MASO 13mm Flat Sensors Car Parking Sensor System

Contents

User Manual: Car Parking Sensor System

Model: 13mm Flat Sensors Car Parking Sensor System

Brand: MASO

1. Introduction

Thank you for choosing the MASO Car Parking Sensor System. This system is designed to enhance your driving safety by providing audible alerts when obstacles are detected during parking maneuvers. Featuring advanced ultrasonic technology and a user-friendly design, it helps prevent collisions and makes parking easier and safer.

Please read this manual thoroughly before installation and use to ensure proper function and longevity of your device.

2. Safety Information

Warning:

  • Installation should ideally be performed by a qualified professional to avoid damage to the vehicle or the system.
  • Always disconnect the vehicle's battery before beginning any electrical installation to prevent short circuits or electrical shock.
  • Ensure all wiring is properly insulated and secured to prevent interference or damage.
  • This system is an aid to parking and should not replace careful driving and visual checks. Always be aware of your surroundings.
  • Do not press the sensors excessively during installation.
  • Improper installation may lead to system malfunction.

3. Package Contents

Verify that all items listed below are included in your package:

  • 1 x Main Control Box
  • 4 x Parking Sensors (with 2.5m cables)
  • 1 x Power Cable
  • 1 x Hole Saw (for sensor installation)
  • 1 x Buzzer (Speaker)
  • 1 x User Manual (this document)
All components of the parking sensor kit laid out: main control box, buzzer, four parking sensors, power cable, and hole saw drill bit.
Figure 3.1: Complete Parking Sensor Kit Components

4. Specifications

FeatureDetail
Control UnitDual CPU, Advanced Chipset
Sensor TypeUltrasonic, Flat Design (13mm)
Sensor Quantity4
Detection Range0 cm ~ 2.5 meters
Rated Current20-200mA
Input Power9 ~ 16V DC
Operating Temperature-30°C ~ +70°C
Display Operating Temperature-20°C ~ +60°C
Alarm Voice> 80dB (Adjustable)
Ultrasonic Frequency40KHz
Environmental ResistanceAnti-freeze and Rain-proof
Control Box Dimensions58mm (L) x 50mm (W) x 23mm (H)
Package Dimensions24cm (L) x 16cm (W) x 5cm (H)
Package Weight0.44 kg
Detailed view of the main control box, showing its dimensions (58mm length, 50mm width, 23mm height) and the input/output ports for power and sensors.
Figure 4.1: Main Control Box Dimensions and Ports

5. Installation Guide

This section provides general guidance for installing the parking sensor system. Specific vehicle models may require variations in procedure. Professional installation is recommended.

5.1. Preparation

  • Ensure the vehicle's engine is off and the ignition is switched off.
  • Disconnect the negative terminal of the vehicle's battery to prevent electrical hazards.
  • Gather necessary tools: drill, masking tape, measuring tape, marker, wire strippers, electrical tape, zip ties.
  • Determine the optimal placement for the sensors on your bumper. Typically, sensors are evenly spaced across the rear bumper.
Diagram illustrating the placement of parking sensors on a car's rear bumper and the ultrasonic detection zones.
Figure 5.1: Recommended Sensor Placement

5.2. Sensor Installation

  1. Mark the desired locations for the four sensors on the bumper. Ensure they are evenly spaced and at a consistent height.
  2. Use the provided hole saw drill bit to carefully drill holes at the marked locations.
  3. Insert each sensor into its respective hole. Ensure the sensor is flush with the bumper surface and oriented correctly (if applicable). The flat design allows for a clean, integrated look.
  4. Route the sensor cables through the bumper and into the vehicle's interior, typically through existing grommets or a newly drilled, sealed hole.
Technical diagram comparing the recommended 16.5mm sensor installation depth with an incorrect 25mm depth, emphasizing the importance of precise drilling.
Figure 5.2: Sensor Installation Depth Guide (16.5mm recommended)
Four parking sensors with 3M adhesive backing for secure mounting, alongside the specialized hole saw drill bit.
Figure 5.3: Sensors and Hole Saw

5.3. Wiring Connections

  1. Connect the 2-pin connectors of each sensor cable to the corresponding ports on the Main Control Box.
  2. Connect the power cable to the Main Control Box. The power cable typically has three wires:
    • Red Wire: Connect to the vehicle's reverse light positive (+) wire. This ensures the system activates when reverse gear is engaged.
    • Black Wire: Connect to the vehicle's ground (-) wire.
    • Yellow Wire (if present): Connect to a constant 12V power source (e.g., accessory fuse) if the system is designed for front sensors or continuous monitoring. For rear-only systems, this may not be used or connected to the reverse light positive as well.
  3. Connect the buzzer (speaker) to the designated speaker port on the Main Control Box.
Rear view of the main control box, clearly labeling the 'Power' and 'Speaker' connection ports.
Figure 5.4: Control Box Connections
Close-up of the main control box with sensor cables connected, illustrating the 2-pin connector type for the sensors.
Figure 5.5: Sensor Cable Connections to Control Box

5.4. Securing Components

  • Mount the Main Control Box in a secure, dry location within the vehicle's trunk or cabin, away from excessive heat or moisture.
  • Secure all cables with zip ties to prevent them from dangling, interfering with moving parts, or being damaged.
  • Mount the buzzer in a location where the audible alerts can be clearly heard by the driver, but not obstructed.
Close-up of the buzzer unit, highlighting the 'Off', 'Lo' (Low), and 'Hi' (High) volume adjustment switch.
Figure 5.6: Buzzer with Volume Control

5.5. Final Steps

  • Reconnect the negative terminal of the vehicle's battery.
  • Test the system as described in the "Operation" section.

6. Operation

The MASO Car Parking Sensor System is designed for automatic operation when the vehicle is in reverse gear.

  1. Engage the vehicle's reverse gear. The parking sensor system will automatically activate.
  2. As the vehicle approaches an obstacle, the buzzer will emit an audible warning.
  3. The frequency of the beeps will increase as the vehicle gets closer to the obstacle.
  4. For models with adjustable buzzer volume, use the switch on the buzzer unit to select 'Off', 'Lo' (Low), or 'Hi' (High) as per your preference.

Detection Zones and Alarm Frequency:

  • Far Distance (e.g., 1.5m - 2.5m): Slow, intermittent beeps.
  • Medium Distance (e.g., 0.5m - 1.5m): Faster, more frequent beeps.
  • Close Distance (e.g., 0m - 0.5m): Continuous solid tone.

Note: The exact distances for each alarm stage may vary slightly based on environmental factors and sensor calibration.

7. Maintenance

  • Sensor Cleaning: Regularly clean the surface of the parking sensors to ensure optimal performance. Dirt, mud, snow, or ice can obstruct the ultrasonic waves and lead to inaccurate readings. Use a soft cloth and mild cleaning solution.
  • Wiring Inspection: Periodically check all wiring connections for any signs of wear, corrosion, or loose connections. Secure any loose wires.
  • System Check: Occasionally test the system by reversing towards a known obstacle to ensure it is functioning correctly.
  • Environmental Protection: While the sensors are anti-freeze and rain-proof, avoid directing high-pressure water jets directly at them during car washes.

8. Troubleshooting

ProblemPossible CauseSolution
System does not activate when in reverse.No power to the control box; faulty reverse light connection; loose power cable.Check power cable connection to reverse light and ground. Ensure all connections are secure. Verify reverse light is functioning.
Buzzer does not sound or is too quiet/loud.Buzzer volume switch set to 'Off' or incorrect level; loose buzzer connection.Check the volume switch on the buzzer and adjust to 'Lo' or 'Hi'. Ensure the buzzer cable is securely connected to the control box.
Inaccurate or false alarms.Sensors are dirty or obstructed; improper sensor installation angle; electromagnetic interference.Clean sensors thoroughly. Verify sensors are installed flush and correctly angled. Check for nearby sources of strong electromagnetic fields.
One or more sensors not detecting.Faulty sensor; loose sensor cable connection.Check the connection of the specific sensor to the control box. Inspect the sensor cable for damage. If problem persists, the sensor may need replacement.
System continuously beeps.Sensor obstructed; sensor too close to the ground or vehicle part; faulty sensor.Ensure no objects are directly in front of sensors. Check sensor placement for obstructions from the vehicle itself (e.g., exhaust pipe). Clean sensors.

9. User Tips

  • For best performance, ensure sensors are mounted at a consistent height and are not angled too far upwards or downwards.
  • Consider the color of your bumper when choosing sensor color for a seamless look.
  • Always double-check connections, especially the reverse light trigger, to ensure the system activates reliably.
  • Test the system in an open area with a soft obstacle (e.g., a cardboard box) before relying on it in tight spaces.

10. Warranty and Support

For any issues or questions regarding your MASO Car Parking Sensor System, please contact the seller directly through the platform where you made your purchase. Keep your purchase receipt as proof of purchase for warranty claims.

Note: A PDF document titled 'Product Instruction Manual' was provided, but its content pertains to a 'Brake Light Switch' and not this Car Parking Sensor System. Therefore, the information from that PDF has not been included in this manual. Please rely on the instructions provided herein and contact your seller for product-specific manufacturer details or further support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.