1. Introduction
Thank you for purchasing the M8D balance charger. Please read this manual carefully before use to ensure proper operation and longevity of your device.
The ToolkitRC M8D is a touch screen balanced charger product with a total charging power of up to 1600W. It features an IPS bright display and a combination of capacitive touch screen and roller encoder for convenient operation.
Figure 1: ToolkitRC M8D Intelligent Charger with accessories.
Key Points
- Tips: Helpful advice for optimal use.
- Important: Critical information to prevent damage or ensure safety.
- Information: General details and explanations.
Further Information
To ensure you have the best experience with this product, visit www.toolkitrc.com for news, information, and firmware updates. A detailed user manual (PDF) is also available for download: M8D Manual V1.0 (PDF).
2. Safety Instructions
Failure to follow these safety instructions may result in fire, property damage, or injury.
- The M8D allows an input voltage of DC 10.0V-49.0V. To ensure the power supply voltage is consistent, pay attention to the positive and negative polarity of the power supply before use.
- Do not use this product in hot or humid environments. Keep away from flammable liquids and gases.
- Never leave charging batteries unattended.
- When not in use, please turn off/unplug the device.
- When using the charging function, please set a current that matches the battery performance envelope. Do not set an excessive current for charging to avoid damage to the battery. Check the guidelines of your battery's manufacturer for correct charging instructions.
- Choosing the wrong battery type for charging may damage the battery, charger, burn, and other dangers. Please be sure to choose carefully.
- Do not charge batteries that are not labeled with a battery type.
- Lixx batteries can be identified more accurately when they are connected to the balance port.
3. M8D Layout
Familiarize yourself with the components and ports of your M8D charger.
Figure 2: Front view of the M8D Charger.
- Display/Touch panel: Main interface for operation and information display.
- CH/Exit: Button to exit menus or switch channels.
- Scroll wheel: Used for navigation and value adjustment.
- Main port*2: Two main XT60 output ports for charging/discharging.
- Balance port*2: Two balance ports for 2-8S batteries, essential for balanced charging of lithium batteries.
Figure 3: Back view of the M8D Charger.
- DC input XT90: Main power input port (DC 10-49V).
- USB A/C output: USB Type-C port for fast charging external devices (up to 65W).
- Cooling fan: Internal fans for heat dissipation during operation.
4. Quick Start Guide
- Connect Power: Connect the M8D device to a DC 10-49V power source using the XT90 input port.
- Boot Sequence: The screen will show the boot logo for 2 seconds, accompanied by an audible tone.
- Main Interface: After booting, the screen enters the main interface, displaying real-time charging information.
- Navigation: Touch the main interface or use the [Scroll Wheel] to select the desired function. Press the [Scroll Wheel] to confirm.
- System Settings: Touch the [Settings icon] (
) or press and hold the [Scroll Wheel] to enter system settings. - Information Display: Touch the [Info] button or scroll the [Scroll Wheel] to select it to display voltage and internal resistance for the corresponding channel.
- Charging Task Management: Touch [Status] or short press [Scroll Wheel] to select [Status] to manage the charging task when a channel is idle. You can adjust and end the task while the channel is working.
- Exit: Press the [Exit Button] to end modifications or return to the previous interface.
General Operation Tips:
- A short press of the [Scroll Wheel] confirms a function.
- A long press (2 seconds) of the [Scroll Wheel] activates the delete key function.
- Successful key operations are accompanied by an audible 'didi' sound.
5. Charging Settings
From the main interface, select and short press the [Scroll Wheel] to enter the charging function. If "Battery selection" is enabled in system settings, you can choose from 10 saved battery records. Otherwise, it defaults to the first record.
Figure 4: Main charging interface.
5.1. Battery Type Selection
The charger supports 7 types of batteries: LiPo, LiHV, LiFe, Lion, LTO, NiMH, and PB. Select the appropriate type to match your battery. Press [Confirm] to apply changes.
- LiPo: Lithium Polymer (Nominal 3.70V, Full 4.20V)
- LiHV: High-Voltage Lithium (Nominal 3.85V, Full 4.35V)
- LiFe: Lithium Iron (Nominal 3.30V, Full 3.60V)
- Lion: Lithium-Ion (Nominal 3.60V, Full 4.10V)
- LTO: Lithium-Titanate (Nominal 2.40V, Full 2.70V)
- NiMh: Nickel-Metal Hydride (Nominal 1.20V)
- PB: Lead-Acid (Nominal 2.00V)
Important: Choosing the wrong battery type can severely damage the battery and charger.
5.2. Number of Cells
Modify the number of battery cells. When set to [Auto], the charger automatically identifies the number of strings based on the connected battery's voltage. Press [Confirm] to apply.
- Tips: If a battery is over-discharged or overcharged, the auto-detection might be inaccurate. Manually set the correct number of strings in such cases. Incorrect cell count settings can prevent charging or cause damage.
5.3. Mode Selection
Select the desired work mode:
- Charge: Standard charging mode.
- Discharge: Discharges the battery.
- Cycle: Cycles the battery through charge/discharge.
- Destroy: Completely drains the battery's voltage for safe disposal. Warning: This causes irreversible damage and should only be used for battery disposal, not normal use.
5.4. End Voltage Setting (TVC)
TVC (Terminal Voltage Control) allows you to modify the end voltage of a monolithic battery. For charging, it's the cut-off voltage (range ±50mV of full voltage). For discharging, it's the discharge cut-off voltage. Adjustment step is 0.01V.
- Only LiPo, LiHV, LiFe batteries can set the cut-off voltage.
- Do not modify the cut-off voltage if you are unfamiliar with battery characteristics.
5.5. Charging Current
Adjust the charging current using the [Slider] or [Scroll Wheel] in 0.1A steps. Scrolling quickly increases/decreases faster. The charger supports up to 30A.
- Tips: Set the charging rate to 1-2C according to battery capacity. For example, a 2000mAh battery should be charged at 2.0-4.0A. Always refer to your battery manufacturer's guidelines.
5.6. NiMh Setting (PeakV)
For NiMh batteries, you can set the PeakV value (3mV-15mV). PeakV refers to the voltage drop peak value of each cell when the NiMH battery is fully charged.
6. Charging Process
Once charging begins, the charger enters the working interface, displaying real-time data.
Figure 5: M8D Charger in operation, connected to a power supply.
Select the [Info] button to view the voltage value of the corresponding channel. Slide the voltage information to the left to switch to the internal resistance display.
Figure 6: Internal resistance display on M8D screen.
Select [Status Bar] to dynamically set the working current or stop the operation.
Display Content Description:
- Input Supply Voltage (e.g., 24.0V): Voltage from the external power source.
- Input Supply Current (e.g., 14.8A): Current drawn from the external power source.
- Cumulative Power Consumption (e.g., 20Wh): Total power consumed from the input.
- Internal Temperature (e.g., 45°C): Temperature of the charger.
- Main Port Voltage (e.g., 32.23V): Voltage of the main port for the first channel.
- Main Port Current (e.g., 5.00A): Current of the main port for the first channel.
- Working Hours (e.g., 10:59): Duration of operation for the first channel.
- Cumulative Capacity (e.g., 2000mAh): Total capacity charged/discharged for the first channel.
- Battery Voltage (e.g., 4.200V): Voltage of an individual battery cell. Red mark indicates balance management.
- Internal Resistance (e.g., 5.2mΩ): Internal resistance of an individual battery cell.
Tips: When charging, always supervise the process to safely handle any abnormalities.
When charging a lithium battery, connecting only to the main port will not perform balance management. Always connect to the balance port for automatic balance management.
After charging is complete, unplug the battery. If you insert a new battery, it will automatically continue to charge/discharge according to the set mode. Ensure that batteries with the same number of cells are connected when a fixed cell count is set. When using auto-detection, verify the detected cell number matches the actual number.
7. System Settings
Access system settings by selecting the [Settings icon] on the main interface or by pressing and holding the scroll wheel for 2 seconds when both channels are idle.
7.1. Input Settings
- Input Power (P1, P2, P3): Save and select up to 3 input power profiles (power, current, voltage).
- Power Type: Defines the type of input power supply. Discharge recycling is only available when the input is set to 'Battery'.
- Power on selection: If enabled, the charger prompts you to select a power profile upon startup.
- Max power: Maximum power absorbed from the input port during charging.
- Max current: Maximum current drawn from the input port during charging.
- Min voltage: Lowest allowable input voltage.
7.2. Charging Safety Settings
- Safe Inter temp.: Device stops main port output if internal temperature exceeds this value (e.g., 80°C).
- Safe Exter temp.: Device stops main port output if external temperature exceeds this value (e.g., 50°C).
- Safe time: Maximum continuous charging time. Charging stops if exceeded (e.g., 200 Min).
- Safe capacity: Maximum capacity for continuous charging. Charging stops if exceeded (e.g., 30Ah).
- Synchronous mode: Combines both channels to charge the same battery with a maximum current of 50A.
- Continuous Operation: If enabled, after a battery is fully charged and removed, connecting the next battery automatically starts charging with the previous settings.
- Work completed: Determines whether to stop or trickle charge when charging is complete.
- Battery selection: If enabled, allows saving and selecting battery profiles.
- Balance start voltage: Sets the voltage at which battery balancing begins relative to the full voltage.
7.3. General System Settings
- Backlight: Adjusts display brightness (1-10 levels).
- Sound Volume: Sets the speaker volume (high, medium, low, off).
- Language: Changes the system display language (11 options available).
- Theme style: Selects between Light and Dark display themes.
- SD-log: Configures logging interval settings.
- Manual Calibration: Calibrates voltage values for both channels if the display deviates from actual battery voltage.
- Default: Restores all settings to factory values.
- ID: Displays the unique device ID.
8. Other Functions
8.1. Firmware Upgrade
Connect the M8D to your computer via the included USB data cable. The computer will recognize a USB drive named "Toolkit". Download the upgrade file (app.upga) from the official website, copy it to the USB drive, and overwrite existing files to upgrade the firmware.
8.2. Automatically Continue Charging
When a battery is fully charged, unplug it and connect the next battery. The device will automatically continue charging. This function can be enabled or disabled in the settings menu.
8.3. Fan Stepless Speed Regulation
When the internal temperature exceeds 43°C, the fan speed increases linearly with temperature or power increase, reducing noise during low-temperature or low-power operation.
8.4. USB Fast Charging
The M8D has a built-in USB fast charging protocol, supporting up to 65W charging power via the Type-C port. Supported protocols include PD, QC, AFC, FCP, SCP, PE, SFCP, VOC.
8.5. Manually Calibrate Voltage
In system settings, access the manual voltage calibration function. Use a voltmeter to measure the actual voltage of each battery. Adjust the displayed voltage value to match the voltmeter reading. After calibration, save the settings.
8.6. Fully Charged Replenishment
When a lithium battery is charged, the device prompts "Fast charging has ended". If the battery is not removed, it will automatically trickle charge at a constant voltage to bring the battery to a fuller state.
8.7. Battery Destruction
This function completely drains a lithium battery's voltage for safe disposal, preventing combustion risk from residual voltage. Warning: This function causes irreversible damage and should only be used for battery disposal, not normal use.
9. Specifications
| Feature | Specification |
|---|---|
| Input Voltage | DC 10.0-49.0V @MAX 60A |
| Supported Battery Types | LiPo, LiHV, LiFe, Lion LTO (1-8S); NiMh (1-20S); Pb (1-15S) |
| Balance Current | 2000mA @2-8S |
| Accuracy | <0.005V |
| Charge Power (ASYN) | 0.1-30.0A @800W*2 |
| Charge Power (SYNC) | 0.1-50.0A @1600W*2 |
| Discharge Power (Recycle) | 0.1-30.0A @800W*2 |
| Discharge Power (Normal) | 0.1-10A @40W*2 |
| USB Output | USB-C 20V@65W (PD, QC, AFC, FCP, SCP, PE, SFCP, VOC) |
| Battery Voltage Range | 1.0V-5.0V @1-8S |
| Battery Internal Resistance | 1-100mΩ @1-8S |
| LCD Display | IPS 3.5 inch 480*320 Pixel |
| Touch Panel | Capacitive |
| Product Size | 130mm * 97mm * 42mm |
| Product Weight | 450g |
| Individual Packing Size | 140mm * 110mm * 500mm |
| Packing Weight | 700g |
10. User Tips
- Synchronized Storage Mode: Exercise caution when using synchronized storage mode. Always refer to the manual for detailed instructions to prevent accidental damage.
- User Interface: The M8D features an intuitive interface and navigation, which many users find superior to competing products.
- External Power Supply: An external power supply is required for operation. The dedicated power supply is suitable for various uses, including field charging for RC models.
- Voice Messages: Some users have noted that the quality of voice messages can be crackling. You can adjust the volume or turn off voice messages in the system settings if this is an issue.
- Information Window Text: Be aware that the text on the information window can be small.
- Cables: Depending on the package, some required charging cables may need to be purchased separately.
11. Troubleshooting
- Battery Identification Errors: If a battery is severely over-discharged or overcharged, the charger's automatic cell count detection might be inaccurate. In such cases, manually set the correct number of strings in the charging settings.
- Charging Issues: Incorrectly setting the number of cells can prevent charging or lead to overcharging and damage. Always double-check your cell count settings.
- Voice Message Quality: If voice messages are crackling or unclear, navigate to the system settings to adjust the sound volume or disable voice prompts entirely.
- Charger Not Powering On: Ensure the DC input voltage is within the 10.0V-49.0V range and that the XT90 connector is securely plugged in with correct polarity.
- Overheating: If the charger stops due to high temperature, ensure adequate ventilation around the cooling fans. Check the 'Safe Inter temp.' and 'Safe Exter temp.' settings in Charging Safety Settings.
12. Frequently Asked Questions (FAQ)
- Q: What is the discharge current of the M8D charger?
- A: The M8D offers two discharge modes: Recycle discharge power is 0.1-30.0A @800W*2, and Normal discharge power is 0.1-10A @40W*2.
- Q: Can I charge two different types of batteries simultaneously?
- A: Yes, the M8D is a dual-channel charger, allowing you to charge two different batteries with independent settings on each channel.
- Q: Is an AC adapter included with the charger?
- A: The M8D is a DC input charger. An external DC power supply is required and typically sold separately. Please check your specific product package contents.
13. Warranty and Support
For warranty information, technical support, or service inquiries, please visit the official ToolkitRC website at www.toolkitrc.com or contact your local distributor. Keep your proof of purchase for warranty claims.
A detailed user manual (PDF) is available for download from the manufacturer's website: M8D Manual V1.0 (PDF).
© 2024 ToolkitRC Technology (Shenzhen) Co., Ltd. All rights reserved.