1. Introduction
The AD623 is an integrated, low-cost, high-accuracy instrumentation amplifier designed to deliver rail-to-rail output swing with supply voltages ranging from 3 V to 12 V. This module offers exceptional user flexibility, allowing gain programming with a single external resistor and conforming to the industry-standard 8-lead pinout configuration.
It is capable of unity gain (G=1) without an external resistor, and with an external resistor, it can be programmed for gains up to 1000. The AD623's superior accuracy is achieved through an increasing AC common-mode rejection ratio (CMRR) that improves with gain, effectively rejecting line noise harmonics up to 200 Hz. The module features a wide input common-mode range and can amplify signals with common-mode voltages as low as 150 mV below ground, ensuring robust performance with both dual and single polarity power supplies.
2. Key Features
- Easy to use
- Rail-to-rail output swing
- Input voltage range extends 150 mV below ground (single supply)
- Low power consumption: 550 µA maximum supply current
- Gain set with one external resistor
- Wide gain range: 1 to 1000
- High accuracy DC performance: 0.10% gain accuracy (G = 1), 0.35% gain accuracy (G > 1)
- Low noise: 35 nV/√Hz RTI noise at 1 kHz
- Excellent dynamic specifications
- 800 kHz bandwidth (G = 1)
- Fast settling time: 20 µs to 0.01% (G = 10)
3. Applications
- Low power medical instrumentation
- Transducer interfaces
- Thermocouple amplifiers
- Industrial process controls
- Difference amplifiers
- Low power data acquisition systems
4. Package Contents
The package includes:
- 1 x AD623 Programmable Gain Instrumentation Amplifier Module
- Header pins for connection

5. Setup and Connections
The AD623 module requires careful connection of power, input, and output signals. Refer to the pinout diagram below for proper wiring.

5.1 Pinout Description
| Pin Label | Description |
|---|---|
| +US | Positive Power Supply (3V to 12V) |
| -US | Negative Power Supply (for dual supply operation) or Ground (for single supply) |
| IN+ | Non-inverting Input |
| IN- | Inverting Input |
| OUT | Amplifier Output |
| REF | Reference Input (typically connected to ground for single-ended output) |
| GND | Ground Connection |
| RG | Gain Resistor Pins (connect an external resistor between these pins to set gain) |
5.2 Power Supply
The AD623 can operate with either a single or dual power supply:
- Single Supply: Connect +US to your positive supply (3V to 12V) and -US to GND.
- Dual Supply: Connect +US to your positive supply and -US to your negative supply. Ensure both supplies are within the 3V to 12V range (e.g., +5V and -5V).
5.3 Input Connections
Connect your differential input signal to the IN+ and IN- pins. The AD623 is designed for differential signal amplification.
5.4 Output Connection
The amplified signal will be available at the OUT pin. The output is rail-to-rail, meaning it can swing very close to the supply rails.
5.5 Gain Setting
The gain of the AD623 is set by an external resistor (RG) connected between the two RG pins. The module includes a trimpot for adjustable gain. If no external resistor is used, the module operates at unity gain (G=1).

6. Operating Instructions
Once the module is correctly wired and powered, it will amplify the differential input signal according to the set gain. The gain can be adjusted from 1 to 1000. For precise gain adjustment, use a multimeter to monitor the output and adjust the onboard trimpot. For specific gain calculations with an external resistor, refer to the AD623 datasheet.
7. Maintenance
The AD623 module is a robust electronic component and requires minimal maintenance. Keep the module clean and free from dust and moisture. Avoid exposing it to extreme temperatures or mechanical stress. Ensure all connections are secure to prevent intermittent operation.
8. Troubleshooting
- No Output/Incorrect Output:
- Verify power supply connections and voltage levels.
- Check input signal connections (IN+, IN-).
- Ensure the REF pin is correctly connected, typically to ground.
- Inspect for any short circuits or loose connections.
- Unstable Output:
- Check for proper grounding.
- Ensure power supplies are stable and free from noise.
- Verify that the input signal is within the specified common-mode range.
- Gain Issues:
- If using the onboard trimpot, ensure it is not damaged and is properly adjusted.
- If using an external resistor, verify its value and connection.
9. Specifications
| Parameter | Value |
|---|---|
| Brand Name | diymore |
| Type | Module (Amplifier Module) |
| Condition | New |
| Supply Voltage | 3V to 12V (single or dual supply) |
| Input Voltage Range | Extends 150mV below ground (single supply) |
| Operating Temperature | -10 °C to 65 °C |
| Origin | Mainland China |
| Max Supply Current | 550 µA |
| Gain Range | 1 to 1000 |
| Bandwidth (G=1) | 800 kHz |
| Settling Time (G=10, 0.01%) | 20 µs |
| Gain Accuracy (G=1) | 0.10% |
| Gain Accuracy (G>1) | 0.35% |
| Noise (RTI at 1kHz) | 35 nV/√Hz |
10. User Tips
- The onboard trimpot for gain adjustment is highly sensitive. Once the desired gain is set, consider applying a small spot of hot glue to the trimpot to secure its position and prevent accidental changes.
- The included header pins may require cleaning before soldering to ensure good electrical contact.
11. Warranty and Support
For any technical assistance or inquiries regarding the AD623 module, please contact diymore customer support. Refer to your purchase documentation for specific warranty details.
A detailed user manual in PDF format is also available for download. Please check the product page or contact support for the download link.
12. Safety Warnings
⚠ WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.