INSE N3T

Contents

INSE N3T Cordless Vacuum Cleaner User Manual

Model: N3T

1. Product Introduction

The INSE N3T Cordless Vacuum Cleaner is designed for efficient and versatile cleaning across various surfaces. This lightweight stick vacuum offers powerful suction and a multi-stage filtration system to ensure a clean home environment.

INSE N3T Cordless Vacuum Cleaner highlighting key features
The INSE N3T Cordless Vacuum Cleaner features 20000Pa suction, a 2000mAh large capacity battery for up to 40 minutes runtime, an ultra-lightweight and flexible LED motorized head, and a 5-stage HEPA filter system.

2. Package Contents

Please check the package contents against the list below to ensure all components are present.

Exploded view of INSE N3T Cordless Vacuum Cleaner components
Exploded view of the vacuum cleaner showing all included parts for assembly.
NameQuantityNameQuantity
Main Motor1Wall Bracket1
Metal Tube1Adaptor1
Floor Brush1Filter1
2-in-1 Brush1HEPA1
Clean Brush1

3. Setup

3.1 Wall Mount Installation

  1. Choose a location close to a power outlet.
  2. Ensure the location is high enough on the wall to allow the metal tube and floor nozzle to hang freely.
  3. Place the wall mount against the wall and use a pencil to mark the drill holes.
  4. Drill holes (with a 1/4" bit) and insert the drywall anchors.
  5. Insert screws through the mounting holes and tighten until firmly attached.

3.2 Vacuum Assembly

  1. Slide the telescopic tube onto the main motor until it clicks into place.
  2. Push the telescopic tube into the floor brush until it clicks.

3.3 Accessory Connection

Accessories such as the 2-in-1 brush or clean brush can be connected directly to the main motor or to the telescopic tube for cleaning high or hard-to-reach areas.

4. Operation

4.1 Initial Charging

The battery is not charged when shipped from the factory. Ensure the battery is fully charged before first use.

INSE N3T Cordless Vacuum Cleaner charging methods
The image illustrates two charging methods: wall-mounted charging and direct adapter charging. The vacuum offers 15-40 minutes runtime and takes 4-4.5 hours for a quick charge.

Charging Method 1 (Wall-mounted)

  1. Mount the main motor onto the wall bracket.
  2. Connect the adapter to the charging port on the main motor and plug into a power outlet. The power indicator will flicker during charging.

Charging Method 2 (Flat Surface)

  1. Place the main motor on a flat surface.
  2. Connect the adapter to the charging port on the main motor and plug into a power outlet. The power indicator will flicker during charging.

General charging time: 4-5 hours.

Tip: To prevent the appliance from dropping, it is recommended to remove the floor brush and conductive metal tube, and place the main unit horizontally for charging.

4.2 Power On/Off and Suction Modes

  1. Press the 'Power Switch' button to turn on the vacuum cleaner.
  2. Press the 'MAX' button to switch between intense cleaning mode and energy-saving suction mode, depending on your cleaning needs.
  3. Press the 'Power Switch' button again to turn off the vacuum cleaner.
INSE N3T Cordless Vacuum Cleaner cleaning various surfaces
The INSE N3T provides powerful cleaning on carpet and hard floors, effectively picking up dust, hair, crumbs, and gravel from tile, rug, low-pile carpets, and hardwood floors.
INSE N3T Cordless Vacuum Cleaner in 3-in-1 configurations
The 3-in-1 multifunction vacuum cleaner can be used as a stick vacuum for floors, a handheld vacuum for furniture, and with the extension tube for high-reach areas.

4.3 Product Demonstration Video

Watch this video for a visual guide on assembling, operating, and maintaining your INSE N3T Cordless Vacuum Cleaner.

This video demonstrates the INSE N3T Cordless Vacuum Cleaner in action, showcasing its assembly, cleaning capabilities on various surfaces, use of different attachments, dustbin emptying, filter washing, and charging process.

5. Maintenance

To ensure optimal performance and longevity of your vacuum cleaner, regular maintenance of its components is strongly recommended.

5.1 Cleaning the Main Motor (Non-electrical Parts)

  1. Turn off the vacuum cleaner before cleaning.
  2. Wipe the surface with a clean, damp cloth.
  3. Be cautious not to let water enter the inner parts of the main motor.

Important: Do not place the vacuum cleaner under direct sunlight or in wet conditions after cleaning.

5.2 Cleaning the Detachable Roller Brush

If the roller brush becomes tangled or stuck, an alert will appear on the LED display. Clean it promptly.

  1. Unlock the side lock on the bottom of the cleaner head.
  2. Remove the side cover and take out the roller brush.
  3. Use the provided clean brush gadget to cut and remove tangled hair.

5.3 Dustbin Emptying

Regularly empty the dustbin to maintain consistent suction power.

  1. Hold the cleaner over a waste bin.
  2. Press the lever to release the bottom lid of the dust cup and empty the contents.
  3. To remove the dust cup completely, twist it to the 'unlock' position, empty it, then reattach and twist to 'lock' position.

5.4 Filter Cleaning

Regularly check and clean the plastic filter screen and filter. Replace if damaged or if suction performance cannot be maintained.

Diagram of INSE N3T Advanced Cyclonic Filtration System
The advanced cyclonic filtration system efficiently captures and separates 99.99% of dirt using a High Density Sponge, Cyclone Filtration, High Efficient Filter Pad, Honeycomb Filter, and First Cyclone.
INSE N3T Cordless Vacuum Cleaner dustbin and filter washing
The dust container and filter are washable for easy maintenance. The image shows the filter components being rinsed under running water.
  1. Detach the main motor and dust cup. Remove the filter from the main motor and the filter component from the dust cup.
  2. Hold the strainer, rotate the filter holder, and remove the filter.
  3. If the filter screen and filter are too dirty, wash them with cool water. Clean the filter with the cleaning brush.
  4. Ensure the plastic filter screen and filter are completely dry before refitting.

Caution:

  • Pay attention to sharp objects like glass to prevent injury.
  • Do not wash the mechanical part of the dust box.
  • Ensure all parts are completely dry before next usage.
  • Do not bend or squeeze the filter.
  • Ensure the filter is correctly secured during assembly.
  • Change the filter if damaged or if cleaning does not restore it to its pristine state.

6. Troubleshooting

If you encounter any issues with your INSE N3T Cordless Vacuum Cleaner, please refer to the table below for common problems and solutions.

ProblemPossible CauseSolution
Running time shortenedBattery needs replacement.Contact customer service to replace the battery.
Ambient temperature is too high or too low.Operate in a suitable ambient temperature.
Battery is not fully charged.Charge the battery fully.
No suction powerDust cup is full.Clean the dust cup after use to prevent build-ups.
Filter is blocked.Remove any dust or debris from the filter.
Accessory is blocked.Check for blockages in the brush and other attachment points.
Suction inlet of brush or other is blocked.Check for blockages in the brush and other attachment points.
Parts of the appliance are not fully dried after cleaning.Ensure all components are properly dried after washing.
No chargingAmbient temperature when charging is too low or too high.Charge the machine under the right temperature environment (5°C-40°C).

7. Safety Instructions

Do not place the vacuum cleaner close to heat sources, radiation, or burning cigarettes.

  • Do not use the appliance to remove the following objects:
    1. All liquids such as water and solvents.
    2. Lime, cement, ash, and other construction dust and garbage.
    3. Hot objects, such as cigarette butts.
    4. Sharp debris, such as glass shards, etc.
    5. Flammable and explosive articles, such as gasoline or alcohol products.
  • Do not let children play with or operate the vacuum cleaner to prevent accidents.
  • Your vacuum cleaner is an electric appliance: it must be used appropriately. Do not leave the operating vacuum cleaner unattended.
  • The power must be turned off during cleaning, maintenance, or when in storage.
  • Do not pull the power plug to turn off the vacuum cleaner. Hold the plastic part of the plug to remove it from the power socket.
  • The power supply voltage must correspond to that of the vacuum cleaner charging voltage.
  • Keep the power cord away from sharp objects to prevent it from being damaged.
  • To prevent fires, do not immerse the vacuum cleaners in water, or expose them to any heating appliances.
  • Do not drag the power cord when moving the charging station.
  • In the case of the below situations, do not use the vacuum cleaner and send it immediately to the nearest approved maintenance facility if:
    • The vacuum cleaner fell and consequently damaged.
    • The power cord is damaged.
  • Stop operating the vacuum cleaner if the suction inlet is blocked to prevent damages (such as overheating) to the motor or deformations to the vacuum plastic part occasioned by overheating motor.

8. Specifications

ParameterValueParameterValue
Product CategoryN3K, N3X, N3E, N3P, N3TWeight (All Accessories Included)1.8KG
Net weight1.1KGNominal Voltage18V
Nominal Power180WAdaptor Input100V-240V~50/60Hz
Battery Capacity2000 mAhAdaptor Output22V
Retractable Tube47/77cmSize43.5*28.5*18.0cm

9. Warranty & Support

This warranty term provides specific legal rights, and you may also have other rights which vary from state to state.

9.1 24-month Warranty & Lifetime Customer Support

This warranty applies only to eligible purchases made directly from authorized distributors. Coverage applies to the original owner and the original product only and is not transferable.

9.2 How to Initiate a Warranty Claim

If your appliance operates improperly under normal household conditions within the warranty period, please contact customer support at support@vacservice.vip to fill out the warranty form and initiate a claim.

A user manual in PDF format is available for download and further details: View User Manual (PDF)

10. User Tips

  • For optimal performance, ensure the dustbin is emptied regularly, especially after cleaning large debris or pet hair.
  • Always check the roller brush for tangled hair or fibers, as this can reduce suction power and trigger an LED alert.
  • When charging, place the vacuum in a stable position to prevent accidental falls. If wall-mounting, ensure the bracket is securely installed.
  • Periodically inspect and clean all filters to maintain strong suction and prevent motor strain. Allow filters to dry completely before reassembly.
  • If the vacuum is not used for an extended period (more than 2 months), disconnect it from the power supply and ensure it is fully charged every two months to preserve battery life.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.