AnyTone AT-5555N II

Contents

AnyTone AT-5555N II 10 Meter Radio

Model: AT-5555N II - Operating Instructions

1. Introduction

The AnyTone AT-5555N II is a high-performance 10-meter amateur radio mobile transceiver designed for reliable communication. This manual provides detailed instructions for the proper installation, operation, and maintenance of your radio. Please read this manual thoroughly before using the device to ensure optimal performance and safety.

AnyTone AT-5555N II radio with microphone, highlighting new features.
Figure 1: AnyTone AT-5555N II 10 Meter Radio with key features highlighted.

2. Package Contents

Before proceeding with installation, please check the contents of your package against the list below:

Image showing the package contents of the AnyTone AT-5555N II radio.
Figure 2: Contents included in the AnyTone AT-5555N II package.
  • AnyTone AT-5555N II (10 Meter Radio) x 1
  • Microphone x 1
  • Mounting Bracket x 1
  • DC Power Cable x 1
  • Replacement Fuse (15A) x 1
  • User Manual (English) x 1
  • Screws Set x 1

3. Functions & Features

The AT-5555N II is equipped with a comprehensive set of features for versatile operation:

  • Large LCD display with backlight dimming
  • AM/FM/USB/LSB/CW/PA modes
  • Frequency Tuning Steps: 100Hz/1KHz/5KHz/10KHz/100KHz/1MHz
  • ±500Hz/5KHz CLARIFIER Adjustment (R/T/R+T selectable)
  • Flexible Menu Functions and PC Programming Software
  • TX and RX Noise Reduction
  • VFO/BAND/Memory Channel modes
  • CTCSS/DCS with RX/TX Split functions
  • Enhanced VOX Functions (supports digital mode operation)
  • SQ, ASQ Function (FM and AM mode only)
  • RF GAIN Adjustment & RF PWR Adjustment
  • SCAN Function, NB/ANL Function
  • Repeater Shift/Offset Frequency Function
  • SIG/PWR/SWR Meter Functions
  • TOT Function, HI-CUT Function, SWR Protection, Power Supply Voltage Protection
  • WX weather channels with RX VFO mode (136-174MHz FM) & Weather Alert
  • Key-Lock Function, Model Name Customization Function
  • Compatible with electret and dynamic MIC types
  • ECHO Function, Programmable RB Function, Keypad BEEP Function, +10KHZ Function
  • DW Dual-Watch Function, EMG Channel Function

4. Getting Acquainted with Your Radio

4.1. Front Panel

Close-up of the AnyTone AT-5555N II radio's front panel and display.
Figure 3: Front panel view of the AT-5555N II.

The front panel houses all primary controls and the LCD display:

  • FRQ: Switch between channel mode and frequency mode / Offset setup.
  • BAND: Switch band: A-L-VFO / ECHO setup.
  • MENU: Menu Function key.
  • MODE: Switch mode (FM/AM/USB/LSB/CW/PA) / TSQ setup.
  • DW: Dual-watch scan / Frequency +10K function.
  • RB: RB function / Beep prompt function.
  • NB: NB function / HI-CUT function.
  • SCAN: Scan / Scan add / Scan delete.
  • MEM: Use, store or delete memory channels.
  • EMG: Emergency Channel / Keypad lock.
  • PWR: RF Power Control.
  • RFG: RF Gain Control.
  • SQ: Squelch Control.
  • CLAR: SSB/CW Clarifier Control.
  • VOL: Power On/Off; Volume Control.
  • CH: Channel Switch, CH Push key.
  • Microphone Jack: For connecting the supplied microphone.
  • LCD Display: Shows frequency, channel, mode, and status indicators.

4.2. Rear Panel

Rear view of the AnyTone AT-5555N II radio.
Figure 4: Rear panel view of the AT-5555N II.

The rear panel provides connections for antenna, power, and external accessories:

  • External SP Jack: For connecting an optional external speaker.
  • External PA Jack: For connecting an optional external public address speaker.
  • Antenna Jack: Standard UHF (SO239) connector for antenna.
  • Power Supply Jack: For connecting the DC power cable.
  • Programming Jack: For PC programming cable.

4.3. Microphone

The supplied microphone includes Channel Up/Down buttons and a PTT (Push-To-Talk) button for transmission.

4.4. LCD Display Indicators

The LCD display provides visual feedback on the radio's status, including signal strength, TX power, SWR, mode, frequency, channel number, and various function indicators (e.g., CTC, DCS, DW, NB, VOX).

5. Setup and Installation

5.1. Mounting the Radio

Choose a suitable location for mounting the radio, ensuring it does not obstruct the driver or passengers if installed in a vehicle. Use the provided mounting bracket and screws to secure the radio. Adjust the angle for optimal viewing and operation.

5.2. Microphone Connection

Insert the microphone connector into the microphone jack on the front panel until it clicks into place.

5.3. Antenna Installation

An efficient and resonant 50-ohm antenna is crucial for optimal performance. Screw the antenna connector into the antenna jack on the rear panel. Ensure the antenna system is properly grounded.

WARNING: Never transmit without a connected resonant antenna or a suitable 50-ohm load to prevent damage to the radio.

5.4. Power Connection

This radio requires a 13.8V (12V) DC power supply. Do not connect it to a 24V DC system.

  1. Connect the positive (red) power cable to the + terminal of your vehicle's battery.
  2. Connect the negative (black) power cable to the - terminal of the battery or a good chassis ground.
  3. Connect the DC power cable to the transceiver's power supply connector on the rear panel.

Ensure the power cable is routed away from high heat, moisture, and other electrical systems to prevent damage.

5.5. External Speaker (Optional)

If using an external speaker, choose an 8-ohm speaker with a 3.5mm mono plug. Plug it into the External SP Jack on the rear panel.

5.6. Replacing Fuses

The radio uses a 15A, 250V fuse. If the fuse blows, determine the cause, correct it, and replace the fuse with one of the same rating. Twist the two fuse covers in opposite directions to open the fuse holder.

6. Operating Your Radio

6.1. Basic Operation

  • Power ON/OFF: Turn the VOL knob clockwise to turn the radio ON, and anti-clockwise to turn it OFF.
  • Volume Control: Adjust the VOL knob to set the desired audio output level.
  • Channel Selection: In Channel Mode, turn the CH knob to select channels. Pressing the CH knob (PUSH) increases the channel step rate.
  • RF Power Control: Use the PWR control to adjust the TX output power for AM/FM/LSB/USB/CW modes.
  • RF Gain Control: Use the RFG control to adjust receiver sensitivity.
  • Squelch Control: Adjust the SQ control to eliminate background noise when no signal is present.
  • SSB Clarifier Control: Use the CLAR inner shaft to fine-tune the USB/LSB/CW TX or RX frequency.

6.2. Keypad Functions

The front panel buttons provide access to various functions:

  • MENU+MODE: Access WX Weather Channel mode.
  • FRQ/REP: Switch between Frequency and Channel display modes; long press for Offset Direction Function.
  • BAND/TONE: Select operating bands (A-L-VFO); long press for ECHO function.
  • MENU: Long press to enter the main Menu list.
  • MODE/TSQ: Select modulation mode (FM-AM-USB-LSB-CW-PA).
  • DW/+10K: Activate Dual-Watch scan; long press to enable +10KHz frequency shift.
  • RB/BEEP: Activate Roger Beep; long press for Beep Prompt function.
  • NB/HCUT: Activate Noise Blanker; long press for HI-CUT function.
  • SCAN/SKP: Start/stop scanning; long press to add/delete channels from scan list.
  • MEM/STOR: Enter Memory Channel mode; long press to store or delete memory channels.
  • EMG/LOCK: Access Emergency Channel (CH9/CH19); long press to lock/unlock keypad.

6.3. Background Function Menu Operation

The radio features an extensive menu system for advanced settings. To access:

  1. Press and hold the MENU button for 2 seconds.
  2. Turn the CH knob to select the desired menu item.
  3. Press the CH knob (PUSH) to enter the item setup.
  4. Turn the CH knob to select the desired setting.
  5. Press any other key or wait 5 seconds to save the setting.

Refer to the full PDF manual for a detailed list of all menu items and their functions (pages 16-18).

Video 1: Overview of the AnyTone AT-5555N II radio and its package contents.

7. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the radio's exterior. Do not use abrasive cleaners or solvents.
  • Antenna: Regularly check your antenna and its connections for corrosion or damage.
  • Power Cable: Inspect the power cable for any signs of wear or damage.
  • Environment: Avoid exposing the radio to extreme temperatures, direct sunlight, dust, or moisture.

8. Troubleshooting

If you experience issues with your radio, try the following:

  • No Power: Check the power cable connections and the fuse. Ensure the vehicle battery is charged.
  • No Audio: Check the volume level and ensure the squelch is not set too high. Verify external speaker connection if used.
  • Poor Reception/Transmission: Check antenna connection, SWR, and ensure the antenna is properly tuned for the operating frequency. Verify RF Gain and RF Power settings.
  • Radio Not Responding: Try turning the radio off and on. If issues persist, a factory reset (via menu option) might be necessary (note: this will erase custom settings).

9. Specifications

9.1. General

ParameterSpecification
Frequency Range28.000-29.700MHz (Programmable)
Frequency BandsA/B/C/D/E/F/G/H/I/J/K/L + VFO
Channels40 default channels in each band (up to 60 programmable)
Frequency ControlPhase-Locked-Loop Synthesizer
Frequency Step100Hz, 1KHz, 5KHz, 10KHz, 100KHz, 1MHz
Frequency Tolerance±5.00ppm
Temperature Range-20°C to +50°C
MicrophoneWith push-to-talk, UP/DN and coiled cord
Input Voltage13.8V DC
Dimensions (L x W x H)250mm x 200mm x 60mm
Weight1.5kg
Antenna ConnectorUHF, SO239

9.2. Transmitter

ParameterSpecification
Power OutputAM PEP: 60W / FM: 50W / SSB: 60W(PEP)
Current Drain10A maximum (with modulation)
ModulationAM/FM/USB/LSB/CW
Output Impedance50 ohms, unbalanced

9.3. Receiver

ParameterSpecification
Sensitivity (10dB S+N/N)SSB: 0.25µV, AM: 1.0µV, FM: 1.0µV (20dB S+N/N)
Image RejectionMore than 65dB
Audio Output Power3 watts into 8 ohms
Built-in Speaker8 ohms, round
Dimensional diagram of the AnyTone AT-5555N II radio.
Figure 5: Dimensions of the AnyTone AT-5555N II radio.

10. User Tips

  • Customization: The radio is highly customizable. Explore online resources for advanced programming and feature unlocking.
  • Performance: Ensure your antenna is well-tuned for the 10-meter band to achieve optimal transmission and reception.

11. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the documentation provided with your purchase or contact your retailer. You can also find additional resources and the full user manual in PDF format at the manufacturer's website or by downloading the provided PDF:

Download Full User Manual (PDF)

© 2024 AnyTone. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.