STC STC12C5A60S2

Contents

STC12C5A60S2 Development Core Board User Manual

Model: STC12C5A60S2

1. Introduction

This manual provides instructions for the STC12C5A60S2 Development Core Board. This board is designed as a minimum system learning platform for 51 series microcontrollers, specifically featuring the STC12C5A60S2 MCU in an LQFP48 package. It includes dual serial ports, making it suitable for various embedded system development and learning applications.

STC12C5A60S2 Development Core Board with pin headers

Figure 1: STC12C5A60S2 Development Core Board with included pin headers.

2. Setup

Before using the development board, ensure you have the necessary tools and software, including a Micro-USB cable, a computer with a compatible IDE (Integrated Development Environment) for 51 series MCUs, and appropriate drivers for the USB-to-serial converter (if applicable).

2.1. Package Contents

  • STC12C5A60S2 Development Core Board
  • Pin headers (may require soldering for permanent connection)

2.2. Initial Connection

  1. Attach Pin Headers (Optional): If you intend to use the board on a breadboard or with jumper wires, solder the provided pin headers to the board's I/O ports. Ensure correct orientation.
  2. Power Connection: Connect one end of a Micro-USB cable to the Micro-USB port on the development board and the other end to a USB port on your computer or a 5V USB power adapter.
  3. Power On: Locate the power switch on the board (if present) and switch it to the 'ON' position. An LED indicator should illuminate, indicating power is supplied.
  4. Driver Installation: Your computer may require drivers for the onboard USB-to-serial converter. If prompted, install the necessary drivers. These are typically available from the chip manufacturer's website or the board vendor.
Angled view of the development board showing Micro-USB port

Figure 2: Angled view of the development board, highlighting the Micro-USB port for power and data.

3. Operating Instructions

The STC12C5A60S2 Development Core Board is primarily used for programming and testing 51 series microcontroller applications.

3.1. Programming the MCU

  1. Software Setup: Install a suitable IDE and compiler for 51 series microcontrollers (e.g., Keil uVision, SDCC).
  2. Code Development: Write your C or assembly code for the STC12C5A60S2 microcontroller.
  3. Compilation: Compile your code within the IDE to generate a HEX file.
  4. Flashing: Use the STC-ISP programming software (or similar tool) to upload the HEX file to the MCU via the USB-to-serial connection. Ensure the board is powered on and correctly connected. The STC microcontrollers typically support in-system programming (ISP) via their UART bootloader.

3.2. Using Dual Serial Ports

The board features dual serial ports (UARTs), which can be configured and used in your microcontroller program for communication with other devices, debugging, or data logging. Refer to the STC12C5A60S2 datasheet for detailed register configurations and usage of the UART peripherals.

4. Maintenance

  • Keep Dry: Protect the board from moisture and liquids to prevent short circuits and corrosion.
  • Cleanliness: Keep the board free from dust and debris. Use a soft, dry brush or compressed air for cleaning.
  • Static Protection: Handle the board by its edges and avoid touching the components directly, especially the pins of the ICs, to prevent damage from electrostatic discharge (ESD).
  • Inspect Connections: Periodically check soldered joints and pin header connections for any signs of damage or looseness.

5. Troubleshooting

ProblemPossible CauseSolution
Board does not power on (no LED)No power supply; faulty USB cable; power switch off.Check USB cable connection; try a different USB port/cable; ensure power switch is ON.
Cannot upload program to MCUIncorrect drivers; wrong COM port selected; MCU not in programming mode; faulty USB-to-serial chip.Install correct USB-to-serial drivers; select the correct COM port in ISP software; ensure board is powered; check ISP software settings.
Serial communication issuesIncorrect baud rate; wrong TX/RX connections; software configuration error.Verify baud rates match in software and hardware; check TX/RX pin connections; review microcontroller code for UART setup.

6. Specifications

FeatureDetail
MicrocontrollerSTC12C5A60S2 (51 series MCU)
PackageLQFP48
Serial PortsDual UART (Serial Ports)
Clock FrequencyMain crystal: 11.0592 MHz (visible on board)
Power Supply5V DC via Micro-USB port
Board VersionSTC89/STC12 DEMO BOARD V4.3
Dimensions (Approx.)Length: 14 cm, Width: 16 cm (packaging dimensions, for reference)
OriginMainland China
Close-up of STC12C5A60S2 microcontroller and 11.0592 MHz crystal

Figure 3: Close-up view of the STC12C5A60S2 microcontroller and the 11.0592 MHz crystal oscillator.

Bottom view of the development board showing version number

Figure 4: Bottom view of the development board, showing the board version "STC89/STC12 DEMO BOARD V4.3".

7. User Tips

Based on user feedback, those familiar with STC development boards generally find this board to be consistent with other STC products. While no specific operational tips were highlighted, ensuring proper driver installation and familiarizing oneself with the STC-ISP programming tool are common best practices for STC microcontrollers.

8. Warranty & Support

For warranty information and technical support, please refer to the seller or manufacturer's official documentation. If you encounter issues not covered in this manual, contact the vendor from whom you purchased the product.

A generic user manual PDF is available for reference, which provides general instructions for use in multiple languages. This PDF can be accessed at: User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.