1. Introduction
Thank you for choosing the XMSJ Cordless Electric Drill. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your new tool. Please read this manual thoroughly before first use and keep it for future reference.

Figure 1: XMSJ Cordless Electric Drill models (12V, 16.8V, 21V)
2. Safety Instructions
Always follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury.
- Wear appropriate personal protective equipment (PPE) such as safety glasses, gloves, and hearing protection.
- Keep your work area clean and well-lit.
- Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
- Keep children and bystanders away while operating a power tool.
- Ensure the battery is fully charged before use and always use the charger provided.
- Do not force the power tool. Use the correct power tool for your application.
- Disconnect the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools.
3. Product Overview
Familiarize yourself with the components of your cordless electric drill.

Figure 2: Key components of the Cordless Electric Drill
- 1. Self-locking Chuck (0.8-10mm / 3/8" max): For securing drill bits and screwdriver bits.
- 2. Torque Setting (25+1 Positions): Adjusts the amount of torque for different applications.
- 3. LED Light: Illuminates the work area.
- 4. Variable Speed Switch: Controls the drilling/driving speed.
- 5. Forward/Reverse Button: Changes the rotation direction of the chuck.
- 6. Li-ion Battery: Provides power to the drill.
- 7. Mode Selector (0-350rpm / 0-1400rpm): Selects between low and high-speed ranges.
4. Setup
4.1 Unpacking
Carefully remove all contents from the packaging. Ensure all items listed below are present:
- Cordless Electric Drill
- Li-ion Battery (one or two, depending on kit)
- Charger Adapter
- Accessory Kit (if included, e.g., drill bits, screwdriver bits)
- User Manual (this document)

Figure 3: Example of drill kits and accessories
4.2 Charging the Battery
- Ensure the battery is securely attached to the charger.
- Plug the charger adapter into a standard electrical outlet (100-240V AC, 50/60Hz).
- The charging indicator light on the charger will illuminate (refer to charger for specific light behavior).
- A full charge typically takes 2-4 hours.
- Once fully charged, disconnect the charger from the power outlet and remove the battery.
Note: It is recommended to fully charge the battery before first use.
4.3 Attaching/Detaching the Battery
- To Attach: Align the battery pack with the base of the drill handle and slide it in until it clicks securely into place.
- To Detach: Press the battery release buttons (usually on the sides of the battery) and slide the battery pack out.
4.4 Installing/Changing Drill Bits
This drill features a self-locking keyless chuck for easy bit changes.
- Ensure the drill is off and the battery is removed for safety.
- Rotate the front part of the chuck counter-clockwise to open the jaws.
- Insert the drill bit or screwdriver bit into the chuck jaws. Ensure the bit is inserted as far as it will go for maximum grip.
- Rotate the front part of the chuck clockwise to tighten the jaws firmly around the bit. Hand-tighten only; do not use tools to tighten the chuck.
- To remove a bit, reverse the process.
5. Operating Instructions
5.1 Powering On/Off and Variable Speed
- To turn the drill on, press the variable speed switch. The speed increases as you press the switch further.
- To turn the drill off, release the variable speed switch.
5.2 Forward/Reverse Rotation
- The forward/reverse button is located above the variable speed switch.
- Push the button to the left for forward (clockwise) rotation (for drilling and tightening screws).
- Push the button to the right for reverse (counter-clockwise) rotation (for removing screws or freeing a stuck drill bit).
- When the button is in the center position, the trigger is locked, preventing accidental starting.
5.3 Torque Setting
The torque adjustment ring allows you to select the desired torque for your application. There are 25 torque settings plus a drill mode (indicated by a drill icon).
- Lower numbers (1-5): For driving small screws or working with soft materials.
- Medium numbers (6-15): For driving medium screws or working with medium-density materials.
- Higher numbers (16-25): For driving larger screws or working with harder materials.
- Drill icon: For drilling applications, providing maximum torque.
Always start with a lower torque setting and increase it as needed to prevent over-tightening or damaging the workpiece.
5.4 Mode Selector (2-Speed Adjustment)
The mode selector switch, located on top of the drill, allows you to choose between two speed ranges:
- Position 1 (Low Speed, 0-350rpm): Ideal for driving screws, applications requiring high torque, or drilling larger holes in softer materials.
- Position 2 (High Speed, 0-1400rpm): Ideal for drilling smaller holes, faster drilling, or applications requiring less torque.
Always ensure the drill has come to a complete stop before changing the speed setting.
5.5 LED Work Light
The integrated LED light automatically illuminates when the variable speed switch is pressed, providing visibility in dimly lit work areas.
5.6 General Operation Tips

Figure 4: Using the drill for woodworking
- Always hold the drill firmly with both hands if possible, especially when drilling larger holes or in tough materials.
- Apply steady, even pressure. Do not force the drill.
- For drilling, start with a slow speed to create a pilot hole, then increase speed as needed.
- For driving screws, match the bit type to the screw head and use an appropriate torque setting.
6. Maintenance
6.1 Cleaning
- Always remove the battery pack before cleaning.
- Use a clean, damp cloth to wipe down the exterior of the tool. Do not use harsh chemicals or abrasive cleaners.
- Keep the ventilation openings clear of dust and debris to prevent overheating. Use compressed air if necessary.
6.2 Battery Care
- Store batteries in a cool, dry place away from direct sunlight and extreme temperatures.
- Do not store batteries in a discharged state for extended periods. Recharge them periodically if not in use.
- Do not expose batteries to water or moisture.
6.3 Storage
- Store the drill and its accessories in a clean, dry, and secure location, out of reach of children.
- If storing for an extended period, remove the battery from the drill.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Drill does not start | Battery not charged; Battery not properly inserted; Forward/Reverse switch in center (locked) position; Faulty battery or tool. | Charge battery; Reinsert battery securely; Move F/R switch to forward or reverse; Contact support if problem persists. |
| Battery not charging | Charger not plugged in; Faulty outlet; Damaged charger or battery. | Check charger connection; Test outlet with another device; Inspect charger/battery for damage; Contact support. |
| Poor drilling/driving performance | Low battery charge; Incorrect speed/torque setting; Dull or incorrect drill bit. | Recharge battery; Adjust speed/torque; Replace or sharpen drill bit; Use appropriate bit for material. |
| Drill overheats | Overuse; Blocked ventilation; Excessive pressure. | Allow tool to cool down; Clear ventilation slots; Reduce pressure during operation. |
8. Specifications
| Feature | Specification |
|---|---|
| Brand Name | XMSJ |
| Model Number | Electric Drill Electric Screwdriver |
| Rated Voltage | 12V / 16.8V / 21V (depending on model) |
| Power Source | Battery (Lithium-Ion) |
| Motor Type | Brushed |
| No-Load Speed | 0-350rpm / 0-1400rpm (2-speed) |
| Rated Torque | 25+1 Settings |
| Max. Drilling Diameter | 0.8-10mm (3/8" max) |
| Rated Input Power | 130W |
| Frequency | 50/60Hz |
| Chuck Type | Keyless |
| Battery Included | Yes |
| Charging Time | 2-4 Hours |
| Charger Adapter Input | 100-240V AC 50/60Hz |
| Charger Adapter Output | 12.6V DC 500mAh |
| Special Features | Light Weight, LED Worklight |
| Application | Household, screwing, drilling for decoration |
| Weight (21V Kit) | 1.99kg |
| Dimensions (21V Kit) | 305 x 240 x 77mm |
| Weight (12V Kit) | 1.04kg |
| Dimensions (12V Kit) | 285 x 245 x 75mm |

Figure 5: 21V Kit dimensions and weight

Figure 6: 12V Kit dimensions and weight
9. User Tips
- Always select the correct drill bit or screwdriver bit for the task and material to ensure efficiency and prevent damage.
- For optimal performance, ensure the battery is fully charged before starting any significant work.
- When drilling into hard materials, use a slower speed and apply steady pressure. Consider using a pilot hole for precision.
- Regularly check and clear the drill's ventilation slots to prevent dust buildup and ensure proper cooling.
10. Warranty and Support
For any questions, technical assistance, or warranty claims, please contact the seller directly through your purchase platform. Please have your order details ready when contacting support.
A more detailed user manual may be available in PDF format: View PDF User Manual