1. Safety Warnings
Please read all warnings carefully before operating the drone.
- The packaging and instructions contain important information and should be kept.
- You are responsible for ensuring that no harm will be caused to the personal and property of others.
- Commissioning and installing of aircraft must be strictly in accordance with the operating instructions. Maintain a distance of 2 to 3 meters from the aircraft to prevent injury during flight and landing.
- The company and distributors are not responsible for any loss, damage, or injury caused by improper use or operation.
- Children should be guided by adults. This product is prohibited for children under 14 years old.
- Follow instructions for installation and use. Some parts require adult assembly.
- The product contains small parts; keep out of reach of children to prevent accidental eating or suffocation.
- Do not operate on roads or in areas with accumulated water to avoid accidents.
- Put away packing materials promptly to avoid harm to children.
- Do not disassemble or modify the aircraft, as this may cause malfunction.
- The charging cable must be inserted into the designated power supply (5V=2A) as specified on the product label.
- Using other charging cables will damage the battery and may cause unexpected dangers.
- The charging cable is not a toy.
- When charging the rechargeable battery, it must be under adult supervision, away from flammable materials. Do not leave the monitoring range during charging.
- Do not short-circuit or squeeze the battery to avoid explosion.
- Do not mix different types of lithium batteries.
- The aircraft uses a rechargeable lithium battery, which needs to be pulled out for charging.
- Do not short-circuit, decompose, throw the battery into fire, or place it in high-temperature environments (e.g., near electric heating devices).
- Keep the aircraft away from other electrical equipment and magnetic objects to prevent mutual interference.
- Maintain a safe distance from the high-speed rotating propeller to avoid scalp or cuts.
- The motor is a hot part; do not touch it to avoid burns.
- LEDs emit laser radiation; do not direct the light beam at others.
- Do not use the model near your ears! Misuse may cause hearing damage.
- The USB charging cable must be the one provided by the manufacturer. Using other cables will cause serious damage to the battery and lead to unexpected danger.
- To meet aeronautical radio station requirements, the model remote control should be stopped within city areas as required by relevant state departments.
- Turn off the switch and unplug the battery when the aircraft battery is depleted. Charge after 30 minutes of rest to prevent battery damage.
Disclaimer: Not suitable for children under 36 months.
2. Accessories Included
The package includes the following items:
- Aircraft x1
- Remote control x1
- Micro USB cable x1
- Type-C Charging Cable x1
- Lithium battery x1
- Fan blade x4
- Screwdriver x2
- Operating Instructions x1
3. Product Overview
3.1 Name of Each Part of Aircraft
- Fan blade
- Obstacle Avoidance Radar
- Shell
- Camera
- Optical camera
- Battery
- Aircraft power switch
- Motor
3.2 Name of Each Part of the Remote Control
- Antenna
- Left stick
- Right rocker
- Unlock (long press)
- Power switch (long press)
- Obstacle avoidance switch (long press)
- Headless mode (short press) / one key return (long press)
- Power Indicator
- GPS indicator light
- Obstacle avoidance indicator light
- Return indicator light
- Charging port
- Display screen
- Micro SD card slot
- GPS switch (long press)
- Fine tuning of camera angle
- Horizontal calibration (short press) / Geomagnetic calibration (long press)
- Speed gear
4. Setup Guide
4.1 MicroSD Card Installation
To install the SD card, insert it carefully until it is firmly in position. To remove, gently press the memory card until you hear a click sound, then carefully pull it out. Ensure the SD card is inserted before starting the drone for photo and video capture.
Note: A micro SD card must be installed to take photos and videos during flight.
4.2 Lithium Battery Charging Instructions
Aircraft Battery:
- Push the battery rightwards into the aircraft in accordance with the drawing.
- To remove, pull the battery out.
- Insert the USB port of the USB charging cable into a computer USB port or a 5V=2A power adapter. Connect the other end of the USB charging cable to the battery socket. The red indicator on the module battery will be on during charging and turn off when fully charged.
Note: When the aircraft is not in use, do not leave the battery installed in the aircraft to avoid battery damage.
Remote Controller Battery:
- Plug the USB interface of the USB charging cable into a computer USB port or a 5V=2A power adapter. Plug the other end into the charging port of the remote controller.
- During charging, all indicator lights on the remote controller will light up in turn and remain on when fully charged. Power off the remote controller before charging.
Warning: Only use the aircraft charging cable provided by the factory. Using other charging cables can cause serious damage and unexpected dangers.
4.3 Installation of Airplane Components
Radar Installation:
- Use a flat-blade screwdriver to pry the parts on the body.
- Align the two sides of the pressed radar part and butt them onto the body as indicated by the arrows.
Note: The radar component location contains electronic parts; do not use in water or humid environments.
Wind Blade Installation:
Unscrew the screw and remove the fan blade. Install new fan blades, ensuring they are correctly oriented (A to A, B to B) as indicated by the letters on the blades and the diagram. Incorrect installation will prevent takeoff.
Note: The fan blade is printed with letters of A and B. Install correctly according to the diagram, otherwise it cannot take off.
4.4 Unfolding Steps of the Aircraft
The aircraft is in a folded state when shipped from the factory. Unfold the aircraft according to the steps shown in the diagram (refer to manual page 6 for visual guide).
4.5 APP Download and Installation
Scan the QR code provided in the manual (page 6) to download the 4DRC PRO app. For Android, open the download in your browser. For iOS, download from the App Store.
Link Description:
- Power on the aircraft, then the remote controller, and wait for frequency pairing. After successful pairing, connect your mobile phone to the remote controller's image transmission interface via a data cable. Go to your phone's settings, turn on Wi-Fi, find the device named "4DRC*******" in the network list, and connect.
- Open the "4DRC PRO" app icon on your mobile phone to enter the control interface. (Try to stay away from other signal source environments when flying).
5. Operating Instructions
5.1 Environmental Requirements Before Flight
Choose an outdoor and open environment with no rain, snow, or strong wind. Stay away from crowds, trees, wires, tall buildings, airports, and signal transmission towers. Do not fly in small indoor environments with many obstacles.
5.2 Pre-flight Preparation (Using Remote Control)
Turn on Aircraft Power: Turn on the aircraft and place it on a horizontal surface. The fuselage lights will flash, indicating it's in frequency matching state.
Note: Ensure the aircraft is placed correctly on a horizontal plane with its nose facing forward.
Remote Control Frequency Matching: Long press the power switch button on the remote control. The indicator light will flash. Push the left joystick to the top, then to the bottom. The aircraft lights will stop flashing and remain on constantly, indicating successful frequency matching.
Warning: Both the aircraft and remote controller must have sufficient power before takeoff.
WIFI Connection: Turn on Wi-Fi on your mobile device, select "4DRC*******" from the Wi-Fi list, and open the app after successful connection.
Note: The "4DRC PRO" app is required for this step.
5.3 Calibration Operations
Horizontal Calibration: Short press the horizontal calibration button on the remote control. The blue and red lights on the aircraft will flash quickly, then remain on, and the remote controller will emit a "beep" when calibration is complete. In the APP, click "Set more" and follow prompts for horizontal calibration.
Note: The aircraft must be placed on a horizontal surface for calibration.
Geomagnetic Calibration:
- Long press the geomagnetic calibration key until the front blue light and rear red light on the aircraft flash.
- Rotate the aircraft clockwise horizontally until the front blue light and rear red light flash slowly. The remote controller will emit a "beep".
- Pick up the aircraft with its nose vertically down and rotate it clockwise until the blue light on the front and red light on the rear of the aircraft are always on. The remote control will emit a "beep", indicating successful calibration.
In the APP, enter "Setting more" and follow the text prompts for geomagnetic calibration.
Note: After geomagnetic calibration, perform level calibration again.
5.4 Star Search Status (GPS Mode)
In GPS mode, the GPS indicator light on the remote controller flashes slowly, indicating satellite search. The aircraft indicator light will be always on. When the remote controller's GPS indicator light is always on and the aircraft's red indicator light flashes, satellite search is successful, and the remote controller emits a "beep". The aircraft can then take off.
Note: Wait a few minutes for the first search. The drone can only take off when the app shows three or more satellite signal bars (remote controller displays 10 or more satellite indices).
5.5 Start/Stop (GPS Mode)
Push the left and right joysticks on the remote controller outward to unlock, or long press the unlock key. The aircraft can take off, and all indicator lights will be on after takeoff. (Without successful satellite search, the aircraft can be unlocked but cannot take off).
In the APP, click the "One Key Unlock" icon to achieve this function.
Warning: Before flying, ensure all pre-flight steps are completed in order: open aircraft -> remote control frequency matching -> WIFI connection -> horizontal calibration -> geomagnetic calibration -> star search status -> start/stop (GPS mode).
5.6 Remote Control Method
In the APP, enter the control interface and click the "more functions" icon to open the "joystick on/off" icon to see the operation joystick on the interface. The operation method is as follows (refer to manual page 11 for visual guide):
- Left Joystick (Throttle): Push up to increase main blade rotation rate and ascend. Push down to decrease main blade rotation rate and descend.
- Left Joystick (Rudder): Push left to turn aircraft nose left. Push right to turn aircraft nose right.
- Right Joystick (Rudder): Push up to move aircraft forward. Push down to move aircraft backward.
- Right Joystick (Rudder): Push right to deviate aircraft fuselage right. Push left to deviate aircraft fuselage left.
Warning: When the aircraft is within 1m of the ground, it may become unstable due to "ground effect response". The lower the height, the greater the effect.
5.7 Flight Modes and Features
Obstacle Avoidance Mode (No obstacle avoidance in GPS mode): During flight, press and hold the obstacle avoidance switch key (e) to activate. The aircraft will hover and stop moving if close to obstacles. Press and hold again to deactivate.
Note: Under strong sunlight, with transparent/reflective objects (like glass), or black objects, obstacle avoidance may be weak or ineffective.
One Key Return: Press the return button. The aircraft will return to the takeoff position. If below safe altitude, it will rise first. Manually control the directional lever to avoid obstacles during descent. In APP, click the "one-key return" icon. Click again to cancel return.
Warning: Out-of-control return (signal loss for ~4s) will automatically return. Low-battery return will force return to ~10m above takeoff. Low-battery return cannot be canceled.
Headless Mode: The aircraft's front when code-matching is turned on is the default front. Short press the remote controller "headless mode" function key to adjust direction. Tap gently to exit.
Special Tip: Ensure aircraft is aligned with a straight line and let gyroscope automatically detect for straight line flight in headless mode.
Speed Switching: After takeoff, low-speed mode is default (3-gear). Push the wheel remote controller right for higher speeds (one, two, or three "beeps" for increasing speed). Push left to lower speed. In APP, click "More Functions" icon to switch flight speed.
Lens Adjustment: Pull the fine-tuning wheel of the camera angle on the remote controller to adjust. In APP, click "More Functions" icon to enter lens adjustment and adjust as needed.
Normal Mode Start/Stop (Indoor Operation): If GPS indicator on remote control is off:
- Long press the GPS button on the remote control until the GPS indicator is off, entering normal mode.
- Push left and right rockers on the remote controller outward to unlock, or long press the unlock key.
- Then push up the left joysticks.
Multipoint Flight Mode (GPS Mode): In APP, click "More Functions" icon to enter waypoint flight. Set single or continuous waypoints on the map. Click the send icon to start flight along the preset trajectory. Joystick can control direction during flight.
Orbital Flight Mode (GPS Mode): In APP, click "More Features" icon to enter orbit flight mode. Aircraft will orbit in a radius. Radius can be adjusted in APP. Push right direction joystick left/right for default speed orbital speed adjustment. Push front/rear for orbit radius adjustment. Press orbit button again to end.
GPS Follow Mode: In APP, click "More Functions" icon to enter follow mode. Aircraft uses distance to operator's mobile device as reference, tracking changes in location. Lightly press the red icon to cancel.
Gesture Recognition: Facing the camera's front lens, click the gesture photo button in the APP. Use gestures to trigger photo or camera functions:
- Yeah gesture photo: Make a "Yeah" gesture with one hand horizontally ~3m in front of the lens. After recognition, a 3-second countdown starts before taking photos.
- Palm gesture video-recording: Put five fingers together and lift one hand horizontally ~3m in front of the lens. After recognition, recording starts. Recording ends when the gesture is re-recognized (time difference > 3s).
Special prompt: Aim directly at the lens and perform gesture recognition ~2-3M away in good light and background.
MV Interface: Click the "filter interface" icon in the APP. Choose a filter effect, click recording icon to start. After recording, the short video or picture is saved to the media library.
Special prompt: During recording, you can rotate the screen, switch filter effects, and turn joystick on/off to control direction and altitude.
5.8 Display Screen Interface Function Introduction
The remote control's display screen provides various information and controls (refer to manual page 4 for visual guide):
- Return
- Scroll up/down
- Screen off (long press)
- Confirm (long press for 3 seconds for Wi-Fi connection and image interface)
- Photo
- Video
- Reverse the lens
- Edit (Option to delete files)
In the file browsing interface, press the confirm button to select an image or video, then press again to enter the selection page, and press once more to select the file.
5.9 APP Control Interface Function Introduction
The APP interface provides comprehensive control and information (refer to manual page 7 for visual guide):
- Satellite signal
- Flight status
- More features
- Return
- WIFI signal
- Aircraft battery power
- Parameter settings
- Takeoff/landing
- One-key return
- Unlock
- Map
- Flight distance (default 30m, adjustable 20m-10000m)
- 3D stereo
- Reverse the lens
- Gesture photo
- Music
- Lens adjustment
- Beginner mode
- Photo / Video
- Shutter
- Media library
- Filter
- Flight record
- Zoom
- Multipoint flight
- Follow
- Orbital flight
- Find the plane
- Speed gear
- Touch joystick
- Lens switching
- On/Off
- Save
- Flight altitude (default 30m, adjustable 10m-120m)
- Time-lapse photography
Note: After becoming proficient in flight operation, close novice mode and set flight distance and altitude before flying further!
Note: Before shooting, click the menu to select.
5.10 Official Product Video
6. Maintenance
- Regularly check fan blades for damage and replace if necessary.
- Ensure batteries are charged using only the provided charging cables.
- Store the drone and remote control in a dry environment, away from extreme temperatures.
- When not in use for extended periods, remove the battery from the aircraft to prevent damage.
- Keep the camera lenses clean for optimal image quality.
7. Troubleshooting (FAQ)
| Question | Reason | Solution |
|---|---|---|
| The aircraft indicator flashes without any response |
|
|
| The blades of the aircraft rotate but cannot fly |
|
|
| The aircraft vibrates badly | Blade deformation | Replace the blade. |
| Fine tuning is done but still can't make the aircraft stable |
|
|
| After the impact, start the aircraft again and it flies uncontrollably | The three-axis acceleration sensor loses its balance due to impact | It will be OK after 5-10s of resting the aircraft, or by geomagnetic calibration and level calibration (refer to 12.4 horizontal calibration operation in the full manual). |
8. Specifications
Aircraft
- Model: 4D-F8
- Drone Weight: 160g
- Takeoff Weight: about 249g
- Dimensions: 22*18*7.5cm
- Material: Plastic, Metal
- Motor: Brushless Motor
- Video Capture Resolution: 4K UHD, Other
- Camera Mount Type: Fixed Camera Mount, Other
- Features: App-Controlled, FPV Capable, GPS, Wi-Fi, Other
- Aerial Photography: Yes
- Operating Frequency: 2.4GHz
- Hover/Flight Noise: 80.5/82.3 (dB)
- Anti-wind Ability: <10km/h
- Indoor/Outdoor Use: Indoor-Outdoor
- State of Assembly: Ready-to-Go
- Power Source: Electric
- Charging Voltage: 7.4V
- Charging Time: about 180mins
- Flight Time: 20~30 minutes
- Remote Distance: 3000M
- Transit Time (Days): 2000M (likely refers to range)
- Control Channels: 4 channels
- Operator Skill Level: Beginner, Intermediate, Expert
- Recommend Age: 14+y
- Hign-concerned Chemical: None
- Is Electric: Lithium Battery
- Is Batteries Included: Yes
- Plugs Type: USB
- Set specification: Single battery (total weight 332g)
- Package Includes: Original Box, Camera, Batteries, Remote Controller, USB Cable, Operating Instructions
Remote Control
- Operating Voltage: 3.7 V
- Operating Frequency: 2.4GHz
- Controller Battery: 3 x 1.5 AAA Battery (not included)
- Controller Mode: MODE1, MODE2
- Remote Control: Yes
Environmental
- Temperature of working environment: 0°C to 40°C
- Charging ambient temperature: 5°C to 40°C
9. User Tips
- Maximize Battery Life: To get the most out of your 20-30 minute flight time, avoid aggressive maneuvers and flying in strong winds, which can drain the battery faster. Always ensure the battery is fully charged before each flight.
- Understand Flight Range: The drone boasts a remote distance of up to 3000M. However, environmental factors like signal interference, obstacles, and weather can affect actual range. Always maintain visual line of sight with your drone.
- Language Settings: The remote control screen offers language options (e.g., Chinese and English). If you need to change the language, navigate to the settings menu on the remote control's display.
- Obstacle Avoidance for Beginners: The F8 MAX model features 360° intelligent obstacle avoidance. While this is a great feature for beginners, remember its limitations in certain conditions (strong sunlight, transparent/reflective objects, black objects). Always fly with caution.
10. Warranty and Support
Warranty: This product comes with a 30-day warranty from the date of purchase. Please retain your proof of purchase for any warranty claims.
Support: For further assistance, technical support, or inquiries not covered in this manual, please refer to the official 4DRC website or contact the seller directly. You can also refer to the comprehensive user manual available as a PDF for more detailed information: