TECTINTER For switch/oled

Contents

TECTINTER Vertical Bracket Grip for Nintendo Switch/OLED

Instruction Manual

Introduction

Thank you for choosing the TECTINTER Vertical Bracket Grip. This accessory is designed to enhance your gaming experience on the Nintendo Switch and Nintendo Switch OLED models by providing a comfortable and secure vertical orientation for gameplay. Please read this manual carefully before use to ensure proper installation and operation.

Safety Information

WARNING:

  • Choking Hazard: Small parts. Not suitable for children under 3 years.
  • Device Security: Ensure your console and Joy-Con controllers are securely attached to the grip to prevent accidental drops.
  • Heat: Do not block any vents on your console while using the grip. Avoid prolonged exposure to extreme heat or direct sunlight.
  • Force: Do not use excessive force when attaching or detaching your console and controllers to avoid damage to the grip or your devices.

Compatibility

This Vertical Bracket Grip is compatible with the following Nintendo Switch models:

  • Nintendo Switch (Standard Model)
  • Nintendo Switch OLED Model

Note: This product is NOT compatible with the Nintendo Switch Lite.

Compatibility chart showing Nintendo Switch and Switch OLED are compatible, while Switch Lite is not.
Figure 1: Compatibility Overview

Setup and Installation

Follow these steps to properly install your Nintendo Switch or Switch OLED into the Vertical Bracket Grip:

  1. Detach Joy-Cons: Before inserting the console, ensure both Joy-Con controllers are detached from your Nintendo Switch/OLED console.
  2. Align Console: Orient your Nintendo Switch/OLED console so that its charging port is facing the same direction as the fixing tabs inside the central slot of the grip.
  3. Slide Console In: Gently slide your console downwards into the central grip slot until it is securely seated. Ensure it clicks into place or feels firm.
  4. Attach Joy-Cons: Slide your left Joy-Con onto the left side rail of the bracket and your right Joy-Con onto the right side rail until they click into place.
Diagram showing step-by-step installation and detachment of the Nintendo Switch console and Joy-Cons into the vertical grip.
Figure 2: Installation and Detachment Steps

Video Guide:

Video 1: Product Installation and Usage Demonstration

Operating Instructions

Using the Grip:

Once your console and Joy-Cons are securely attached, you can hold the grip comfortably for vertical gameplay. The design allows for an ergonomic hold, especially beneficial for games that support vertical screen orientation.

Detaching the Console and Joy-Cons:

  1. Detach Joy-Cons: Press the small release button on the back of each Joy-Con controller and slide them upwards off the side rails of the grip.
  2. Remove Console: Gently push the console upwards from the bottom of the grip, then pull it out completely from the central slot.

Maintenance

To ensure the longevity of your Vertical Bracket Grip:

  • Cleaning: Wipe the grip with a soft, dry cloth. Do not use abrasive cleaners or solvents, as they may damage the material.
  • Storage: Store the grip in a cool, dry place away from direct sunlight and extreme temperatures when not in use.

Troubleshooting

  • Console does not fit: Ensure you are using a compatible Nintendo Switch or Switch OLED model. The grip is not designed for the Switch Lite. Verify the console is aligned correctly before sliding it in.
  • Joy-Cons not responding: If your Joy-Cons are attached to the grip but not responding, ensure your Nintendo Switch is not in Airplane Mode. Airplane Mode can disable wireless communication with detached Joy-Cons.
  • Grip feels loose: Double-check that the console and Joy-Cons are fully inserted and clicked into their respective slots. The grip is designed for a secure fit.

Specifications

FeatureDetail
BrandTECTINTER
Model NumberFor switch/oled
MaterialABS
Compatible ModelsNintendo Switch, Nintendo Switch OLED
Accessory TypeController holder
USB ConnectivityNo
Package Dimensions (L x W x H)19 cm x 19 cm x 4 cm
Package Weight0.077 kg
OriginMainland China

User Tips

  • For optimal Joy-Con functionality when detached, ensure your Nintendo Switch is not in Airplane Mode.
  • The secure fit of this grip makes it ideal for action-oriented games, including shooters, where a firm hold is beneficial.
  • The grip is designed to fit both the standard Nintendo Switch and the OLED model well, providing a stable platform for vertical play.

Warranty and Support

For any questions, concerns, or support regarding your TECTINTER Vertical Bracket Grip, please contact the seller directly through your purchase platform. Please refer to your purchase details for specific warranty information.

© 2024 TECTINTER. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.