IRALAN FX4-1

Contents

IRALAN LED Ceiling Chandelier Light User Manual

Model: FX4-1

Brand: IRALAN

Introduction

This manual provides detailed instructions for the assembly, operation, and maintenance of your IRALAN LED Ceiling Chandelier Light (Model: FX4-1). Please read this manual thoroughly before installation and use to ensure safe and correct operation.

IRALAN LED Ceiling Chandelier Light installed in a modern living room

Figure 1: IRALAN LED Ceiling Chandelier Light in a living room setting.

Safety Information

  • Ensure the power supply is disconnected before installation, cleaning, or maintenance.
  • Installation should be performed by a qualified electrician or in accordance with local electrical codes.
  • Do not modify the product in any way not described in this manual.
  • Keep the product away from water and high humidity environments.
  • Use only the specified voltage (90-260V AC).

Package Contents

Verify that all components are present and undamaged before proceeding with assembly.

  • Ceiling Plate
  • Light Panels (10 petals, varying sizes)
  • Short Tubes (7 pieces)
  • Long Tubes (3 pieces)
  • Nuts
  • Flat-headed Bolts
  • Wrench
  • Remote Control
  • Instruction Manual (this document)

Assembly Instructions

Follow these steps carefully for proper assembly. Refer to the assembly diagram below for visual guidance.

Assembly diagram for the LED Ceiling Chandelier showing 15 steps

Figure 2: Detailed assembly steps for the chandelier.

  1. Open the box and carefully remove all components.
  2. Place all components on a clean and flat surface.
  3. Assemble the 7 short tubes to their respective light panels. The short threaded end of the tubes goes into the panels.
  4. Assemble the 3 long tubes to their respective light panels. The short threaded end of the tubes goes into the panels.
  5. Assemble the panels with long tubes to the middle part of the ceiling plate.
  6. Secure these panels to the plate using nuts.
  7. Ensure all 3 panels with long tubes are firmly attached to the plate.
  8. Assemble the panels with short tubes to the marginal part of the ceiling plate.
  9. Secure these panels to the plate using nuts.
  10. Fasten all panels securely with the provided wrench.
  11. Connect all wires to the collector. Pay close attention to the correct direction; each wire has a minor ridge indicating the up side.
  12. Assemble the flat-headed bolts to the cross with nuts inside, but do not fully tighten them yet.
  13. Place the cross down, ensuring all bolts can pass through the four small holes on the plate. Then, remove the cross and fasten the nuts.
  14. Install the cross to the ceiling using sharp-pointed screws and an electric drill. Do not move the flat-headed bolts during this step.
  15. Lift the light fixture and install it onto the cross. The four flat-headed bolts should pass through the plate, and then fasten them with the nuts as shown.

Operation

Remote Control

The remote control allows for easy adjustment of your chandelier's settings. Pairing has been completed at the factory, so no additional operation is required for initial use.

Remote control for the LED Ceiling Chandelier with labeled buttons

Figure 3: Remote Control Layout and Functions.

  • Turn On/Off: Power button to switch the light on or off.
  • Brightness +/-: Adjust the light intensity.
  • Color Temperature +/-: Change the color temperature (e.g., from warm to cold white).
  • Full/Half Bright: Quickly switch between full brightness and half brightness.
  • Fully Bright: Sets the light to maximum brightness.
  • Night Light Function: Quickly switches to neutral light at 7% brightness, suitable for sleeping.
  • Sleep Mode: Activates a low-light setting.

APP Operation (LampSmart Pro)

Control your chandelier conveniently via the LampSmart Pro app on your smartphone.

  1. Download the APP: Scan the QR code below or search for "LampSmart Pro" in your app store. Open the browser and select the version to download.
  2. Open the APP: Select a room, click on the '+' icon, and enter the equipment name (e.g., "Living Room Light"). Click OK.
QR code for LampSmart Pro app download and dimming options

Figure 4: QR Code for LampSmart Pro App and Stepless Dimming illustration.

Pairing: To pair the light with the app, click the code matching button within 5 seconds of turning on the light. If the light source flashes or a "di" sound is heard, pairing is successful. If it fails, repeat the operation.

The app allows for various functions, including:

  • Setting a timer to turn off the device regularly.
  • Adjusting brightness:
    • White and yellow light simultaneously at 10% brightness.
    • White and yellow light simultaneously at maximum brightness.
    • Only yellow light at maximum brightness.
    • Only white light at maximum brightness.

Light Features Demonstration

Observe the dynamic lighting capabilities of your chandelier, including stepless dimming and color temperature adjustments.

Video 1: Demonstration of the chandelier's dimming and color temperature features.

Maintenance

  • Cleaning: Disconnect power before cleaning. Use a soft, dry cloth to wipe the fixture. Do not use abrasive cleaners or solvents, as they may damage the finish.
  • Bulb Replacement: This fixture uses integrated LED bulbs. Do not attempt to replace individual LEDs. If the light source fails, contact customer support.
  • Regular Checks: Periodically check all connections and mounting hardware to ensure they are secure.

Troubleshooting

ProblemPossible CauseSolution
Light does not turn on.No power supply; loose wiring; remote control battery low.Check power connection; ensure wiring is secure; replace remote control batteries.
Remote control or APP not responding.Remote battery low; pairing issue; APP not connected.Replace remote batteries; re-pair the device (see APP Operation); ensure APP is connected to the light.
Light flickers or dims unexpectedly.Unstable power supply; loose connection; internal fault.Check power source stability; verify wiring connections; contact customer support if problem persists.

Specifications

Dimensions and specifications of the LED Ceiling Chandelier

Figure 5: Product dimensions and lighting specifications.

FeatureDetail
Model NumberFX4-1
Brand NameIRALAN
Installation MethodAssembly, Surface mounted
Body MaterialIronware + Acrylic
MaterialAcryl
Light SourceLED bulbs (integrated)
Is DimmableYes
Switch TypeRemote Control
Voltage90 - 260 V AC
Luminous Flux2000-82000 LM (4000LM for 50W model)
Power50W (for D60cm model)
Lighting Area5-10 square meters (5-15m² for D60cm model)
Dimensions (D x H)60cm x 9cm (approx.)
Number of Light Sources> 20
Color Rendering Index (CRI)CRI 80+ (for White: 6000K)
CertificationsCCC, CE
Is Smart DeviceYes

User Tips

  • For optimal light distribution, ensure the chandelier is centered in the room.
  • Experiment with different color temperatures (warm, neutral, cold) to find the best ambiance for various activities or times of day.
  • Utilize the night light function for a soft, comfortable glow during evening hours.
  • If using the app, ensure your smartphone's Bluetooth is enabled and within range of the light fixture for stable connection.

Warranty and Support

This product comes with a 1-year warranty from the date of purchase. The warranty covers manufacturing defects and malfunctions under normal use. Please retain your proof of purchase for warranty claims.

For technical support, troubleshooting assistance, or warranty inquiries, please contact IRALAN customer service through your retailer or the official brand website.

A PDF version of this user manual is available for download: Download User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.