SHIMANO RD-M3100-SGS

Contents

SHIMANO Alivio M3100 9-Speed Rear Derailleur User Manual

Model: RD-M3100-SGS

Brand: SHIMANO

Important Safety Information

General Safety Precautions

  • This dealer's manual is intended primarily for use by professional bicycle mechanics. Users who are not professionally trained for bicycle assembly should not attempt to install the components themselves using the dealer's manuals. If any part of the information on the manual is unclear to you, do not proceed with the installation. Instead, contact your place of purchase or a local bicycle dealer for their assistance.
  • Make sure to read all instruction manuals included with the product.
  • Do not disassemble or modify the product other than as stated in the information contained in this dealer's manual.
  • For safety, be sure to read this dealer's manual thoroughly before use, and follow it for correct use.
  • Be sure to follow the instructions provided in the manuals when installing the product.
  • It is recommended to use genuine Shimano parts only. If parts such as bolts and nuts become loose or damaged, the bicycle may suddenly fall over, which may cause serious injury.
  • If adjustments are not carried out correctly, problems may occur, and the bicycle may suddenly fall over, which may cause serious injury.
  • Be sure to wear safety glasses or goggles to protect your eyes while performing maintenance tasks such as replacing parts.

Danger, Warning, and Caution Indicators

DANGER:

Failure to follow the instructions will result in death or serious injury.

WARNING:

Failure to follow the instructions could result in death or serious injury.

CAUTION:

Failure to follow the instructions could cause personal injury or physical damage to equipment and surroundings.

Setup and Installation

Rear Derailleur Installation (MTB/Trekking)

Install the rear derailleur using a 5 mm hexagon wrench.

Tightening torque: 8-10 N-m.

Diagram showing installation of rear derailleur on a bicycle frameImage description: Diagram illustrating the attachment of the rear derailleur to the bicycle dropout and bracket using a 5mm hexagon wrench.

Notice: Periodically check that there is no gap between the derailleur hanger and the bracket. A gap can lead to gear shifting performance issues.

Rear Derailleur Installation (Road)

Install the rear derailleur using a 5 mm hexagon wrench.

Tightening torque: 8-10 N-m.

Notice: Make sure to insert the hexagon wrench all the way into the bracket axle tool hole when tightening. Do not use a ball point hexagon wrench. Incorrect tightening can deform the tool hole or lead to suboptimal gear shifting performance.

Chain Length Adjustment

For largest sprocket 27T or smaller (Road)

Place the chain on the largest chainring and smallest sprocket. The line drawn through the guide pulley and tension pulley should be 90° or greater to the ground.

Diagram for chain length adjustment for 27T or smaller sprocketImage description: Diagram showing the correct chain length for a smallest sprocket of 27 teeth or less, ensuring the guide pulley and tension pulley form a 90-degree angle with the ground.

For largest sprocket 28T or larger (Road)

With the chain put on both the largest sprocket and the largest chainring, add 2 links to determine the minimum number of links that can be connected.

For MTB/Trekking

Mount the chain on the largest sprocket and largest chainring. Add 2 links to set the length of the chain.

The length of the chain will vary depending on the movement of the rear suspension. Ensure the chain length is not too short to avoid excessive load on the drive system.

Diagram for chain length adjustment for MTB/TrekkingImage description: Diagram illustrating chain length adjustment for MTB/Trekking, showing the chain wrapped around the largest sprocket and chainring with an additional two links.

Securing the Cable

Cutting the Outer Casing

Cut the outer casing end opposite the end with the marking. After cutting, make the end round to ensure a uniform diameter inside the hole. Attach a sealed outer cap to the cut end.

Diagram showing how to cut and cap the outer casingImage description: Illustration demonstrating the process of cutting the outer casing and attaching an outer cap.

Connecting and Securing the Inner Cable

Connect the inner cable to the rear derailleur. Remove initial slack by pulling the cable. Reconnect the inner cable to the rear derailleur, ensuring it is securely in the groove.

Tightening torque: 6-7 N-m.

Set the inner cable so that the margin is approximately 30 mm or less. Install the shift inner cap.

Diagram showing inner cable connection to derailleurImage description: Diagram showing the inner cable being connected to the rear derailleur and secured in its groove.

Notice: Check that the inner cable does not interfere with the wheel spokes. Stop the wheel from turning while carrying out this step.

Stroke Adjustment

Top Adjustment

Turn the top adjustment bolt to align the guide pulley with the outer line of the smallest sprocket when viewed from the rear.

Diagram for top stroke adjustmentImage description: Diagram illustrating the top adjustment of the rear derailleur, showing how to align the guide pulley with the smallest sprocket using the top adjustment bolt.

Low Adjustment

Turn the low adjustment bolt so the guide pulley moves to a position directly in line with the largest sprocket.

Diagram for low stroke adjustmentImage description: Diagram illustrating the low adjustment of the rear derailleur, showing how to align the guide pulley with the largest sprocket using the low adjustment bolt.

B-Tension Adjustment

Mount the chain on the smallest chainring and the largest sprocket, and turn the crank arm for shifting.

Adjust the B-tension adjust bolt so that the guide pulley does not interfere with the sprocket but also does not come so close that the chain and pulley contact each other.

Next, set the chain on the smallest sprocket and repeat the process to ensure the pulley does not touch the sprocket.

Check the distance between the largest sprocket and the guide pulley. For 11-42T, 11-36T, 11-34T sprockets, the distance should be 5-6 mm. For 11-32T, the distance should be 9-10 mm.

Diagram for B-tension adjustmentImage description: Diagram showing the B-tension adjustment process, illustrating the correct spacing between the guide pulley and the largest sprocket.

Operating Instructions (SIS Adjustment)

Confirming Positioning on Gear

Operate the shifting lever several times to move the chain to the 2nd sprocket counting from the smallest sprocket.

Then, while operating the lever just enough to close the gap in the lever, turn the crank arm.

The best setting is when the shifting lever is operated just enough to close the lever gap and the chain touches the 3rd sprocket counting from the smallest sprocket and makes noise.

Diagram for confirming gear positioningImage description: Diagram showing the chain's position on the 2nd and 3rd sprockets for confirming gear positioning and identifying noise.

Adjusting SIS (When chain shifts to 3rd sprocket from smallest)

Tighten the cable adjustment barrel until the chain returns to the 2nd sprocket counting from the smallest sprocket (clockwise).

Adjusting SIS (When no sound is generated)

Loosen the cable adjustment barrel until the chain touches the 3rd sprocket counting from the smallest sprocket and makes a noise (counterclockwise).

Return the lever to its original position (2nd sprocket setting) and turn the crank arm clockwise.

If the chain is touching the 3rd sprocket and making a noise, turn the cable adjustment barrel clockwise slightly to tighten until the noise stops and the chain runs smoothly. Stop turning when the noise just stops.

Operate the lever to change gears and check that no noise occurs in any gear positions.

Diagram for SIS adjustment with cable barrelImage description: Diagram illustrating the SIS adjustment process using the cable adjustment barrel to eliminate noise and ensure smooth shifting.

Maintenance

General Cleaning and Lubrication

  • If gear shifting operations cannot be carried out smoothly, clean the derailleur and lubricate all moving parts.
  • Grease the inner cable and the inside of the outer casing before use to ensure they slide properly.
  • Periodically clean the derailleur and lubricate all moving parts (mechanism and pulleys).
  • The gears should be periodically washed with a neutral detergent. Cleaning the chain with neutral detergent and lubricating it can extend the life of the gears and chain.
  • For maximum performance, Shimano lubricants and maintenance products are highly recommended.

Replacing the Pulley

Guide Pulley Replacement

Replace the guide pulley using a 3 mm hexagon wrench.

Tightening torque: 2.5-5 N-m.

Notice: Check the arrow direction on the pulley when installing it.

Diagram for guide pulley replacementImage description: Diagram showing the guide pulley and the process of replacing it with a 3mm hexagon wrench, highlighting the arrow direction for correct installation.

Tension Pulley Replacement

If an E-ring is attached, remove it first.

Replace the tension pulley using a 3 mm hexagon wrench.

Tightening torque: 2.5-5 N-m.

Notice: Check the arrow direction on the pulley when installing it.

Diagram for tension pulley replacementImage description: Diagram showing the tension pulley and the process of replacing it with a 3mm hexagon wrench, highlighting the arrow direction for correct installation.

Troubleshooting

  • Gear Shifting Issues: If gear shifting is not smooth, clean and lubricate the derailleur and all moving parts. Check for excessive looseness in links; if present, replace the derailleur. Ensure the inner cable is greased and the outer casing is not too long or short.
  • Chain Derailment/Noise: If the chain comes off or makes noise, check that adjustments are carried out correctly. Ensure the chain and sprocket combinations do not cause contact and noise (refer to chain length adjustment section).
  • Abnormal Pulley Noise: If abnormal noise is heard from a pulley due to looseness, replace the pulley.
  • High Cable Resistance: A high cable resistance on a frame with internal cable routing can impair SIS shifting. Check the inner cable condition and outer casing bending.
  • Gap between Derailleur Hanger and Bracket: A gap can lead to gear shifting performance issues. Periodically check and ensure no gap exists.

Specifications

FeatureSpecification
Model NumberRD-M3100-SGS
SeriesSHIMANO ALIVIO M3100 Series
TypeRear Derailleur
Rear Speeds9
Compatible ChainHG 9-speed
DesignSHIMANO SHADOW RD (Low-profile)
MountDirect attachment (conventional)
Cable AdjusterYes
Max. Front Difference22T
Total Capacity45T
Low Sprocket (Max)36T
Low Sprocket (Min)32T
Top Sprocket (Max)12T
Top Sprocket (Min)11T
Fluoric Coated Link Bushings1
Pulley Teeth11T
Pulley TypeSunken type pulley screw
B-AxleHollow axle

User Tips

  • Ensure proper installation and adjustment for smooth gear changes and to avoid noise.
  • This derailleur is suitable for a sprocket with an 11-42T ratio.
  • This model is designed for mountain bikes with 9 gears.

Warranty and Support

For support and inquiries, please contact SHIMANO directly:

  • SHIMANO NORTH AMERICA BICYCLE, INC.
    One Holland, Irvine, California 92618, U.S.A.
    Phone: +1-949-951-5003
  • SHIMANO EUROPE B.V.
    High Tech Campus 92, 5656 AG Eindhoven, The Netherlands
    Phone: +31-402-612222
    EU General Contact: contactshimano@shimano-eu.com
  • SHIMANO INC.
    3-77 Oimatsu-cho, Sakai-ku, Sakai City, Osaka 590-8577, Japan

All manuals and technical documents are accessible online at https://si.shimano.com.

Please note: Specifications are subject to change for improvement without notice.

A user manual in PDF format is available for download: User manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.