Yovanxer TJ7500

Contents

Yovanxer TJ7500 Remote Control Electric Screen Controller User Manual

1. Product Overview

This manual provides detailed instructions for the installation, operation, and maintenance of your Yovanxer TJ7500 Remote Control Electric Screen Controller. This device is designed to control electric projection screens, curtains, shades, and other motorized devices with ease and reliability.

Key features include:

  • Imported chip with advanced technology, reasonable design, and beautiful appearance.
  • Built-in overpressure protection and lightning protection for safe and reliable operation.
  • Long-distance radiofrequency emission design, ensuring unobstructed and simple remote control operation.
  • Intelligent learning type receiver, allowing easy setup of multiple remote control handles.
Yovanxer TJ7500 Remote Control Electric Screen Controller with remote and receiver unit.
Figure 1: Yovanxer TJ7500 Remote Control Electric Screen Controller with remote and receiver unit.

2. Specifications

Attribute Value
Model Number TJ7500
Rated Voltage AC85-265V
Load Power ≤500W
Operating Frequency 315 MHz, 433 MHz (Optional)
Control Current 3A
Control Distance 50-100m (open space)
Transmitter Batteries 23A / 12V (not included)
Motor Line Length 1.4 meters
Wireless Communication RF
Use Projectors (for screen control)

3. Package Contents

The package typically includes:

  • 1 x TJ7500 Receiver Unit
  • 1 x Remote Control (battery 23A/12V not included)
  • (Optional, depending on purchased variant) 1 x USB Trigger
Yovanxer TJ7500 Remote Control Electric Screen Controller, showing the remote, receiver unit, and USB trigger.
Figure 2: Typical package contents including receiver, remote, and USB trigger.

4. Safety Information

  • Do not install the receiver in hot and humid places.
  • Ensure the power is off before installation to prevent electric shock.
  • Pay attention to the connector not to be exposed and avoid short circuits.
  • This product is used for AC motor positive, stop, and reverse control. Ensure compatibility with your motor.

5. Setup

5.1. Wiring Installation

When installing, please check the voltage before turning off the power to prevent electric shock. The wiring should be installed as shown in the receiver panel diagram below. This installation should be performed by a professional.

Internal view of the TJ7500 V3.6 receiver unit showing the circuit board and wiring terminals for motor up, down, center, and 220V AC power.
Figure 3: TJ7500 V3.6 Receiver Wiring Diagram. Ensure proper connection of motor up wire, 220V AC power, motor center wire (ground optional), and motor down wire.

Important: Ensure wiring connectors are not exposed to prevent short circuits.

5.2. Remote Control Learning (Pairing)

To pair a new remote control with the receiver:

  1. Ensure the receiver is in standby state (red light on, motor not rotating).
  2. Press and hold the middle 'Stop' button on the receiver for 3 seconds. The red light will turn off.
  3. Immediately press any button on the remote control you wish to pair. The red light on the receiver will flash and then stay on, indicating successful learning. The remote control can now be used.

5.3. USB Trigger Setup (if applicable)

If your model includes a USB trigger for automatic projector screen control:

  1. Insert the USB trigger into an available USB port on your projector.
  2. On the receiver unit, long press the middle 'Stop' button until the red light turns off.
  3. Then, press the button on the USB trigger. The red light on the receiver will turn on, indicating successful pairing between the trigger and the receiver.
Video 1: Demonstration of connecting the USB trigger to a projector, pairing the remote control, and automatic screen operation based on projector power state.

6. Operating Instructions

6.1. Remote Control Operation

Use the buttons on the remote control to operate your electric screen or curtain:

  • Up Arrow: Raises the screen/curtain.
  • Square/Middle Button: Stops the screen/curtain.
  • Down Arrow: Lowers the screen/curtain.
Yovanxer TJ7500 Remote Control Electric Screen Controller, showing the remote and receiver unit.
Figure 4: Remote control and receiver unit.

6.2. Automatic Operation with Projector (with USB Trigger)

If you have successfully set up the USB trigger with your projector and receiver:

  • When the projector is turned off, the screen will automatically open (retract).
  • When the projector is turned on, the screen will automatically close (deploy).

This feature provides seamless integration for your home theater or presentation setup.

7. Maintenance

  • Battery Replacement: If the remote control distance is shortened or it stops responding, replace the remote control battery (23A / 12V).
  • General Care: Keep the device clean and dry. Avoid exposing it to extreme temperatures or humidity.
Remote control with open battery compartment, showing space for a 23A/12V battery.
Figure 5: Remote control battery compartment for 23A/12V battery.

8. Troubleshooting

  • Motor not working after installation: Reconfirm that the center line is connected correctly. If the issue persists, consult the supplier.
  • Motor running in the wrong direction: Exchange the ascending and descending wires.
  • Remote control distance shortened or unresponsive: Replace the remote control battery (23A / 12V).

8.1. Clearing Remote Control Codes

To clear all previously learned remote control codes from the receiver:

  1. Ensure the receiver is in standby state (red light on, motor not rotating).
  2. Press and hold the middle 'Stop' button on the receiver.
  3. Continue holding for approximately 5 seconds after the red light goes off. The red light will then flash and stay on. At this point, all previously learned remote controls will no longer work.

Note: After clearing, the controller will automatically enter learning mode. If no new remote control is paired within 5-10 seconds, it will exit learning mode.

9. User Tips

  • Always double-check the wiring, especially the motor's center line, during installation to ensure proper functionality.
  • If your motor operates in the reverse direction, a simple swap of the up and down wires on the receiver can correct this.
  • The USB trigger offers a convenient way to automate your screen with your projector, enhancing your viewing experience.
  • Keep a spare 23A/12V battery for the remote control to avoid interruptions.

10. Warranty and Support

Warranty Conditions: The product is covered by a three-year warranty for non-human damage or improper installation. This warranty covers defects in materials and workmanship under normal use.

Support: For technical assistance or inquiries, please contact:

  • Service Hotline: 008618621934178
  • Email: sales@dqprojection.com

A detailed user manual (PDF) is available for download from the seller's product page for further reference.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.