MASO Front Door Molding Trim with 6 Clip Points

Contents

User Manual: Front Door Side Molding Cover Trim

Model: Front Door Molding Trim with 6 Clip Points

1. Introduction

This manual provides essential information for the safe installation, use, and maintenance of your new Front Door Side Molding Cover Trim. Please read this manual thoroughly before installation and keep it for future reference.

This product is designed for vehicle exterior protection and decoration, specifically for the front left or right door of compatible van models.

2. Safety & Warnings

⚠ Warning:

  • Children should be kept away from small parts (clips) under adult supervision to avoid the risk of accidental swallowing.
  • Installation should ideally be carried out by professional technicians to ensure proper fitment and safety.

3. Product Specifications

Product NameFront Left/Right Door Side Molding Cover Trim
BrandMASO
Model NameFront Door Molding Trim with 6 Clip Points
MaterialABS Plastic
OEM NO.735422817, 735422811
Item TypeStyling Mouldings
Dimensions (Approx.)Length: 420mm (16.54 inches), Width: 195mm (7.68 inches)
CompatibilityCitroen JUMPER II Van, Fiat DUCATO, Opel MOVANO, Peugeot BOXER
OriginMainland China
Product dimensions: 420mm length, 195mm width

Figure 1: Product Dimensions

4. Setup & Installation Instructions

It is recommended that the installation be carried out by professional technicians.

  1. Inspect Product: Before installation, carefully inspect the molding trim for any damage.
  2. Verify Fitment: Ensure the product dimensions and shape match the intended installation location on your vehicle's front door (left or right).
  3. Prepare Surface: Clean the installation surface thoroughly. It must be free of dust, oil, grease, wax, and moisture. Use a suitable automotive cleaner and allow the surface to dry completely.
  4. Positioning: Carefully align the molding trim to its intended position on the door. This step is to ensure correct placement before securing.
  5. Apply Trim: Align the product precisely in position. Ensure all 6 clips are properly seated into the corresponding holes on the vehicle. Apply even, firm pressure across the entire surface to ensure proper engagement.
  6. Secure Clips: Ensure each of the 6 clips snaps securely into place.
Front door side molding cover trim installed on a van, showing the location

Figure 2: Installation Location Example

Rear view of the molding trim showing the 6 attachment clips

Figure 3: Rear View with Clips

5. Maintenance

  • Post-Installation Care: After installation, it is recommended to allow the product to set for a period of time (e.g., 24-48 hours) before washing the vehicle or exposing it to excessive moisture.
  • Regular Inspection: Regularly check the security of the molding trim. If any loosening is observed, address it promptly to prevent detachment or damage.
  • Cleaning: Clean the molding trim with standard automotive cleaning products. Avoid abrasive cleaners or harsh chemicals that could damage the plastic finish.

6. Troubleshooting

  • Trim Not Secure/Loose: Ensure the installation surface was thoroughly cleaned and dry before application. For clip-on versions, ensure all clips are fully engaged. If issues persist, professional re-installation may be required.
  • Misalignment: If the trim appears misaligned after installation, it may need to be carefully removed and re-positioned. This is easier if done shortly after initial installation.

7. User Tips

  • Verify Part Location: Always double-check that you are ordering the correct molding for the specific location on your vehicle (e.g., front door, rear door, side panel). This product is specifically for the front left or right door.
  • Pre-Fitment is Key: Before snapping in clips, always dry-fit the trim to ensure it matches the contour and size of the intended area.

8. Manufacturer & Support

Manufacturer Information:

Guangzhou Kuxiong Shi Trading Co., Ltd
No. 503, Building 3, Courtyard 2, Zhongquantang Road, Industrial Avenue, Haizhu District, Guangzhou City
Phone: +86-18814180059
Email: tingting26181@outlook.com

EU Authorized Representative:

Sea&Mew Consulting GmbH
Mittenhuber Straße 4, 92318 Neumarkt
Phone: +4915224685061
Email: Compliance.EU@outlook.com

For any product support, warranty inquiries, or technical assistance, please contact your seller or the manufacturer directly.

A PDF version of the user manual is available for download: View PDF Manual

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.