ToolkitRC M6D

Contents

ToolkitRC M6D Dual Smart Charger User Manual

Model: M6D V1.1 (2020.05)

1. Introduction

Thank you for purchasing the ToolkitRC M6D multi-function charger. Please read this manual carefully before use to ensure the best experience with this product.

Key Points:

  • 💡 Tips: Helpful advice for optimal use.
  • ❗ Important: Critical information for safety and proper function.
  • 📄 Information: General details and explanations.

For further information, news, and firmware updates, please visit www.toolkitrc.com.

2. Safety Instructions

⚠ Warning: Please be aware of the potential fire risk and strictly follow the instruction manual for charging and storage.

  1. The M6D allows an input voltage of 7-28V. Please ensure that the power supply voltage is within this range. Pay attention to the positive and negative polarities of the power supply when connecting.
  2. Do not use this product in a hot area or near a heat source. Do not use this product in a damp, flammable, or explosive gas environment.
  3. Only use this product while under direct supervision. Do not leave charging batteries unattended.
  4. When not using this product, please unplug the input power in time.
  5. When using the charging function, please set the current matching with the battery. Do not set excessive current charging, so as not to damage the battery.

3. M6D Layout

The ToolkitRC M6D charger features a compact design with clearly labeled ports and controls for ease of use.

ToolkitRC M6D Charger Front View

Figure 3.1: Front View of M6D Charger
This image shows the front of the M6D charger with labels pointing to key components: Display, Scroll wheel (Turn: left or right, Press: OK), Exit key, CH key, Main port, Temp. Sensor Port, and Balance port.

ToolkitRC M6D Charger Back View

Figure 3.2: Back View of M6D Charger
This image displays the back of the M6D charger, highlighting the Input port (DC 7-28V), USB Output & upgrade port (5.0V 2.1A), and the Cooling fan.

4. Quick Start Guide

Follow these steps to quickly set up and begin using your M6D charger:

  1. Connect a 7-28V power supply or input battery to the input port on the back of the M6D.
  2. The display will show the boot logo for 2 seconds, accompanied by a 'do-re-mi' boot sound.
  3. After booting, the display will enter the main interface, showing charging status and battery information.
  4. Short press the [Exit] button to switch the cursor between the left and right channels.
  5. Press and hold [Exit] to start testing the internal resistance of the corresponding channel. After the test, the internal resistance will be displayed.
  6. Scroll the [Scroll Wheel] to switch between different pages in the corresponding channel.
  7. Short press [OK] to select a charging task when the channel is idle, or to adjust and end the work when the channel is active.
  8. Press and hold [OK] to enter the system setting interface when both channels are idle.
  9. Press [Exit] to end modifications or return to the previous interface.

💡 Tips for Navigation:

  • Short press [Scroll Wheel] once to confirm a key function.
  • Press and hold [Scroll Wheel] for 2 seconds to delete a key function.
  • A 'di-di' prompt tone indicates successful key operation.

Video 4.1: ToolkitRC M6D Product Demonstration
This video provides a visual guide to the M6D charger's features, showing how to navigate the interface and connect batteries for charging.

5. Charge and Discharge Settings

Short press [OK] on the main interface to enter the charging function. The following settings can be configured:

5.1. Battery Type

Scroll the [Scroll Wheel] to move the cursor and select a stored battery type, or create a new one. Press [OK] to enter the battery setting interface.

The charger supports charging and discharging of 6 types of batteries: LiPo, LiHV, LiFe, Lion, NiMh, and PB. Two modes of power supply and smart battery functions are also available.

❗ Warning: Choosing the wrong battery type may damage the battery, the charger, and poses a risk of burning. Please choose carefully. Do not use this product to charge batteries that do not indicate the battery type.

📄 Glossary of Battery Terms:

  • LiPo: Lithium polymer battery, nominal voltage 3.70V, fully charged at 4.20V.
  • LiHV: High-voltage lithium battery, nominal voltage 3.85V, fully charged at 4.35V.
  • LiFe: Iron-lithium battery, nominal voltage 3.30V, fully charged at 3.60V.
  • Lion: Lithium-ion battery, nominal voltage 3.60V, fully charged at 4.10V.
  • NiMh: Nickel-metal hydride battery, nominal voltage 1.20V.
  • PB: Lead-acid battery, nominal voltage 2.00V.

5.2. Number of Cells

Move the cursor to [Battery cell Number] and press [OK] to modify the number of battery cells. Turn the [Scroll wheel] to adjust the value. When set to [Auto], the charger will automatically recognize the number of connected battery cells according to the battery voltage connected to the output port.

💡 Tips: Over-discharging or over-charging may lead to incorrect recognition of the battery cell number. Manually set the correct cell number. If the cell number is set incorrectly, the battery may not be fully charged or may be damaged by overcharging. After a Lixx battery is connected to the balance port, the number of battery cells can be more accurately identified.

5.3. Mode

Move the cursor to [Mode] and press [OK] to modify the working mode. Available modes include Charge, DisCHG (Discharge), and StoCHG (Storage).

5.4. Discharge Mode

When the working mode is set to discharge, storage, or cycle, the battery setting interface will include discharge mode options.

M6D supports two discharge modes:

  1. Inter (Internal) Mode: Discharges through internal heat consumption, with a maximum support of 3.0A@12W.
  2. Recycle Mode: When the input is a suitable battery, this function can recover electric energy from the discharging battery to the input battery. Maximum support is 15.0A@250W discharge.

5.5. Input MaxVoltage

When Recycle discharge mode is selected, the battery setting interface will include the Input MaxVol setting. Move the cursor to [Discharge Mode] and press [OK] to adjust the input MaxVol. If the input voltage reaches this voltage during discharge, the discharge will stop.

💡 Tips: Please set the input cut-off voltage within the safe voltage range of the power supply battery. Setting a high over-voltage may damage the input power battery.

5.6. End Voltage (TVC)

Move the cursor to [End Voltage] and press [OK] to modify the end voltage of the single battery. When charging, this is the charging cut-off voltage. When discharging, it is the discharge cut-off voltage. Scroll the [Scroll Wheel] to adjust the value in steps of 0.01V.

💡 Tips:

  • Only LiPo, LiHV, LiFe batteries can set the end voltage.
  • If you are not familiar with battery characteristics, please do not modify the cut-off voltage.
  • The charging cut-off voltage can be set to a range of plus or minus 50mV of full voltage.
  • TVC: Terminal Voltage Control.

5.7. Current Setting

Move the cursor to [Charge Current] or [Discharge Current] and press [OK] to modify the current. Rotate the [Scroll Wheel] to adjust the value in 0.1A steps. Quickly scroll the [Scroll Wheel] to quickly increase or decrease the current. The charger supports up to 15.0A. In synchronous mode, maximum support is 25A.

💡 Tips:

  • Please set the charging rate of 1-2C according to the battery capacity. For example, for a 2000mAh battery, set the charging current to 2.0-4.0A.
  • Charging and discharging current settings are only valid in the corresponding working mode.

5.8. NiMH Setting (PeakV)

When the battery type is NiMh, you can set the negative pressure value when the battery is fully charged. The range is 5mV-15mV.

💡 Tips:

  • Only NiMh batteries can have negative battery voltage set.
  • PeakV: When the nickel-metal hydride battery is fully charged, the voltage drop of each piece peaks.

5.9. Cycle Setting

When the battery type is NiMh and the work mode is set to cycle, the battery setting interface will include options for the number of cycles and rest time. Move the cursor to [Cycle times] and press [OK] to set the cycle times (2-12). The charger will follow the pattern: discharging -> charging -> discharging -> charging... The [Rest time] can be set from 2 to 10 minutes.

5.10. Power Mode Setting

When the battery type is 'Power', the battery setting interface offers two options: Output Voltage and Max Current. The voltage range is 1V to 28V, and the current range is 0.5A to 15A.

5.11. Smart Battery Setting

When the battery type is 'Smart Battery', the settings are limited to the drone model type and maximum current. You can select different drone models (e.g., Mavic2 17.6V, MavicS 13.05V, Phantom 17.4V, Inspire 26.1V) and set the charging current (0.5A to 15A).

5.12. Synchronous Mode

In the settings menu, when the synchronization function is turned on, the M6D will allow two channels to charge the same battery with a total current of 25A.

M6D Charger in Synchronous Mode

Figure 5.1: M6D Charger in Synchronous Mode
This image illustrates the M6D charger operating in synchronous mode, with both channels connected to and charging a single battery.

6. Operating the Charger (Charge and Discharge Work)

When charging or discharging starts, the charger enters the working interface, displaying real-time information such as input voltage, current, power consumption, charger internal temperature, battery voltage, current, capacity, and individual cell voltages.

Rotate the [Scroll wheel] on this interface to switch between bottom status information and internal resistance/voltage values. Short press [OK] to dynamically set the working current or stop working.

To end the charge/discharge work, short press [OK], move the cursor to [Stop working], then short press [OK] again to stop work and return to the main interface.

If charging is completed or an error occurs, a prompt box will appear, and a tone will sound.

📄 Display Content Description:

  • Input Voltage (e.g., 24.00V): Input power supply voltage.
  • Input Current (e.g., 9A): Input power current.
  • Total Power Consumption (e.g., 20.0Wh): Total power consumed from the input.
  • Charger Internal Temperature (e.g., 45.0°C): Internal temperature of the charger.
  • Battery Voltage (e.g., 25.20V): Main port voltage of the second channel.
  • Battery Current (e.g., 10.00A): Main port current of the second channel.
  • Working Time (e.g., 060:59): Working time of the second channel.
  • Cumulative Capacity (e.g., 1888mAh): Cumulative capacity of the second channel.
  • Individual Cell Voltage (e.g., 4.202V): Voltage of the 1st battery cell.
  • Internal Resistance (e.g., 14mΩ): Internal resistance of the first battery.
  • Charge Done: Indicates the current charging status.
  • Lipo 6S: The current rechargeable battery type and number of cells.
  • 4.20V/2.00A: Current battery end voltage and charging current.

💡 Important Operating Tips:

  • When charging and discharging, directly supervise the process to deal with any abnormalities in time. Do not leave charging or discharging batteries unattended.
  • When charging and discharging lithium batteries, connecting only to the main port will not perform balance management. Connecting the balance lead is recommended for automatic balance management.
  • After charging is completed, unplug the battery. If continuous work mode is selected, connecting a new battery will automatically continue charging/discharging. Ensure batteries have the same cells and capacity. When using auto-detection, verify the detected number of cells matches the actual battery.

7. System Settings

After long-pressing [OK] on the main interface, you can enter the system setting interface when both channels are idle.

7.1. Input Power Settings

Enter the relevant settings for the power supply. After long-pressing, you can select power supply 1, power supply 2, and power supply 3. Short press to expand settings.

  • Power type: Battery and adapter (PSU). Battery can be used to recover energy in Recycle mode. Recycle mode cannot be used with a PSU or mains power adapter.
  • Max power: The maximum power absorbed from the input port when charging.
  • Max current: The maximum current drawn from the input port during charging.
  • Voltage range: The allowable input voltage range (7.0-28.0V).

7.2. Charging Security Settings

Short press to expand settings.

  • Safe Inter. Temp.: If the internal temperature exceeds this value, the device will stop the main port output.
  • Safe Exter. Temp.: If an external sensor detects a temperature higher than this value, the device will stop the main port output.
  • Safe time: The maximum time for continuous charge and discharge, beyond which it will stop working.
  • Safe capacity: The maximum capacity for continuous charge and discharge, beyond which it will stop working.

7.3. Other System Options

  • Synchronization mode: Can be set to open or not. When open, the two channels work synchronously, supporting more power.
  • Continuous work: When selected, the charger automatically continues with the same charging settings on the next connected battery. Ensure the next connected battery requires the same settings.
  • Work completed: After charging, choose whether to stop or trickle charge.
  • Backlight: Adjust the backlight brightness level of the display from 1 to 10.
  • Buzzer: Set the tone of the buzzer (can be turned off).
  • Language: Select the system display language (English, Chinese, etc.).
  • Default: Restore all settings to factory defaults.

8. Other Functions

8.1. Firmware Upgrade

Connect the M6D to your computer using the USB cable. The computer will recognize a USB disk named 'Toolkit'. Download the upgrade file (app.upg) from the official website, then copy and paste the new file to overwrite the previous files on the USB disk. The firmware will then be upgraded.

8.2. USB 5.0V Output

The USB interface can output 2.0A current to charge mobile devices, in addition to its firmware upgrade function.

8.3. Automatic Continuous Charge and Discharge

When a battery is fully charged, unplug it for 2 seconds, then connect the next battery. The device will automatically continue to charge and discharge. This function can be enabled/disabled in the menu (Continuous work mode).

8.4. Fan Level

The cooling fan operates based on internal temperature:

  • If the internal temperature exceeds 45°C, the fan turns on at half-speed airflow to reduce noise.
  • If the internal temperature exceeds 53°C, the fan turns on at full-speed airflow to enhance heat dissipation.

8.5. Manual Voltage Calibration

In the shutdown state, press and hold [Scroll Wheel] and do not release. Connect the power supply, and the system will enter the manual calibration voltage function. Measure the actual voltage of each battery with a voltmeter, then move the cursor to the corresponding voltage value and modify it to be consistent with the voltmeter value to achieve calibration. After calibration, move the cursor to 'save', short press once (the buzzer will beep), and the save is successful. Then log out or shut down.

8.6. Fully Charged Indication

When a lithium battery is charged, it prompts "Fast charging has ended". If the battery is not removed, constant voltage trickle charging will be performed automatically to make the battery more fully charged.

9. Specifications

FeatureSpecification
Input Voltage7-28V@MAX30A
Battery Type SupportedLiPo, LiHV, LiFe, Lion (1-6S); NiMh (1-16S); Pb (1-10S)
Balance Current800mA @2-6S
Voltage Accuracy<0.005V
Charging Power (Asynchronous)0.1-15A@250W *2
Charging Power (Synchronous)0.1-25A@500W
Discharging Power (Recycle Mode)0.1-15A@250W *2
Discharging Power (Normal Mode)0.1-3A@12W *2
USB Output2.1A@5V (upgrade@USB3.0)
Battery Voltage Range1.0V-5.0V @1-6S
Battery Internal Resistance1-100mΩ @1-6S
DisplayIPS 2.4 inch 320*240 resolution LCD
Product Size98mm*68mm*35mm
Product Weight220g
Individual Packing Size108.5mm*80.5mm*46mm
Individual Packing Weight300g

10. User Tips

  • Always double-check battery type and cell count settings before starting any charge or discharge cycle to prevent damage.
  • Utilize the balance port for all lithium-based batteries to ensure cell voltage equalization and prolong battery life.
  • Keep the charger in a well-ventilated area, especially during high-power operations, to assist the cooling fan.
  • Regularly check for firmware updates on the ToolkitRC website to ensure your charger has the latest features and performance improvements.
  • For NiMH batteries, experiment with PeakV settings within the recommended range to find the optimal value for your specific battery packs.

11. Troubleshooting

  • Charger not powering on: Ensure the input power supply is within the 7-28V range and correctly connected with proper polarity. Check the power source itself.
  • Error message on display: Refer to the specific error code or message displayed. Common errors relate to incorrect battery type/cell count, over-current, or over-temperature. Review your settings and connections.
  • Battery not charging/discharging: Verify that the battery is properly connected to the main port and balance port (if applicable). Check the selected mode (Charge, DisCHG, StoCHG) and current settings.
  • Charger overheating: Ensure adequate ventilation around the charger. Check if the cooling fan is operating. Reduce the charging/discharging current if the temperature remains high.
  • Inaccurate voltage readings: Consider performing a manual voltage calibration as described in section 8.5 if you suspect voltage inaccuracies.

12. Warranty and Support

For detailed warranty information and technical support, please refer to the official ToolkitRC website or contact your retailer.

A digital version of this user manual is available for download: ToolkitRC M6D User Manual PDF.

© ToolkitRC 2020

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.