1. Introduction
The XTOOL D6 Diagnostic Tool interfaces with the Electronic Control Unit (ECU) of a vehicle to retrieve Diagnostic Trouble Codes (DTCs), clear trouble codes, access data stream information, read freeze frame data, and read ECU information. It supports various vehicle control systems such as engine, transmission, Anti-lock Brake System (ABS), Supplemental Restraint System (SRS/Airbag), Chassis, and Body. The device also features full OBD II functions, CAN FD, and FCA protocol support.
This upgraded diagnostic tool is equipped with a dual-core 1.2GHz Processor, 128MB RAM, and 32GB ROM, a 5.45-inch display, and a 3150mAh 3.6V battery for extended use.
The XTOOL D6 includes 18 special functions with lifetime free upgrades, such as Oil Light Reset, EPB, SAS, DPF, BMS Reset, Throttle, TPMS Reset, ABS Bleeding, Injector Coding, Gearbox Match, Suspension, Window Initialization, Headlight, EGR Relearn, and Gear Learning. It can graph up to four live data parameters simultaneously on a single screen.
2. Safety Information
For your safety, the safety of others, and to prevent damage to devices and vehicles, it is crucial to read and understand all safety instructions presented in this manual before operating or coming into contact with the device.
General Safety Instructions:
- Read and Understand: Ensure that all operators and individuals in the vicinity of the device have read and understood the safety instructions.
- Proper Use: Only use the device as described in this manual. Always adhere to the safety messages and test procedures provided by the vehicle or equipment manufacturer.
- Knowledge and Skill: Automotive technicians must be knowledgeable about the system being tested and familiar with proper service methods and test procedures.
- Acceptable Testing Practices: Perform tests in a manner that ensures your safety, the safety of others, and prevents damage to the device and the vehicle.
Specific Responsibilities:
- Refer to Manufacturer Guidelines: Always consult and follow the safety messages and applicable test procedures from the vehicle or equipment manufacturer before using the device.
- Use Appropriate Tools and Techniques: Use the correct tools and techniques for each specific task.
- Anticipate Safety Requirements: Be prepared to handle unforeseen circumstances safely.
Safety Messages:
Danger: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury to the operator or to bystanders.
Warning: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury to the operator or to bystanders.
Safety Instructions for Operation:
- Ventilation: When the engine is running, ensure the service area is well ventilated or connect an exhaust removal system to avoid carbon monoxide inhalation.
- Eye Protection: Always wear safety eye protection that meets ANSI standards.
- Avoid Hazards: Keep clothing, hair, hands, tools, and test equipment away from all moving or hot engine parts.
- Vehicle Preparation: Put the transmission in PARK (automatic) or NEUTRAL (manual) and engage the parking brake. Place blocks in front of the drive wheels.
- Ignition System Caution: Be extra cautious around ignition components (coil, distributor cap, wires, spark plugs) as they generate hazardous voltages.
- Fire Extinguisher: Keep a suitable fire extinguisher nearby.
- Test Equipment Connections: Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
- No Driving While Testing: Do not drive the vehicle and operate the test equipment simultaneously.
- Battery Check: Ensure the vehicle battery is fully charged and the connection to the DLC is clean and secure.
- Avoid Electromagnetic Interference: Do not place the test device on the vehicle's distributor.
3. Setup
3.1 Getting Started
Ensure the Diagnostic Tool is adequately powered by checking its battery status or connecting it to an external power supply.
Turning On:
Press and hold the power button (located on the top right) for approximately five seconds. The tool will power on if the internal battery has sufficient charge or if it's connected to AC power. If the battery is completely drained, charge it for more than 6 hours before turning it on.
Turning Off:
Press and hold the power button for more than three seconds. The tool will automatically power off. Always terminate all vehicle communications before turning off the tool to avoid issues with the ECM.
Emergency Shutdown:
Only use if the Diagnostic Tool is unresponsive or erratic. Press and hold the Power button for at least five seconds. Note: Using emergency shutdown while communicating with the vehicle ECM may cause issues with the ECM.
3.2 Data and Power Connections
The XTOOL D6 Diagnostic Tool can receive power from three sources:
- Internal Battery Pack: Provides power for about 3.5 hours of continuous operation when fully charged. Charging occurs when connected to the AC Power Supply.
- AC Power Supply: Connect the tool to a standard AC outlet using the provided AC power supply. Plug the output cable connector into the DC power supply input jack on top of the Diagnostic Tool. Use only the specified AC power supply.
- 12-Volt Vehicle Power: Locate the vehicle's OBDII port (usually beneath the driver's seat). Insert the 16-pin connector of the OBDII cable into the vehicle's OBDII port, and connect the 15-pin end of the OBDII cable to the device, tightening the nut for a secure connection.
3.3 Main Ports of the Tablet
This diagram illustrates the key physical features and connection points of the XTOOL D6 tablet.
- 5.45-Inch Touch Screen
- Power Button
- VGA 15 PIN-Port
- Type-C Port
- Memory card slot
3.4 Vehicle Connection
The scan tool must be connected to the vehicle's OBD-II port to establish communication. Follow these steps:
- Turn on the tablet.
- Connect the vehicle and tablet using the main test cable.
- Turn on the vehicle's ignition switch to start the diagnostic process.
This image shows the proper connection method between the XTOOL D6 and a vehicle's OBD-II port.
Note: If your vehicle's OBD port is hard to reach, consider purchasing an OBD extension cable.
4. Operating Instructions
4.1 Get to Know the Diagnostic Tool Interface
When the Diagnostic Tool is turned on, the main diagnostic screen will appear:
The main menu provides quick access to all diagnostic and utility functions.
- Auto Scan: Automatically detects and decodes the VIN, then comprehensively scans all available vehicle electronic control modules for diagnostics.
- Diagnosis: Accesses the diagnostic menu, allowing navigation via Auto VIN or manual input of vehicle information for diagnostics.
- OBD-II: Provides standard OBD-II functions including reading/clearing fault codes, monitoring real-time data, and detecting emission system issues.
- Special Functions: Covers commonly performed maintenance services.
- Updates: Allows downloading diagnostic software programs.
- More: Accesses settings for user account, workshop profile, firmware information, diagnostic reports, language, measurement units, etc.
4.2 How to Diagnose Vehicles
The Diagnostic Tool enables communication with a vehicle's electronic control systems to retrieve DTCs, view PID data, and perform advanced functions.
Vehicle Identification:
- Auto Identification: Click "Auto Scan" > "Auto Identification" to automatically scan and decode the vehicle's VIN.
- Manual Input: If automatic scan fails, manually input the VIN.
- Manual Selection: If VIN decoding fails, select "Diagnosis" > region > vehicle brand > "Manual Selection" to manually identify the vehicle.
Note: Auto Identification may not be compatible with all vehicles. Manual Selection is the most reliable option.
4.3 Diagnostic Functions (OBD-II)
The OBD-II function provides access to generic OBD-II data for emission-related diagnostics.
- Read Trouble Code: Displays current, pending, and permanent emission-related DTCs.
- Clear Trouble Code: Erases all emission-related diagnostic data, including DTCs, freeze frame data, and test results. A confirmation screen will appear.
- Live Data (Mode $01$): View real-time emission-related data from the ECM. Parameters and their values are displayed.
- Read Freeze Frame (Mode $02$): Provides a snapshot of critical parameter values at the moment a DTC is set.
- I/M Readiness (Smog Check): Checks the readiness of the monitoring system for emissions compliance.
- O₂S Monitoring Test (Mode $05$): Checks the integrity of oxygen sensors.
- On-Board Monitor Test (Mode $06$): Views results of On-Board Monitor tests.
- Component Test (Mode $08$): Enables bidirectional control of the ECM to test components.
- Read ECU Information (Mode $09$): Displays ECU names, supported protocols, and calibration information.
Live Data Display Options:
- View Waveform Chart: Click the circled area in the diagram to view the waveform chart for each data stream.
- Select Live Data: Click "Custom" to display only selected data streams.
- 4-IN-1 Live Data: Select data streams and click "Custom-Combine" for a combined 4-in-1 graphical data stream. You can select up to four data streams at a time.
This video provides an overview of the XTOOL D6's internal components, ports, and diagnostic capabilities, including live data graphing and special functions.
4.4 Special Functions
The XTOOL D6 offers 15+ crucial vehicle maintenance functions. The availability of these functions may vary by vehicle; always verify compatibility using the vehicle's VIN.
Visual representation of the 15+ special functions available on the XTOOL D6.
- Oil Reset: Resets the engine oil life system after an oil change.
- EPB Reset: Activates/deactivates the electronic parking brake and performs caliper retraction for brake service.
- SAS Reset: Calibrates the steering angle sensor.
- DPF Regen: Initiates Diesel Particulate Filter regeneration.
- BMS Reset: Resets the battery management system after battery replacement.
- Throttle Matching: Resets throttle actuators to default state for accurate air intake control.
- TPMS Reset: Resets the tire pressure monitoring system to recognize new tire pressure values.
- ABS Bleeding: Performs automated ABS brake fluid bleeding.
- Injector Coding: Codes new fuel injectors to the ECU.
- Gearbox Match: Matches the transmission control module with the ECU.
- Suspension: Calibrates the electronic suspension system.
- Window Initialization: Initializes power window regulators.
- Headlight: Performs headlight level calibration.
- EGR Relearn: Relearns EGR valve operation.
- Crank Sensor Relearn: Calibrates the crankshaft position sensor.
- CPS Reset: Performs tooth learning for the vehicle, to turn off the MIL.
4.5 Software Updates
Software updates can be performed while connected to a Wi-Fi network or using a mobile phone's hotspot. It is recommended to use a mobile phone's hotspot if network provider restrictions are present.
To update, navigate to the "Updates" menu. You have two options:
- Update All Software Programs: Click "Update" to update all available programs.
- Update Individual Software Program: Click the update icon next to a specific software program.
Note: If an update is interrupted, click the update icon again to proceed.
4.6 Other Functions
- Print Report: Send diagnostic reports to your email for printing.
- Data Logging: For software-related issues, data logging provides crucial information for technical support. Keep the tool connected to Wi-Fi for at least 15 minutes and provide the Serial Number (S/N) to support.
- FAQ Database: Access the FAQ database on www.xtoolonline.com/faqs.
- Corporate Purchase: For bulk purchases, contact Support@xtoolonline.com.
- Inventors and Testers Program: Contact the company directly for information on becoming a product tester or contributing to language improvements.
5. Maintenance
- Clean Equipment: Keep the test equipment dry, clean, and free from oil, water, or grease. Use a mild detergent on a soft cloth to clean the exterior.
- Battery Charging: Ensure the internal battery is charged regularly, especially if completely drained, requiring over 6 hours for a full charge.
- Software Updates: Regularly update the software to ensure optimal performance, access to the latest features, and compatibility with new vehicle models.
- Storage: Periodically check the device's storage space and clear cache to maintain performance.
6. Troubleshooting
- Emergency Shutdown: Use only if the tool is unresponsive. Press and hold the Power button for at least five seconds.
- Auto Identification/VIN Scan Failure: If automatic VIN detection fails, try manual VIN input or manual vehicle selection.
- Network/Wi-Fi Connection Issues: Ensure your router uses WPA2 (not WPA3 for maximum compatibility) and does not block outgoing traffic to non-US regions. Try a mobile hotspot. If the device shows "connect internet to sync your device," check if the Android system's country and time zone match the network time zone (e.g., Pacific time zone).
- Battery Not Charging:
- Use the original charging cable or OBD test cable to charge for more than six hours.
- Hold the shutdown button for 15 seconds to see if it turns on (without charging cable).
- Connect to a computer via USB to check if it's recognized.
- If issues persist, contact technical support.
- Device Frozen: If the device freezes, try the reset button or power button. If it remains frozen, ensure the app is updated to the latest version. If updated, perform a factory reset. If the problem persists, contact support.
- Lock Screen Password Issue: If you received a used device with a lock screen password, contact support with the device's S/N to resolve.
- Functions Not Available on All Vehicles: Not all tools support all functions on all vehicles due to varying vehicle configurations and manufacturer specifications.
7. User Tips
- Fast and Responsive: Users report the XTOOL D6 is fast, responsive, and offers many functions, making it a reliable diagnostic tool.
- Effective for Complex Issues: This device has been noted for successfully resolving complex vehicle issues, particularly with Chinese car models, due to its diagnostic and programming capabilities.
- Monthly Internet Connection: It is a government policy compliant requirement to connect the device to Wi-Fi once a month. This helps report IP location and prevents the device from being used for illegal activities.
8. Technical Specifications
| Item | Description/Specification |
|---|---|
| Display | 5.45 Inch (1440*720 Resolution) |
| Operating System | Linux |
| Protocols Supported | CAN FD/FCA |
| Processor | Dual-core 1.2 GHz |
| Memory | 128M+32G |
| Connectivity | Type-C |
| Operating Method | Flat Panel Touchscreen |
| Upgrade Method | Device Connects to Wi-Fi for Online Upgrade |
| Battery | 3150mAh 3.6V |
| Wi-Fi | 2.4G/5Ghz |
| Tested Battery Life | 3.5 Hours |
| Dimensions | 19.5*2.8*11.5(CM) |
| Free Renewal Update | Lifetime |
| Charging Method | Type-C Charging (No charger included) |
| Sensor | Gravity/Light Sensor |
| Audio | Microphone |
| Speaker | Built-In Speaker |
| Weight (Including Battery) | 0.4KG |
| Gross Weight | 0.8KG |
| Operating Temp Range (Ambient) | -4°F ~ 140°F (-20°C ~ 60°C) |
| Storage Temp (Ambient) | -40~158°F (-40~70°C) |
| Operating Humidity | <90% |
8.1 What's In The Box
Contents of the XTOOL D6 product package.
| Name | QTY |
|---|---|
| Tablet | 1 |
| VGA to OBD-II-16 Main Cable | 1 |
| Quick Guide | 1 |
| Packing List | 1 |
| Color Carton | 1 |
| USB Type-C Main Cable | 1 |
9. Warranty & Support
9.1 Limited Two-Year Warranty
Shenzhen XTOOL tech Intelligent Co., LTD. (the Company) warrants to the original retail purchaser of this XTOOL device that should this product or any part thereof during normal usage and under normal conditions be proven defective in material or workmanship that results in product failure within two years from the date of purchase, such defect(s) will be repaired, or replaced (with new or rebuilt parts) with Proof of Purchase, at the Company's option, without charge for parts or labor directly related to the defect(s).
The Company shall not be liable for any incidental or consequential damages arising from the use, misuse, or mounting of the device.
This warranty does not apply to:
- Products subjected to abnormal use or conditions, accident, mishandling, neglect, unauthorized alteration, misuse, improper installation/repair or, improper storage.
- Products whose mechanical serial number or electronic serial number has been removed, altered, or defaced.
- Damage from exposure to excessive temperature or extreme environmental conditions.
- Damage resulting from connection to, or use of any accessory or other product not approved or authorized by the Company.
- Defects in appearance, cosmetic, decorative, or structural items such as framing and non-operating parts.
- Products damaged from external causes such as fire, dirt, sand, battery leakage, blown fuse, theft, or improper usage of any electrical source.
9.2 Technical Assistance
- Website: https://www.xtoolonline.com
- Email Support: support@xtoolonline.com
- Corporate & Business: business@xtoolonline.com, sales@xtoolonline.com
- Address: Room 601, Block A, Zaoan Business Building, Shigu Road, Xili Residential District, Nanshan District, Shenzhen
9.3 Product Training Videos
Diagnostic Tool specific training videos are available on the XTOOL website. Follow along and learn the basics of Diagnostic Tool operation. Videos are product specific and can be found at: https://www.xtoolonline.com/support/product-videos. Click on the "Support" > "Product Videos" > "Diagnostic Tools" tab, select the applicable Diagnostic Tool, then select the training video you want to watch.
9.4 Compliance Information
- FCC Compliance / FCC ID: 2AW3IF510: This device complies with Part 15 of the FCC rules and Industry Canada's license-exempt RSSs.
- UKCA: (UK Conformity Assessed) compliance mark.
- RF Warning Statement: The device has been evaluated to meet general RF exposure requirements.
- ROHS Compliance: Complies with European RoHS Directive 2011/65/EU.
- CE Compliance: Conforms to EMC Directive 2014/30/EU, R&TTE Directive 1999/5/EC, Low Voltage Directive 2014/35/EU.
- ISED: (Innovation, Science and Economic Development Canada) compliance.