1. Introduction
Thank you for choosing the pecron E1000LFP Portable Power Station. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your device. Please read this manual thoroughly before using the product and keep it for future reference. For a downloadable PDF version of this manual, please refer to the official document here.
2. Safety Instructions and Warnings
Failure to follow these instructions may result in serious injury, death, or property damage.
2.1 General Warnings
- Do not place the device near heat sources such as fire or heating furnaces.
- Do not immerse in any liquid or expose the unit to rain or wet conditions.
- Do not use the battery in a strong static electricity or electromagnetic environment.
- Do not disassemble or puncture the product with sharp objects.
- Prevent short circuits caused by vermin, pests chewing through wires, or liquids contacting electrical wiring.
- This device is not intended to be used as a car jump starter; it can only be used to charge the car battery.
- Use only accessories or parts provided or approved by PECRON.
- Pay attention to the fact that the product is not waterproof. Prevent water from getting into it.
- Ensure good ventilation and heat dissipation during use. Maintain good airflow at the air inlet and outlet.
- Do not use the product in special occasions such as mines or gas stations.
2.2 Usage and Environmental Precautions
- Strictly follow the ambient temperature guidelines specified in this manual. Operating outside these temperatures can degrade performance, cause self-combustion, or lead to battery failure.
- Do not stack heavy objects on this product.
- Do not block the air vents during use. Avoid operating the device in non-ventilated or dusty spaces.
- Avoid impacts, falls, and violent vibration. Turn off the device immediately and stop using it if it experiences a major exterior impact. Fasten the unit firmly during transportation.
- If the device accidentally immerses in water, place it in a safe open area and keep away until it is completely dry. The dried unit should not be reused and must be disposed of properly according to local regulations.
- In case of fire, use recommended extinguishing equipment: water or mist, sand, fire blanket, dry chemical, or carbon dioxide fire extinguisher.
- Wipe the device surface with a dry cloth for cleaning.
- Handle this device with care to prevent damage from falling. If damaged by a fall, turn off the unit immediately, place it in an open area away from combustibles and crowds, and dispose of according to local laws.
- Store this device in a place out of reach of children and pets.
2.3 Disclaimer
Read this user manual thoroughly before use. PECRON is not responsible for any device damage or data loss resulting from failure to follow instructions. PECRON reserves the right to final explanation and to change terms and conditions without prior notice. Revisions will be posted on the official website.
3. Product Overview
3.1 Packing List
Before using your pecron E1000LFP, please check the package contents:
- pecron E1000LFP Portable Power Station x 1
- AC Cable x 1
- Single port XT60 to MC4 solar charging cable x 1
- Cigarette lighter male head to car charging cable XT60 x 1
- Accessory bag x 1
- User Instruction Manual x 1
(Diagram of packing list items typically shows the power station, various cables, and the accessory bag.)
3.2 Function Introduction (Ports and Controls)
The pecron E1000LFP features various ports and controls for versatile power management. Refer to the list below for a detailed description of each component:
- LCD Display: Shows operational status, battery level, input/output wattage, and other indicators.
- Main Switch: Powers the unit on/off.
- DC 11V~60V Charging Port: Input for solar panels or other DC sources.
- Adjustment Button of DC Charging Port: Adjusts the DC charging current.
- AC 100V~120V Output: Standard AC power outlets.
- DC 12V / USB Switch: Activates/deactivates DC 12V and USB outputs.
- AC 100V~120V Switch: Activates/deactivates AC outputs.
- DC12V Auxiliary Output: A 12V DC output port.
- DC12V(5525) Output: A 12V DC output port (5.5mm x 2.5mm barrel connector).
- DC12V XT60 Output: A 12V DC output port with an XT60 connector.
- USB-A / USB-C Ports: For charging USB-powered devices.
- External Grounding Port: For grounding the unit.
- AC 100V~120V Charging Port: Input for AC wall charging.
- Battery Expansion Port: For connecting an external expansion battery pack.
(Diagram of the unit's front and side panels typically illustrates these numbered components.)
4. Setup and First Use
Upon unpacking, ensure all items listed in the packing list are present and undamaged. It is recommended to fully charge the power station before its first use to optimize battery performance.
5. Operating Instructions
5.1 Basic Operation and Display
The E1000LFP is operated via its main switch and dedicated output switches. The LCD display provides real-time information about the unit's status.
- Power On/Off: Short press the Main Switch to turn on the unit. Long press to turn off. A short press while working will turn off the screen.
- DC/USB Output: Press and hold the DC 12V / USB Switch to turn DC/USB outputs on or off.
- AC Output: Press and hold the AC 100V~120V Switch to turn AC outputs on or off.
- Charging Current Adjustment: The charging current is adjustable during 12-30Vdc input. Ensure the AC function is turned off if there is no AC load on the unit when adjusting.
- WIFI Reset & Pairing: Long press both the AC 100V~120V Switch and the DC 12V / USB Switch simultaneously to reset WIFI and enter pairing mode.
- ECO Mode: Long press the Main Switch and the DC 12V / USB Switch simultaneously to activate ECO mode.
(Diagram of the unit's front panel with power buttons and display is typically shown here.)
5.1.1 LCD Display Details
The LCD display provides comprehensive information about the power station's operation:
- WIFI Connection Indicator
- Bluetooth Connection Indicator
- Current Switching Button of DC Charging
- ECO Mode Indicator
- Connection Of Expansion Battery Pack Indicator
- Battery Level Indicator
- UPS Function Indicator
- DC Output/Input Indicator
- AC Output/Input Indicator
- Fan Working Indicator
- AC/DC Input Wattage Display
- Equipment Alarm Indicator
- Temperature Alarm Indicator
- Timer Switch On Indicator
- Battery Heating Activated Indicator
- Battery Volume (Voltage) Display
- AC/DC Output Wattage Display
- Remaining Hours Of Charge/Discharge Display
(Diagram of the LCD display with numbered indicators and their descriptions is typically shown here.)
5.2 Charging the Power Station
5.2.1 AC Wall Charging
To charge the E1000LFP from a standard AC wall outlet:
- Connect the provided AC cable to the AC 100V~120V Charging Port on the power station.
- Plug the other end of the AC cable into a wall outlet (100Vac~120Vac 50/60HZ, 15A Max).
- The LCD display will show the charging status.
(Diagram showing the power station connected to a wall outlet via the AC cable is typically shown here.)
5.2.2 Vehicle Charging
You can charge the E1000LFP using your vehicle's cigarette lighter port:
- Connect the provided cigarette lighter male head to car charging cable (XT60) to the DC 11V~60V Charging Port on the power station.
- Plug the cigarette lighter end into your vehicle's 12V accessory socket.
- Attention: Do not adjust the charging current to 20A when using car charging, as standard car cigarette lighter plugs cannot safely handle 20A current.
(Diagram showing the power station connected to a car's cigarette lighter port is typically shown here.)
5.2.3 Storage Battery Charging
The E1000LFP can be charged from an external storage battery (requires additional purchase of specific spare parts):
- Connect the appropriate charging cable (e.g., XT90 to DC input) from the storage battery to the DC 11V~60V Charging Port on the power station.
- Adjust the charging current to 20A via the Adjustment Button of DC Charging Port if needed.
(Diagram showing the power station connected to a storage battery with positive and negative terminals is typically shown here.)
5.2.4 Solar Panel Charging
The E1000LFP can be charged using solar panels via the XT60 charging port.
- XT60 Charging Port Specifications: PV (operating voltage) range 11V~60V, 600W maximum. VOC (open circuit voltage) of solar panel/array must be less than 60V. Exceeding 60V will damage the unit.
- Do not wire more than two 36V solar panels in series, or more than four 18V solar panels in series. (18V/36V refers to Vmp of the solar panel).
- It is recommended to choose PECRON solar panels for optimal user experience. The VOC of a single solar panel should be less than 60V, and the VMP should be greater than 11V.
5.2.4.1 Charging with One Solar Panel
- Connect your solar panel to the provided single port XT60 to MC4 solar charging cable.
- Connect the XT60 end of the cable to the DC 11V~60V Charging Port on the power station.
(Diagram showing a single solar panel connected via an MC4 cable to the power station's DC input is typically shown here.)
5.2.4.2 Charging with Two Solar Panels in Parallel
To use two solar panels, you will need additional Y-branch MC4 charging cables (sold separately) to connect them in parallel.
- Connect each solar panel to its respective MC4 solar charging cable.
- Use Y-branch MC4 charging cables (one for positive, one for negative) to combine the outputs of the two solar panels in parallel.
- Connect the combined output to the DC 11V~60V Charging Port on the power station.
(Diagram showing two solar panels connected in parallel using Y-branch connectors to the power station's DC input is typically shown here.)
5.2.4.3 IMPORTANT: DO NOT WIRE TWO SOLAR PANELS IN SERIES!
Connecting solar panels in series can exceed the maximum input voltage (60V) of the XT60 port and will permanently damage the power station. The PV(XT60) Port only works within 12V~60V Open Circuit voltage.
(Diagram explicitly showing an incorrect series connection of two solar panels with a large 'X' over it is typically shown here.)
5.3 Using as an Uninterruptible Power Supply (UPS)
The E1000LFP supports UPS functionality, providing near-instantaneous protection (within 8~20ms) from unexpected power interruptions for connected loads.
- Compatibility: Not applicable to specific applications that require transfer time under 8ms (e.g., servers and workstations).
- Load Limit: This UPS function only supports protection for loads under 1800W (120V).
- Recommendation: To avoid overload and potential protection failure, connect only one device at a time when using UPS mode.
- PECRON is not responsible for any device damage or data loss resulting from failure to follow these instructions.
(Diagram showing the power station connected between a wall outlet and a computer for UPS functionality is typically shown here.)
5.4 Connecting an Expandable Battery
The E1000LFP can be expanded with an external battery pack (e.g., EP3000-48V) to increase capacity.
- Always use the official cascading cable with an MJ32 socket when connecting one expansion battery pack to avoid damage to the power station.
- Cascading will be faster if there is only approximately a 10% difference in charge level between the main power station and the expansion battery pack.
(Diagram showing the main power station stacked on top of an expansion battery pack, connected by a cascading cable, is typically shown here.)
6. Specifications
Below are the detailed technical specifications for the pecron E1000LFP Portable Power Station:
| Category | Specification |
|---|---|
| General Information | |
| Capacity | 1024Wh (51.2V 20Ah) |
| Battery Type | LiFePO4 (3500+ Cycles to 80%) |
| Net Weight | Around 29lb (13.5Kg) |
| Dimensions (L*W*H) | 14.9*9.4*10 in (378*239*255 mm) |
| Charge Temperature | 0°C~45°C / 32°F~113°F |
| Discharge Temperature | -20°C~45°C / -4°F~113°F |
| DC Output (Max 280W Total) | |
| USB-A (x2) | 5V, 9V, 12V, Max 18W each |
| USB-C (x2) | 5V, 9V, 12V, 20V, Max 100W each |
| XT60 Output (x1) | DC 12V-20A |
| Cigar Port (x1) | DC 12V-10A |
| DC 5525 Output (x1) | DC 12V-5A |
| AC Output | |
| BS-U20 (x5) | Pure Sine Wave 100V~120V, Rated 1800W Max, Peak 3000W |
| Input | |
| AC Inlet (x1) | 100Vac~120Vac 50/60HZ, 15A Max (1000W) |
| XT60 (x1) | 11V~60V, 600W Max, 20A Max (Solar/Car Input) |
| Extra Battery Port (MJ32) | 48V, 20A Max |
| Features | |
| Display Screen | Yes |
| Smart APP Control | Yes |
| Wifi Connect | Wifi remote control |
| Charging Time (AC) | 1.3 Hours |
(A table summarizing these specifications is typically shown in the manual.)
7. Maintenance
7.1 Cleaning
Wipe the surface of the device with a dry cloth. Do not use abrasive cleaners or immerse the unit in water.
7.2 Storage
For optimal battery life and safety:
- Turn off the unit before storing.
- Store in a dry, ventilated place at normal room temperature.
- Do not place the unit near water sources or in a wet/moist environment.
- For long-term storage, discharge the battery to 30% every three months and recharge it to 60% to sustain battery life.
8. Troubleshooting (FAQs)
- Q1: What kind of battery is used in E1000 LFP? How long can it last?
- A1: The E1000 LFP utilizes high-quality UL certified automotive LiFePO4 battery. It can retain 80% of its original capacity after 3500 complete charge cycles.
- Q2: What devices can E1000 LFP power?
- A2: The AC output port can power devices operating at less than 1800W. The DC output port can power devices operating at less than 12V-20A.
- Q3: Can the E1000 LFP be used as UPS?
- A3: Yes, the E1000 LFP supports UPS function with an automatic switchover time of 8~20ms.
- Q4: How to calculate the E1000 LFP running time?
- A4: Operation time = Battery Capacity (Wh) x DoD x η ÷ (Load Power + E1000 LFP Self-consumption). DoD (Depth of Discharge) is 95%. η (inverter conversion efficiency) is typically over 93%. Self-consumption is approximately 12W. For example, a 40W refrigerator can run for about 17 hours (1024Wh * 95% * 93% / (40W + 12W)). Actual times may vary based on usage conditions.
- Q5: Does E1000 LFP have a built-in MPPT charge controller?
- A5: Yes, it has one independent built-in MPPT controller. The "XT60" port supports 11~60V (Max 600W) PV input.
- Q6: Can the E1000 LFP be charged while discharging?
- A6: Yes, it can be charged and discharged simultaneously. In non-UPS state, if uninterrupted use is required, the average charging power must be greater than the average power consumption, otherwise the battery will eventually deplete.
- Q7: How to store the E1000 LFP?
- A7: Turn off the unit and store it in a dry, ventilated place at normal room temperature. Avoid water sources or wet environments. For long-term storage, discharge to 30% every three months and recharge to 60%.
9. Warranty and Support
9.1 Exclusions
PECRON's warranty does not apply to products that have been misused, abused, modified, damaged by accident, or used for anything other than normal consumer use as authorized in PECRON's current product literature.
9.2 Customer Support
For any inquiries, technical support, or warranty claims, please contact PECRON customer support:
- Email: support@pecron.com
- Website: www.pecron.com
10. Disposal
Proper disposal of the pecron E1000LFP is crucial due to its battery components. Batteries contain dangerous chemicals and must not be disposed of in ordinary trash.
- When conditions permit, completely discharge the battery of this product.
- Place the product in a designated battery recycling box. Follow local laws and regulations on battery recycling and disposal.
- If the battery cannot be completely discharged due to product failure, do not dispose of it directly. Contact a professional battery recycling company for further disposal.
- If the battery is over-discharged and cannot start, dispose of it according to proper disposal principles.
