Sunster 8KW Diesel Air Heater

Contents

Sunster 8KW Diesel Air Heater User Manual

Model: 8KW Diesel Air Heater

1. Introduction

This manual provides detailed instructions for the safe and efficient operation, installation, and maintenance of your Sunster 8KW Diesel Air Heater. Please read this manual thoroughly before use and keep it for future reference.

1.1 Function

The Sunster Diesel Air Heater is designed to prevent damage to vehicles caused by sudden temperature drops, improve interior temperature, and preheat engine coolant to avoid low-temperature wear. It is conducive to thawing vehicle interiors, assisting with car starts, and defrosting car glass.

2. Safety Warnings

  • Ensure proper ventilation when operating the heater to prevent carbon monoxide buildup.
  • Do not place flammable materials near the exhaust pipe.
  • The exhaust pipe must be straight and not angled upwards to ensure smooth exhaust.
  • Exhaust from the exhaust pipe must be discharged outdoors.
  • Ensure the power supply is 12V 15A or higher for 12V systems, or 24V 15A or higher for 24V systems.
  • Do not bend the exhaust pipe too much as it can affect exhaust.
  • Always check for firm installation and placement of the machine.

3. Package Contents

Upon unpacking, please verify that all items listed below are present and undamaged:

Diagram showing all included parts for the Sunster Diesel Air Heater, including the main unit, remote control, air filter, fixed plate, air outlet pipe, intake pipe, exhaust pipe, manual, battery power cord, fixture accessories set, AC-DC adapter power, and silencer.
Figure 1: Included Accessories and Dimensions
  • Main Heater Unit
  • Remote Control
  • Air Filter
  • Fixed Plate
  • Air Outlet Pipe (Stretchable)
  • Intake Pipe
  • Exhaust Pipe
  • User Manual (PDF available online: Sunster Diesel Heater User Manual PDF)
  • Battery Power Cord
  • Fixture Accessories Set
  • AC-DC Adapter Power
  • Silencer

4. Specifications

AttributeValue
Brand NameSunster
Item TypeHeating & Fans
MaterialAluminum + Plastic
CertificationRoHS, FCC, CE
Fuel TypeDiesel only
Heater Power8KW
VoltageDC 12V & 24V; AC 110-240V
Power Adapter InputAC110-240V 50-60Hz
Adjustable Temp. Range46.4°F - 96.8°F (8°C - 36°C)
Heater Working Temperature-40°C ~ +20°C / -40°F ~ +68°F
Oil Pump Working Temperature-40°C ~ +20°C / -40°F ~ +68°F
Air Outlet pipe diameter76mm (Stretchable air pipe)
Intake pipe diameter25mm
Exhaust pipe diameter25mm
Control MethodLCD + Remote Control
Noise<75DB
Startup Current13A
Rated Current3A
Tank Capacity5L / 1.3gal
Fuel Consumption0.18-0.45 (L/H)
Item Weight8.9kg
Item Height39cm
Item Width17.7cm
Item Length40cm
Dimensions of the Sunster Diesel Air Heater: 420mm (16.54in) length, 410mm (16.14in) height, 155mm (6.1in) width.
Figure 2: Product Dimensions

5. Installation

This section provides general installation guidelines. For a visual guide, please refer to the installation video below.

Video 1: Vertical All-in-One Installation Guide. This video demonstrates the unpacking, measuring, drilling, and pipe installation steps for the heater.

5.1 General Installation Steps

  1. **Unpacking**: Carefully remove all components from the packaging.
  2. **Measure Hole Spacing**: Use a measuring tape to determine the required hole spacing for mounting.
  3. **Drill Holes**: Use a 30mm tool to punch holes for the exhaust and intake pipes.
  4. **Install Exhaust Pipe**: Attach the exhaust pipe to the front of the unit using clips. Ensure the exhaust pipe is straight and not angled upwards to allow for smooth exhaust. The exhaust must be discharged outdoors.
  5. **Install Intake Pipe**: Attach the intake pipe to the back of the unit using clips.
  6. **Secure Machine**: Check that the machine is firmly installed and placed. Mark the location for mounting screws, drill pilot holes, and secure the unit.
  7. **Install Air Filter**: Install the air filter element onto the intake pipe. The clamp can be fixed in any position.
  8. **Install Silencer**: Attach the silencer to the exhaust pipe. Ensure no flammable materials are near the exhaust pipe. The exhaust pipe should not be bent too much to affect the exhaust.
  9. **Install Outlet Duct**: Attach the outlet duct to the air outlet.
  10. **Connect Power**: Connect the battery power cord. When installing the power supply, ensure that the power supply is 12V 15A or higher (for 12V models) or 24V 15A or higher (for 24V models).
  11. **Add Diesel**: Add diesel fuel to the tank.
  12. **Initial Startup**: Turn on the unit and wait for it to prime and start heating.
  13. **Ventilation**: Pay attention to ventilation when turning on the machine, especially in enclosed spaces.
Diagram showing the internal structure of the diesel air heater, including air inlet, air fan, flame retardant impeller, combustion chamber, ignition plug, heating zone, air outlet, and smart motherboard (12V 24V Auto-switching). It also highlights energy-saving fuel pump, aluminum body design, and 100% conservation.
Figure 3: Internal Structure Diagram

6. Operation

6.1 Control Panel and Remote Control

Image showing the intelligent LCD panel and remote control for the Sunster Diesel Air Heater. Features include 24-hour timing function, temperature/gear regulation, and language switching (German, English, Russian).
Figure 4: Intelligent LCD Panel & Remote Control

6.1.1 S-A2013SL Model

Working Mode:

  1. **Gear Mode**: Gear setting adjustable from 1 to 10.
  2. **Temperature Control Mode**: Temperature adjustable from 8°C to 36°C. The control switch's gear position can be adjusted at any time. Adjusting the operating gear quickly reaches the set temperature, making the heater run more intelligently and economically.
  3. **Display**: When powered off, the screen shows current time. When powered on, it shows running time.
  4. **Fault Code**: If a fault occurs, a fault code will flash on the display for easier troubleshooting.

Instructions:

  • **Power On/Off**: Press the [Power button] for 1 second to turn on/off.
  • **Mode Switch**: In gear mode, press [Set button] to switch to temperature control mode. In temperature control mode, press [Set button] to switch to gear mode.
  • **Gear Adjustment**: Press [Up Adjustment button] for +1 (max 10 gears/36°C), press [Down Adjustment button] for -1 (min 1 gear/8°C).

6.1.2 S-A2018 Model

Button Description:

SymbolDefinitionDescription
⏻On/Off key1. Long press 1 second to start, screen displays ON. 2. Press and hold for 1 second to turn off the device, and the screen will display OFF.
OKConfirm key1. Short press to check the machine status. 2. In the setting state, confirm the current setting value and enter the next parameter setting.
⚙Setting Key1. Enter parameter setting mode.
▲Up key1. In daily use (not in set state), increase the working temperature or oil volume. 2. In the setting state, adjust the setting parameters upward.
▼Down key1. In daily use (not in set state), lower the operating temperature or oil volume. 2. In the setting state, adjust the setting parameters downward.

6.2 Basic Operation Instructions

FunctionOperationDisplayOperation Notes
Query Machine stateShort press OK button1. Running time (24-hour system)
2. Ambient temperature
3. Work Temperature/Pump oil level
4. Supply voltage
Each press switches a state. Cycle display.
Manual/Automatic Mode SwitchingShort press OK key and Up Adjust key at the same time1. Manual temperature control mode (P-Number HZ Representative Pump oil volume)
2. Automatic temperature control mode (25°C digital represents temperature Spend)
1. In automatic mode, oil volume adjusts automatically to maintain set temperature.
2. Manual mode pump oil volume is limited; current setting won't auto increase/decrease oil volume and wind speed; clear gears.
Temperature measurement Unit SwitchingShort press up and down keys at the same time1. Celsius display digital °C
2. Fahrenheit display number °F
Select temperature measurement unit according to usage habits.
On/Off Manual fuel RaiseShort press Set key and Adjust key at the same time1. Open: Initial display H-oF, short press up key to display H-on
2. Off: Initial display is H-on, short press down key to display H-OF
3. Short press setting key to exit and return to main interface
1. Manual fuel filling function is disabled by default.
2. H-OF (closed state) H-on (open Enabled state).
3. When oil reaches machine's oil inlet, stop. Too much fuel causes black smoke.
Remote control pairingLong press Down key1. HF-1 display (corresponding to simple remote control)
2. Then short press the power button on the remote control at the same time, Transmit remote control signal
1. Remote control pairing function needs to be turned off when heater is turned off. Machine status.
2. If pairing is successful, device automatically exits pairing interface, enters power-on state. If pairing fails, it won't enter machine status.
3. If no remote control signal is received within time limit, device automatically exits pairing mode.

6.3 Advanced Settings

Basic settings: In the power on state, press and hold the [Setting button] for 3s to enter.

  1. **Set Current Time**: Press [Set Key] to set, use [Up/Down Adjust Key] to switch.
  2. **Set Automatic Start Time**: Same method as above.
  3. **Set Running Time after Automatic Start**: Same method as above, switching unit is 0.5 hours.
  4. **Set Automatic Start Function ON/OFF**: Screen alarm icon is always on when enabled. Modify with [Up/Down Adjust Key], confirm with [Set Key]. Hold [Set Key] for 3s to save and return.

Engineering mode: Press and hold the [Up Adjust Key] and [Down Adjust Key] for 3s in the power-on state to enter engineering mode. Use [Up Adjust Key] for item +1, [Down Adjust Key] for item -1. Display shows data items:

  • 001: Heater mainboard version number
  • 002: fault code
  • 003: Shell temperature
  • 004: power supply voltage
  • 005: Heater operating position
  • 006: Cab temperature
  • 007: altitude
  • 008: Language switching

Temperature switching: Long press the adjustment key in the power-on state to switch between Fahrenheit and Celsius.

Remote control matching: Long press the upper adjustment key in the power-on state, interface displays "P-01". Then press the remote control plus and minus key, minus key, mode switch key, power button, and return to the operation interface after successful matching.

Pumping oil mode: Long press the [Confirm/Pump Oil] key when the version number is displayed during the first power-on self-test until the screen displays a countdown of '300s'. Release the key to start pumping oil. Pumping oil automatically ends after 300s or press the [Power Button] to end pumping oil and shut down.

Setting parameters: Short press the setting button three times. Enter password Code 1688. It is not recommended for customers to modify it at will. The default optimal parameters have been set.

7. Maintenance

  • Regularly check the air filter for cleanliness and replace if necessary.
  • Inspect all pipes (exhaust, intake, air outlet) for any blockages, damage, or loose connections.
  • Ensure the fuel tank is adequately filled with clean diesel.
  • Periodically check electrical connections for tightness and signs of wear.
  • Keep the heater unit clean and free from dust and debris.

8. Troubleshooting (E-Codes)

If the heater encounters an issue, an error code (E-code) may be displayed. Refer to the table below for common fault codes and their solutions.

Fault LightFault TypeTroubleshooting
E-01Abnormal voltageCheck if heater power supply voltage type matches actual vehicle voltage. For 24V, check if supply voltage is >32V or <18V. For 12V, check if supply voltage is >18V or <9V. Check if main wiring harness connector is loose.
E-03Ignition plug abnormalityCheck if ignition plug is loosely connected. If faulty, replace it. If mainboard is faulty, replace it.
E-04Oil pump abnormalityCheck if oil pump plug is loose or wiring harness is broken. If oil pump is faulty, replace it.
E-05Overheat protectionFurnace temperature sensor is wrong model or faulty, replace sensor. If mainboard is faulty, replace it.
E-06Fan abnormalityCheck if fan impeller is stuck or fan plug is loose. If fan is faulty, replace it. Check if fan wheel induction magnet is missing or has wrong polarity. Check if mainboard wind speed sensor is normal. If mainboard is faulty, replace it.
E-08Lack of oil and flameoutCheck if fuel tank is low on fuel.
E-09Overheat protection sensorCheck if temperature sensor connector is loose. If sensor is faulty, replace mainboard. If mainboard is faulty, replace mainboard.
E-10Secondary startup failureCheck if oil pump is working. Check if interfaces of oil circuit are waxed or blocked.

9. User Tips

  • **Heating Capacity**: While advertised as 8KW, some users note the actual heating capacity might be slightly lower but still sufficient for heating spaces like garages or small utility rooms.
  • **Fuel Consumption**: At maximum setting, expect approximately 0.5 liters of diesel per hour.
  • **Ventilation**: Always ensure adequate ventilation, especially when using the heater in enclosed spaces like garages or RVs.
  • **Installation**: Pay close attention to the exhaust pipe installation to ensure it's straight and properly vented outdoors to prevent issues like black smoke.
  • **Power Supply**: Verify your power supply meets the minimum requirements (12V 15A or 24V 15A) for stable operation.
  • **Controls**: The controls are generally straightforward, but take a moment to familiarize yourself with the panel and remote programming.
  • **Timer Reset**: If disconnecting from the network, the time and programming may need to be reset.
  • **Manual**: The included manual might be basic; refer to the online PDF for more details if available.

10. Warranty and Support

Sunster is committed to providing quality products and support. All products are certified by CE, WEE, FCC, EAC, and UKCA.

For any problems or inquiries, please contact the store customer service or send an email to our after-sales team at: cs@sunster.tech.

For business-related issues, please contact: sunster@sunster.tech.

© 2024 Sunster. All rights reserved.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.