Teschev IEC62196 EVSE kit

Contents

Teschev Portable EV Charging Cable User Manual

Model: IEC62196 EVSE kit

1. Introduction

This manual provides instructions for the safe and efficient use of your Teschev Portable Electric Vehicle (EV) Charging Cable. This product is a circuit board integrated into a 'control box on cable' for electric vehicle AC charging, operating in mode 2 with connection mode B. The internal model is TS-QB05.

Important Note: This is a Type 2 charging cable and is NOT designed to be used as an extension cable. It is intended solely for connecting charging stations to electric vehicles.

2. Safety Precautions

  • Always ensure personal safety and take precautions to prevent electric shock.
  • Use only a power cord that meets national and local electrical standards.
  • Do not attempt to modify or disassemble the charging cable or control box.
  • Keep the charging cable and connectors clean and dry. Avoid contact with water or other liquids.
  • Ensure the charging cable is not damaged before use. Do not use if the cable or connectors show signs of wear or damage.
  • This product is not an extension cable. Connect directly between the charging station and the vehicle.

3. Product Overview

The Teschev Portable EV Charging Cable features a Type 2 connector for both the vehicle and the charging station. It includes an integrated control box for managing the charging process and ensuring safety.

Type 2 EV Charging Cable with power ratings

Figure 1: Type 2 EV Charging Cable showing female and male plugs with various power ratings (16A 1P 3.5kW, 16A 3P 11kW, 32A 1P 7kW).

Female and Male Plug Pin Configurations

Figure 2: Detailed view of the female and male plug pin configurations.

4. Setup and Connection

  1. Ensure the vehicle and charging station are turned off before connecting.
  2. Insert the male plug of the charging cable into the charging station.
  3. Insert the female plug of the charging cable into your electric vehicle's charging port.
  4. Ensure both connections are secure.
  5. The control box will perform a self-test (indicated by a constant flashing light). After the self-test, it will enter standby mode (no gun inserted).
EV Charging Cable Connection Diagram

Figure 3: Diagram illustrating the connection of the female plug to the car and the male plug to the charging station.

Charging Connection Process and Environmental Ratings

Figure 4: Connection diagram from charging station to EV, highlighting operating temperature, IP65 rating, and certifications.

5. Operating Instructions

5.1 Current Setting Steps

  1. Insert the control box plug into a national standard-compliant socket.
  2. The control box will perform a self-test and enter standby mode (no gun inserted).
  3. In standby state, press and hold the touch area on the control box for 2 seconds to enter current setting mode. The corresponding current indicator will flash.
  4. Click the touch area to cycle through and select the desired current (e.g., 8A, 10A, 13A, 16A). The selected current indicator will flash.
  5. After selecting the desired current, press and hold the touch area for 2 seconds to confirm the setting. The control board will save the new current value, initialize, and begin operation with this setting.
  6. Once the current is set, plug the cable into the vehicle to begin charging.
AC Charging Cable Standard and Protection

Figure 5: AC Charging Cable meeting IEC 2010 SHEET 2-lle Standard, with IP65 protection.

Product Properties: Overheating and Leakage Protection

Figure 6: Product properties highlighting overheating and leakage protection, ergonomic design, and mechanical life.

5.2 Charging Reservation Process

This feature allows you to reserve charging for off-peak hours to save money and effort. Charging can be reserved for 1 to 10 hours.

  1. Power on the charger first (do not plug it into the vehicle yet).
  2. Long press the touch area for 3 seconds to enter the secondary menu.
  3. Select the charging reservation time.
  4. Long press the touch area for 3 seconds to enter the charging reservation setting.
  5. Press the button "charge after 1 hour" once, then long press for 3 seconds to lock the setting.
  6. Plug the cable into the vehicle and wait for the countdown to initiate automatic charging.

Note: This reservation function may also be achieved through the built-in reservation function in your electric vehicle.

Control Box Display Analysis

Figure 7: Control box display showing real-time temperature, voltage, charging current, power, and charging time.

6. Maintenance

The Teschev EV charging cable is designed for durability and low maintenance. The terminal pins are made of pure copper alloy with silver plating, which prevents dust accumulation and sparks, ensuring a long service life of over 50,000 insertions and removals without deformation.

  • Regularly inspect the cable and connectors for any signs of physical damage, cuts, or fraying.
  • Keep the connectors clean and free from dirt, dust, and moisture. Use a dry, clean cloth to wipe them if necessary.
  • Store the cable in a dry place, away from direct sunlight and extreme temperatures, when not in use.
  • Do not drive over the cable or subject it to excessive tension or bending.

7. Troubleshooting: Indicator Definitions and Action Scheme

The control box features indicator lights (Green, Blue, Red) to communicate its status and any potential fault conditions. The flashing frequency during protection is 0.5 seconds on and 0.5 seconds off, with a 2-second interval after the specified number of flashes.

Fault Code Green Blue Red Meaning
Standby On Off Off Ready for connection
Connecting Flash Off Off Cable connected, awaiting charging start
Charging On Flash Off Charging in progress
End of charging Off On Off Charging complete
Overtemperature (E1) Off Off Flashes once Internal temperature too high
Undervoltage (E2) Off Off Flashes twice Input voltage too low
Overvoltage (E3) Off Off Flashes three times Input voltage too high
Grounding (E4) Off Off Flashes four times Grounding fault detected
Temporary overcurrent (E5) Off Off Flashes five times Temporary current overload
Permanent Overcurrent (E6) Off Off Flashes six times Sustained current overload
Leakage (E7) Off Off Flashes seven times Electricity leakage detected
Relay adhesion (E8) Off Off Flashes eight times Internal relay fault
CP Anomaly (E9) Off Off Flashes nine times Control Pilot signal anomaly
Emergency stop (E10) Off Off Flashes ten times Emergency stop activated
Small current stop (E11) Off Off Flashes eleven times Insufficient current detected
Plug overtemperature (E12) Off Off Flashes twelve times Plug connector overtemperature

8. Specifications

8.1 General Parameters

Feature Specification
Brand Name Teschev
Model Number IEC62196
Charger Type EV Charging Cable
Cable Length 3 Meters
Weight 3.8 kg
Origin Mainland China

8.2 Electrical Parameters

Feature Specification
Rated AC Operating Voltage 80-260V AC
Rated Voltage 380-450V
Rated Current 16A / 32A (MAX)
Phase Number 1 Phase / 3 Phases
Operating Frequency 50-60Hz
Power (W) 3.6KW / 7.2KW / 11KW
Residual Current Rated Operating Current M22mA
Duty Ratio 26.67%@1KHZ

8.3 Environmental and Material Specifications

Feature Specification
Working Temperature -30°C ~ +50°C
Operating Humidity Range 3-95% RH
Storage Temperature Range -50°C ~ +85°C
Elevation Less than 2000 m
IP Grade (Protection) IP65
Flame Retardant Rating UL94V-0
Insulation Material Thermoplastic
Contact Material Copper Alloy, Silver Plated
Case Material Copper, Thermoplastic material
Mechanical Life On-load plug in/pull out > 10,000 times

8.4 Protection Box Functions

  • Overvoltage protection
  • Undervoltage protection
  • Overcurrent protection
  • Electricity leakage protection
  • Grounding protection: Continuous monitoring of grounding protection
  • Protection in case the ground line is not connected
  • Lightning protection
  • Over-temperature protection
  • Power regulation: 8A, 10A, 13A, 16A (touch adjustment)

9. User Tips

  • Always set the desired charging current *before* plugging the cable into your vehicle.
  • Utilize the charging reservation feature to schedule charging during off-peak electricity hours to potentially save on energy costs.
  • Ensure the charging cable is fully inserted into both the charging station and the vehicle to prevent loose connections and potential faults.
  • If a fault indicator appears, refer to the Troubleshooting section (Section 7) to identify and resolve the issue.
  • Remember, this cable is designed for direct connection and should not be used as an extension cord.

10. Warranty and Support

For detailed warranty information, please refer to the official product documentation provided by Teschev. A user manual in PDF format is available for download and can be accessed via the following link: User Manual (PDF).

For technical support or service inquiries, please contact your retailer or the manufacturer directly.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.