WESA YKL-HEI-01-H

Contents

WESA YKL-HEI-01-H Wall Rocker Switch Instruction Manual

Model: YKL-HEI-01-H

1. Product Overview

The WESA YKL-HEI-01-H is a European standard 1 Gang 1 Way Wall Rocker Switch designed for controlling lighting circuits. It features a flame-retardant plastic construction with an acrylic panel, suitable for various home decoration styles.

WESA 1 Gang 1 Way Wall Rocker Switch

Figure 1: WESA YKL-HEI-01-H Wall Rocker Switch

Video 1: Product overview and 360-degree view of the WESA Wall Rocker Switch.

2. Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.
  • Ensure the main power supply is turned off before any installation or maintenance.

3. Setup and Installation

Installation should only be performed by a qualified electrician or a competent person, following local electrical codes and regulations.

  1. Crucial Step: Before beginning any installation, turn off the main power switch at your circuit breaker to ensure the circuit is in a power-off state. Verify with a voltage tester.
  2. Carefully remove the existing switch (if any) and identify the wires.
  3. Refer to the wiring diagram below for correct connections.
  4. Connect the wires to the new WESA switch:
    • N is the Neutral wire (zero wire).
    • L is the Live wire.
    • E is the Ground wire (if applicable to your installation).
    • For a 1 Gang 1 Way switch, typically you will connect the incoming live wire to the 'L' terminal and the outgoing live wire to the 'L1' terminal (or similar marked output terminal for the load).
  5. Secure the switch into the wall box.
  6. Attach the faceplate.
  7. Restore power at the circuit breaker and test the switch functionality.
Wiring Diagram for 1 Gang 1 Way Switch

Figure 2: Wiring Diagram. Connect Live (L) and Neutral (N) as shown. L1, L2, L3 are outputs to lights.

Dimensions

The switch is designed to fit standard EU wall boxes. Specific dimensions for the 1 Gang 1 Way Switch are:

  • Overall Panel Size: 83mm (3.26in) x 83mm (3.26in)
  • Mounting Depth: Approximately 40mm (1.57in)
Dimensions for various switch and socket types

Figure 3: Dimensional drawing for various WESA switch and socket configurations. Refer to "1 Gang 1 Way Switch" for this model.

4. Operating Instructions

This is a simple 1 Gang 1 Way rocker switch. Press the rocker panel to toggle the connected light or appliance ON or OFF.

5. Maintenance

  • The switch features an easy-to-clean surface and a matte finish that resists fingerprints.
  • To clean, gently wipe the surface with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Ensure the switch is not exposed to water or excessive moisture.
  • For long-term storage, turn off the device and store it in a dry place, away from children.
Product features: High temperature flame retardant, Anti static, Easy to clean, Matte without fingerprints

Figure 4: Key material properties including easy cleaning and anti-static features.

6. Troubleshooting

If the switch is not functioning correctly:

  • Ensure the main power supply to the circuit is ON.
  • Check the light bulb or appliance connected to the switch to ensure it is working.
  • If the issue persists, turn off the main power supply and carefully re-check the wiring connections as per the diagram in Section 3.
  • If you are unsure, consult a qualified electrician. Do not attempt repairs if you are not competent to do so.

7. Specifications

AttributeValue
Brand NameWESA
Model NumberYKL-HEI-01-H
Item TypeSWITCHES
Switch TypePush Button Switch
MaterialPlastic (Flame Retardant)
Current Rating16A
Voltage Rating250V AC (Complies with EU LVD for mains voltage products)
FeaturesEmbedded, High Temperature Flame Retardant (up to 850°C), Anti-static, Easy to Clean
CertificationsRoHS, LVD, CE
Warranty10 years
OriginMainland China
Package Dimensions (L x W x H)9 cm x 9 cm x 5 cm
Package Weight0.119 kg
High temperature flame retardant material up to 850 degrees Celsius

Figure 5: High temperature flame retardant material for enhanced safety.

8. User Tips

  • Always prioritize safety: Double-check that power is off before touching any wires.
  • Ensure all wire connections are secure to prevent loose connections and potential hazards.
  • For a clean aesthetic, wipe the switch panel regularly with a soft, dry cloth.

9. Warranty and Support

The WESA YKL-HEI-01-H Wall Rocker Switch comes with a 10-year warranty from the date of purchase, covering manufacturing defects.

Manufacturer Information

Wenzhou Junyuan Technology Co., Ltd
Address: No. 1, Yantai Village, Shacheng Street, Wenzhou Economic and Technological Development Zone, Zhejiang Province
Email: 714637372@qq.com
Phone: +86 13587405319

EU Authorized Representative

MJCM SARL
Address: 78 Avenue des Champs-Elysees, Bureau 326
Email: mjcm190928@gmail.com
Tel: +33 767213611 or +33 780753377

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.