Preface
Thank you for purchasing the TrackerKing J16 4G GPS Tracker. This manual provides detailed instructions for operating the device smoothly and correctly. Please read this manual carefully before using the product. Note that specifications and information are subject to change without prior notice. Any updates will be integrated into the latest release. The manufacturer assumes no responsibility for any errors or omissions in this document.
1. Product Overview
The TrackerKing J16 is a 4G GPS tracker designed for real-time positioning and vehicle monitoring. It supports various functions including remote engine cut-off, geo-fencing, over-speed alarms, and more.

Image: TrackerKing J16 Multi-function Features Overview. This diagram illustrates key features such as Power Failure Alarm, Real-time Positioning, Mileage Statistics, Trace Playback, Remote Cut Engine, ACC Detection, Virtual Ignition Detection, Over-speed Alarm, Remote OTA, SOS Alarm (optional), Vibration Alarm, and Geo-fence Alarm.

Image: TrackerKing J16 4G GPS Tracker with Relay and Battery. This shows the main device, a 150mAh battery, and a relay, indicating the components included for certain configurations.
2. Setup and Installation
2.1 Preparation
- Open the package and verify that the device model number is correct and all accessories are present. If anything is missing or incorrect, please contact your supplier.
- Choose a suitable GSM SIM card. Refer to your supplier's suggestions for SIM card choice.
Important Notices for SIM Card:
- Please insert the SIM card before turning the device power switch ON.
- The SIM card must have GPRS function enabled.
- Ensure the SIM card has sufficient balance.
2.2 Quick Start Guide
- Insert SIM Card: Open the device case, carefully insert the GSM SIM card into the designated slot. Ensure the small switch inside the SIM card hole is turned ON.
- Connect Power: Connect the device to an external power supply according to the wiring diagram below.
- Initial Power On: Place the device outdoors. After approximately 30 seconds, three indicator lights will remain lit, indicating the device is working normally.

Image: TrackerKing J16 GPS Tracker SIM Card Slot. This view shows the internal layout of the device with the cover removed, highlighting the SIM card and TF card slots for proper insertion.
2.3 Installation Attentions
- Orientation: The device's front side must face the sky for optimal GPS signal reception.
- Placement: When installing in a car, be aware that windscreens with metal thermal insulation layers or heating layers can reduce the GPS signal strength, potentially leading to GPS malfunction.
Recommended installation locations within a vehicle:
- Under the front windshield
- Under the rear windshield
- Around the dashboard
2.4 Device Wiring Requirements
The following diagram illustrates the wiring connections for the TrackerKing J16 GPS tracker, including the relay for remote engine cut-off functionality.
Wiring Diagram Description:
- Red Wire: Connects to the positive terminal of the 9-80V vehicle battery, typically through a 2A FUSE.
- Black Wire: Connects to the negative terminal of the 9-80V vehicle battery (ground).
- Yellow Wire (from device): Connects to the ACC (Accessory) line of the vehicle, which provides power when the ignition is on.
- Relay Connections:
- The relay has four main terminals. Two terminals are for the coil (control circuit) and two are for the switch (power circuit).
- One terminal of the relay coil connects to the Orange wire from the device.
- The other terminal of the relay coil connects to the White wire from the device.
- The relay's switch terminals are used to interrupt the fuel pump (oil pump) or ignition circuit.
- One side of the fuel pump circuit (e.g., the positive supply to the fuel pump) is cut.
- The Yellow wire from the relay connects to one side of the cut fuel pump circuit.
- The Green wire from the relay connects to the other side of the cut fuel pump circuit.
- The relay itself is powered by the vehicle's 12/24V system.
Caution: Incorrect wiring can damage the device or vehicle. If you are unsure, please seek professional assistance.
3. Operating Instructions
3.1 Device Light Description
| Light Color | Represents |
|---|---|
| Yellow | GSM signal normal |
| Blue | GPS signal normal |
| Red | Power |
3.2 SMS Command List
The device can be configured and controlled using SMS commands sent from a registered mobile number to the SIM card number in the tracker. Ensure commands are typed exactly as shown.
| No. | Functional Item | SMS Command | Command Reply |
|---|---|---|---|
| 1 | Restore initial settings (except IP, port, APN) | FORMAT | FORMAT |
| 2 | APN query | APN# | Reply: APN:cmnet,, |
| 3 | APN set | APN,cmnet,,# APN,cmnet,aaa,bbb# | Command example: APN,cmnet,,# (Cmnet is APN, no user name/password) Example: APN,cmnet,internet,cmnet# (Cmnet is APN, internet is APN username, cmnet is APN password) |
| 4 | Server parameter query | SERVER# | Reply: SERVER:0,103.44.239.119,8011,0 |
| 5 | Server parameter settings | 1. Set domain name: SERVER,1,domain name,port,0# 2. Set IP: SERVER,0,IP,port,0# (Last 0 represents TCP) | SMS:SERVER,0,154.23.114.25,8011,0# Reply: SERVER:0,154.23.114.25,8011,0 |
| 6 | Address query (abroad) | URL# | <03-20 22:45>http://maps.google.com/maps?q=+22.601862,+113.832383 |
| 7 | Status query | STATUS# | Battery:4.23V;GPRS:Offline;GSMSignal Level:25;ACC:OFF;GPS:OFF;Defense:ON; |
| 8 | Query parameter settings | PARAM# | IMEI:123456781911111;TIMER:10,3600;SNEDS:3;HBT:180Sec;Defense:2; |
| 9 | Restart command | RESET# | Reply: RESET OK |
| 10 | Query oil/electricity control status | RELAY# | Reply: RELAY:0 |
| 11 | Oil/electricity control | RELAY,1# (disconnect) RELAY,0# (turn on) | Reply: RELAY 1 OK |
| 12 | Add center number 1 | CENTER,A,center number# | SMS: CENTER,A,8618575518750# Reply: CENTER,A:8618575518750 (86 is China country code) |
| 13 | Delete center number 1 | CENTER,D# | Reply: CENTER Del OK |
| 14 | Add center number 2 | CENTER,A2,center number# | SMS: CENTER,A2,8618007931238# Reply: CENTER,A2:8618007931238 |
| 15 | Delete center number 2 | CENTER,D2# | Reply: CENTER D2 Del OK |
| 16 | Add center number 3 | CENTER,A3,center number# | SMS: CENTER,A3,8613912345678# Reply: CENTER,A3:8613912345678 |
| 17 | Delete center number 3 | CENTER,D2# | Reply: CENTER D3 Del OK |
| 18 | Query center number | CENTER# | Reply: CENTER,A:8618575518750 CENTER,A2:8618007931238 CENTER,A3:8613912345678 |
| 19 | Add SOS number | SOS,A,number 1,number 2,number 3# | SOS,A,8618575518750# SOS,A,8613912345678,8618007931238# SOS,A,8613912345678,8613912345678,8613912345678# Option to set 1 or more numbers at a time |
| 20 | Delete SOS number | SOS,D,number 1,number 2,number 3# | SOS,D,1# SOS,D,1,2# SOS,D,1,2,3# Option to delete 1 or more numbers at a time |
| 21 | Query SOS number | SOS# | Reply: SOS:8613912345678,8613912345678,8613912345678 |
| 22 | Allow auto answering | 777# | Reply:Automatic incoming call answering has been set After setting, the device will answer the call automatically after any number |
| 23 | Disable automatic answering | 888# | Reply: Automatic incoming call answering has been Close After setting, the device will answer the call automatically after SOS or center number (default: forbidden) |
| 24 | Set incoming call function | SZCS#CALL_FUN=A | A=0 voice monitoring function after incoming calls (default, needs device support microphone) A=1 reply to google link after incoming call SMS: SZCS#CALL_FUN=1 Reply: SETOK: CALL_FUN=1 |
| 25 | Query incoming call function | CXCS#CALL_FUN | Reply: READOK: CALL_FUN=1 |
| 26 | Heartbeat packet setting interval | HBT,T1,T2# T1=60-300s (ACC ON) T2=60-300min (ACC OFF) | SMS:HBT,180,180# Reply: HBT ACC ON:180s,ACC OFF:180s |
| 27 | Query heartbeat packet interval time | HBT# | Reply:HBT ACC ON:180s,ACC OFF:180s |
| 28 | Set GPS data timing sending interval | TIMER,T1,T2# T1=5-60s (ACC ON) T2=5-1800s (ACC OFF) | SMS: TIMER,30,300# Reply: TIMER ACC ON:30s,ACC OFF:300s |
| 29 | Query GPS data timing sending interval time | TIMER# | Reply: TIMER ACC ON:30s,ACC OFF:300s |
| 30 | Turn on vibration alarm settings | SENALM,A,M# (A=ON) M=0-2 (0=GPRS, 1=SMS+GPRS, 2=GPRS+SMS+CALL) | SMS: SENALM,ON,2# Reply: SENALM:ON,2 |
| 31 | Turn off vibration alarm settings | SENALM,OFF# | Reply: SENALM:OFF |
| 32 | Query vibration alarm setting parameters | SENALM# | Reply: SENALM:OFF |
| 33 | Enable power-off alarm settings | POWERALM,A,M,T1,T2,# (A=ON) M=0-2; T1=5-60s (detection time); T2=1-3600s (min charging time) | SMS: POWERALM,ON,2,10,10,# Reply: POWERALM:ON,2,10,10 |
| 34 | Turn off power-off alarm | POWERALM,OFF# | Reply: POWERALM:OFF |
| 35 | Query power-off alarm status | POWERALM# | Reply: POWERALM:ON,2,10,10 |
| 36 | Enable low battery alarm settings | BATALM,A,M# (A=ON) | SMS: BATALM,ON,1# Reply: BATALM:ON,1 |
| 37 | Turn off low battery alarm settings | BATALM,OFF# | Reply: BATALM:OFF |
| 38 | Query low battery alarm status | BATALM# | Reply: BATALM:ON,1 |
| 39 | Enable movement alarm settings | MOVING,A,R,M# (A=ON) R=100-1000 (movement radius) M=0-2 | SMS: MOVING,ON,1000,2# Reply: MOVING:ON,1000,2 |
| 40 | Turn off movement alarm | MOVING,OFF# | Reply: MOVING:OFF |
| 41 | Query movement setting status | MOVING# | Reply: MOVING:ON,1000,2 |
| 42 | Turn on overspeed alarm | SPEED,A,B,C,M# (A=ON) B=5-600s (overspeed time) C=1-255km/h (speed setting) M=0-1 | SMS: SPEED,ON,10,120,1# Reply: SPEED:ON,10,120,1 |
| 43 | Turn off over speed alarm | SPEED,OFF# | Reply: SPEED:OFF |
| 44 | Query overspeed setting status | SPEED# | Reply: SPEED:ON,10,120,1 |
| 45 | Turn on ACC ignition on alarm | ACCALM,A,M# (A=ON) M=0-3 | SMS: ACCALM,ON,3# Reply: ACCALM:3,OK |
| 46 | Turn off ACC ignition on alarm | ACCALM,OFF# | Reply: ACCALM,OFF OK |
| 47 | Query ACC ignition on alarm | ACCALM# | Reply: ACCALM:3,OK |
| 48 | Turn on ACC off alarm | ACCOFFALM,A,M# (A=ON) M=0-3 | SMS: ACCOFFALM,ON,3# Reply: ACCOFFALM:3,OK |
| 49 | Turn off ACC off alarm | ACCOFFALM,OFF# | Reply: ACCOFFALM,OFF OK |
| 50 | Query ACC off alarm | ACCOFFALM# | Reply: ACCOFFALM:3,OK |
| 51 | Query sleep working mode | CXCS#SLPDISCONNECT | Reply: READOK: SLPDISCONNECT=0 |
| 52 | SMS time zone settings | GMT,A,B,C# A: E or W ("E" eastern, "W" western) B: 0-12 (time zone default: 8) C: 0/15/30/45 (half time zone default: 0) | SMS: GMT,E,8,0# Reply: GMT:E,8,0 |
| 53 | SMS time zone query | GMT# | Reply: GMT:E,8,0 |
3.3 Web Platform and Mobile App
For further details and advanced tracking features, you can use the web-based platform or the mobile application:
- Web Platform: Visit www.trackerking.net.
- Mobile App: Search for "Tracker King" in the Google Play Store (for Android) or your device's APP store (for iOS).
4. Maintenance
To ensure the longevity and optimal performance of your TrackerKing J16 GPS Tracker, follow these general maintenance guidelines:
- Keep Clean: Regularly wipe the device with a dry, soft cloth. Avoid using harsh chemicals or solvents.
- Avoid Extreme Conditions: Do not expose the device to extreme temperatures (hot or cold), high humidity, or direct water contact.
- Secure Connections: Periodically check all wiring connections to ensure they are secure and free from corrosion.
- Software Updates: Keep the device firmware updated if new versions are released (often managed via the platform or OTA).
5. Troubleshooting
If you encounter issues with your TrackerKing J16, consider the following troubleshooting steps:
- No Signal (GPS/GSM):
- Ensure the device is installed with the front side facing the sky and has a clear view of the sky.
- Check SIM card insertion and ensure it has GPRS enabled and sufficient balance.
- Verify the SIM card is active and has network coverage in the area.
- Check device lights: Yellow (GSM), Blue (GPS). If not lit or blinking abnormally, there might be a signal issue.
- Device Not Responding to SMS:
- Confirm the SIM card in the tracker has credit and is receiving messages.
- Ensure the SMS commands are typed exactly as specified in the manual (case-sensitive, correct punctuation).
- Verify the sending phone number is authorized (if center numbers are set).
- Inaccurate Positioning:
- Ensure the device is in an open area. GPS accuracy can be affected by buildings, tunnels, or dense foliage.
- Check for any metallic obstructions near the device that might interfere with GPS signals.
- Remote Engine Cut-off Not Working:
- Verify the relay wiring is correct and secure.
- Ensure the vehicle's ignition is off before attempting to cut off the engine remotely.
- Check the device's power supply and GSM signal.
- Device Not Powering On:
- Check all power connections (Red and Black wires) to the vehicle battery.
- Ensure the vehicle battery has sufficient charge.
- Verify the 2A fuse is intact.
- Reset Device: If the device is unresponsive, try sending the `RESET#` SMS command.
6. Specifications
Detailed technical specifications for the TrackerKing J16 4G GPS Tracker:

Image: TrackerKing J16 Product Parameters and Specifications. This table provides a comprehensive list of technical details for the device.
| Specification Content | Specifications |
|---|---|
| Product Name | 4G Positioner |
| Overall Dimension | 80*39*17mm |
| Product Weight | 49.1g (including battery) |
| Positioning Method | GPS+BEIDOU+LBS |
| Positioning Accuracy | 3-30 (m) |
| Working Temperature | -20°C to +60°C |
| Storage Temperature | -20°C to +70°C |
| Battery Capacity | 150mAh (3.7V) |
| Communication Module Brand | SIMCOM-A7670SA |
| Positioning Module Brand | A7670SA/HEXINGTONGUC6228CI |
| Tracking Sensitivity | -159dbm |
| Capture Sensitivity | -144dbm |
| Frequency Band | LTE - FDD:B1/B3/B5/B8 LTE - TDD:B34/B38/B39/B40/B41 |
| Network | 4G+2G network |
| Band (LTE-FDD) | B1/B2/B3/B4/B5/B7/B8/B28/B66 |
| Band (GSM) | 850/900/1800/1900MHz |
| GPS Chip | SIMCOM |
| GSM Module | SIMCOM7670SA |
| GPS Accuracy | 5m |
| Time To First Fix (Cold) | 45s |
| Time To First Fix (Warm) | 35s |
| Time To First Fix (Hot) | 1s |
| Work Voltage | 9V-80V |
7. User Tips
Here are some tips to enhance your experience with the TrackerKing J16:
- Regularly Check SIM Balance: Ensure your SIM card always has sufficient credit to send data and SMS commands, especially for critical alerts.
- Test Alarms: Periodically test features like geo-fence, over-speed, and vibration alarms to ensure they are configured correctly and functioning as expected.
- Secure Installation: For vehicle tracking, consider discreet installation locations to prevent tampering or easy removal.
- Power Source Stability: Ensure the device is connected to a stable power source in the vehicle to avoid unexpected shutdowns or data loss.
8. Warranty and Support
For warranty information, technical support, or further inquiries, please contact your original seller or the manufacturer.
You can also refer to the official user manual PDF for additional details: Download User Manual (PDF)
For online support and platform access, visit www.trackerking.net or use the "Tracker King" mobile application.