely over-discharged or over-charged, the automatic cell count detection might be inaccurate. Manually adjust the cell count in the settings. Always ensure the balance port is connected for accurate cell readings.
  • Charging/Discharging stops unexpectedly: Check the 'Safe inter Temp.', 'Safe Exter Temp.', 'Safe time', and 'Safe capacity' settings in the Security Settings. If any of these limits are reached, the charger will stop operation for safety.
  • Battery not balancing: For lithium batteries, ensure the balance port is securely connected to the charger. Balancing only occurs when the balance plug is detected.

9. User Tips

  • The M8P's storage mode is highly effective, automatically charging or discharging to reach the set per-cell voltage, which is useful for maintaining battery health.
  • Cell voltage readouts are generally consistent, keeping cells within a few millivolts, making it a reliable tool for diagnosing battery pack health.
  • Internal Resistance (mΩ/IR) readings are best used for relative comparison of battery health over time, rather than as absolute lab-grade values.
  • The fan control is designed to protect the unit and is generally sensible in operation.
  • The charger performs well across various cell counts, including 4S, 6S, and 7S batteries.

10. Specifications

Category Parameter Value
Charge Input 7-35V @ MAX 25A
Battery type LiPo, LiHV, LiFe, Lion, LTO (1-8S); NiMh (1-20S); Pb (1-10S)
Balance current 1000mA @ 4.2V
Accuracy <0.005V
Power 0.1-20A @ 600W
Discharge power 0.1-20A @ 600W (Rec/Ext Mode); 0.1-3A @ 20W (Internal Mode)
USB A Output 2.1A @ 5.0V (upgradable)
Measure Voltage 1.0V-5.0V @ 1-6S
Internal resistance 0.1mΩ-99Ω @ 1-8S
Signal Output PWM 880us-2200us @ 20-400Hz
PPM 880us-2200us * 8 CH @ 20-50Hz
SBUS 880us-2200us * 16 CH @ 20-100Hz
Power 1-20A @ 1-35V Mode: CC+CV
Product Display IPS 2.4 inch 320*240 resolution
Size 99mm * 72mm * 35mm
Weight 180g
Individual packing Size 125mm * 81mm * 41mm
Weight 250g

11. Warranty and Support

For warranty information, technical support, and service inquiries, please visit the official ToolkitRC website at www.toolkitrc.com or contact their customer service directly.

© 2023 ToolkitRC Technology (Shenzhen) Co., Ltd. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.