SARIK Wireless 433MHz Remote Control Light Switch with 10A Relay Receiver

Contents

Wireless 433MHz Remote Control Light Switch

User Manual

1. Introduction

Thank you for purchasing the SARIK Wireless 433MHz Remote Control Light Switch with 10A Relay Receiver. This device allows you to wirelessly control your lights or other electrical appliances, providing convenience and flexibility. This manual provides essential information for the safe installation, operation, and maintenance of your new device.

2. Safety Precautions

  • Electrical Safety: Always disconnect power at the circuit breaker before performing any electrical work or installation. Do not operate the device in electricity; ensure power is off before wiring and only restore power after testing.
  • Installation: Installation should be performed by a qualified electrician or in accordance with local electrical codes.
  • Environment: Avoid using the product in environments with strong electromagnetic interference, large electronic equipment, or metal obstructions, as these can reduce remote control range and affect performance.
  • Abnormal Use: Do not use this electronic product abnormally. Abnormal use can reduce product performance, longevity, and may cause serious damage.
  • Battery: Ensure batteries are replaced in a timely manner when the remote control distance decreases, indicating low voltage.

3. Package Contents

Please check the package for the following items:

  • 1 x 433MHz Relay Receiver (Controller)
  • 1 x Wireless Wall Panel Switch (Remote Control)
  • 2 x CR2016 Batteries (pre-installed in remote control)
SARIK Wireless 433MHz Remote Control Light Switch Receiver and Remote
Figure 1: Receiver and Remote Control included in the package.

4. Specifications

4.1. Wireless Wall Panel Switch (Remote Control)

Operating Frequency433MHz
Power Source2 x 3V CR2016 Batteries (included)
MaterialPVC
Buttons2
DimensionsApprox. 60mm x 30mm (or 5.0cm diameter x 1.5cm thickness)
Operating Voltage3V
Operating Current12mA
Transmitting Power10mW
Modulation ModeASK (AM)
Encoding TypeLearning Code (EV1527)
Transmission Distance20~50m (indoor), >50m (open space)
Remote Control Dimensions
Figure 2: Dimensions of the Wireless Wall Panel Switch.

4.2. 433MHz Relay Receiver (Controller)

Input PowerAC85-240V 60HZ/50HZ
Max Current10A
RF Frequency433MHz
Working Temperature-30°C ~ +80°C
RF Working ModeSuperheterodyne
Receive Sensitivity>97dBm
Load Power<1100W
Remote Storage10pcs
Support Remote TypeLearning Code 1527code
Dimensions47.4mm x 42mm x 22.8mm

4.3. General

Wireless CommunicationRF 433MHz
UseSwitch
OriginMainland China
CertificationCE
Key Features of the Wireless Switch System
Figure 3: Key features including 50m distance, easy use, low power, strong signal, 433 module, good quality, through-wall capability, and portability.

5. Setup and Installation

5.1. Receiver Wiring Diagram

WARNING: Ensure power is disconnected at the circuit breaker before proceeding with wiring.

  1. Connect the Live wire (L) from your power source to the 'L' terminal on the receiver's INPUT side.
  2. Connect the Neutral wire (N) from your power source to the 'N' terminal on the receiver's INPUT side.
  3. Connect the Live wire (L) of your light fixture or appliance to the 'L' terminal on the receiver's OUTPUT side.
  4. Connect the Neutral wire (N) of your light fixture or appliance to the 'N' terminal on the receiver's OUTPUT side.
  5. Securely fasten all wires to their respective terminals.
  6. After wiring, you can use screws or adhesive tape to fix the receiver in an appropriate position (e.g., inside a switch box or junction box).
Receiver Wiring Diagram
Figure 4: Wiring diagram for connecting the receiver to a light fixture. Ensure Live (L) and Neutral (N) connections are correct for both input and output.
Receiver Wiring Diagram with RF433MHz
Figure 5: Detailed view of the receiver terminals and RF433MHz indication.

6. Operation

6.1. Pairing the Remote Control with the Receiver

After wiring the receiver and restoring power, you need to pair the remote control with the receiver:

  1. Step 1: Press the learning button on the receiver twice. The LED indicator on the receiver will flash twice and then turn on continuously.
  2. Step 2: Within 3 seconds, press any button on your desired remote control. The LED indicator on the receiver will flash, indicating successful pairing.
Pairing Process with Learning Button
Figure 6: Illustrates pressing the learning button on the receiver and then a button on the remote control for pairing.

6.2. Clearing Paired Remote Controls

To clear all paired remote controls from the receiver's memory:

  • Press the learning button on the receiver 8 times. The LED indicator will flash continuously, signifying that all previously matched remote controls are now invalid.

6.3. Using the Remote Control

Once paired, simply press the configured button on the remote control to toggle the connected light or appliance ON/OFF.

Remote Control in Use
Figure 7: Example of using the remote control to operate a lamp.
Application Environments
Figure 8: The wireless switch system can be used in various environments such as dining rooms, hallways, offices, and garages.

7. Maintenance

7.1. Battery Replacement

The remote control is powered by two CR2016 batteries. If you notice a decrease in the remote control's range or responsiveness, it's time to replace the batteries.

  1. Carefully open the remote control casing.
  2. Remove the old CR2016 batteries.
  3. Insert new CR2016 batteries, ensuring correct polarity.
  4. Close the remote control casing securely.
Remote Control with Battery Included
Figure 9: The remote control comes with batteries included.

7.2. Cleaning

Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents, as they may damage the surface or internal components.

8. Troubleshooting

ProblemPossible CauseSolution
Remote control range is short or inconsistent.
  • Low battery in remote control.
  • Strong interference sources (metal objects, large electronics, electromagnetic fields).
  • Too many obstacles between remote and receiver.
  • Replace remote control batteries.
  • Relocate receiver or remote to avoid interference.
  • Ensure clear line of sight or fewer obstructions.
Light/appliance does not respond to remote.
  • Remote not paired with receiver.
  • Power supply to receiver is off.
  • Wiring error.
  • Perform pairing procedure (Section 6.1).
  • Check power supply to the circuit.
  • Verify wiring connections (Section 5.1) with power off.
Receiver LED does not light up.
  • No power to the receiver.
  • Faulty receiver.
  • Check power supply and wiring.
  • Contact support if power is confirmed and LED remains off.

9. User Tips

No specific user tips were available from customer reviews or Q&A for this product at this time. Always ensure proper wiring and test functionality before final installation.

10. Warranty and Support

For warranty information or technical support, please refer to your purchase documentation or contact the seller directly. Keep your proof of purchase for any warranty claims.

A detailed user manual in PDF format is available for download: Download User Manual (PDF)

© 2023 SARIK. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.