1. Introduction
This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your Ajazz GP100 Wireless Gamepad. Please read this manual thoroughly before using the product to ensure optimal performance and longevity.
Product Overview
The Ajazz GP100 is a versatile wireless gamepad designed for a wide range of gaming platforms, including PC, Nintendo Switch, Android, and iOS devices. It supports multiple connection methods: Bluetooth (BT), 2.4G wireless dongle, and wired USB. Key features include a high-precision Hall 3D joystick, customizable M1/M2 macro buttons, rapid-fire functionality, adjustable vibration, 6-axis gyroscope, and dynamic RGB lighting effects.
Product Features
- PC functions: rapid fire, motor vibration adjustment, M1/M2 mapping, and macro functionality.
- Four LED status indicators: Red/White/Green/Blue.
- 18 functional buttons with a three-mode switch (NS/BT/Dongle).
- Built-in dual motors, high-precision Hall 3D joystick with switch conversion function.
- Two customizable M1/M2 buttons on the back for mapping and macro functions.
- 6-axis gyro for fast and accurate target locking.
- Wired connection to PC for software upgrades and X/D-INPUT/NS mode support.
- RGB lighting effects on both sides with four 1615 RGB lights per side.
- Automatic sleep mode after 5 minutes of inactivity (60 seconds if pairing fails).
- Charging via Type-C port or charging dock.
- 1000 Hz polling rate when connected via cable to PC or wirelessly with the dongle.
- App compatibility.
2. Component Identification
Front View
- HOME Button: Power on/off, sleep mode.
- View Button / "-" Button: View function (PC/Android/iOS), "-" button (Nintendo Switch).
- Menu Button / "+" Button: Menu function (PC/Android/iOS), "+" button (Nintendo Switch).
- Action Buttons (X, Y, A, B): Standard action buttons.
- Left Joystick / L3: Left analog stick, press for L3 button.
- Right Joystick / R3: Right analog stick, press for R3 button.
- D-Pad: Directional pad.
- RGB Lighting: Four RGBs on each side (left and right).
- LED Indicators:
- White LED (top left)
- Blue LED (top right)
- Green LED (bottom left)
- Red LED (bottom right)
- These indicate low voltage, charging status, and pairing status.
- Motor Setting Button: Rapid fire, motor vibration adjustment, screenshot function (Nintendo Switch).
Top and Bottom Views
- ZR, R, L, ZL Buttons: Shoulder and trigger buttons.
- Type-C Port: For wired connection and charging.
- Right Board Long/Short Switch: Adjusts trigger travel for the right trigger.
- Left Board Long/Short Switch: Adjusts trigger travel for the left trigger.
- M1, M2 Buttons: Customizable back buttons.
- Mode Switch: Selects connection mode (NS/BT/Receiver).
3. Setup Instructions
3.1. NS Mode Connection (Nintendo Switch)
Initial Wireless Pairing
- Set the mode switch on the gamepad to "NS" mode.
- Press and hold the HOME button on the controller for 3 seconds until the white LED indicator flashes rapidly.
- On your Nintendo Switch console, open the pairing menu.
- Perform Bluetooth pairing. Once successfully paired, all controller functions will work, and the console-assigned channel light will remain steady.
- If pairing fails, the controller will automatically enter sleep mode after approximately 60 seconds. If paired successfully but left idle, the controller will automatically sleep after about 5 minutes.
Wired Guidance for BT Pairing
- Connect the controller to the Nintendo Switch console via a USB data cable.
- Press any button on the controller to wake it up.
- Once the data cable is disconnected, the controller will automatically connect to the Nintendo Switch console via Bluetooth.
- Up to four controllers can connect simultaneously to the NS console, with assigned channel lights (Red/White/Green/Blue LEDs remaining steadily lit).
3.2. BT Mode Connection (Android/iOS/Laptops)
When the controller is in sleep mode:
Android Devices
- Turn on Bluetooth settings on your Android device (phone, TV, etc.).
- Switch the controller mode to "BT" mode.
- Press and hold the HOME button on the controller for 3 seconds until the status indicator LED flashes blue rapidly, indicating pairing mode.
- Search for "Xbox Wireless Controller" on your device and connect.
- Once paired, the Red LED will stay lit.
iOS Devices
- Ensure the controller is in sleep mode and the mode switch is in the "BT" position.
- Press and hold the HOME button for 3 seconds. The blue LED will flash rapidly, indicating pairing mode.
- Search for "Xbox Wireless Controller" on your iOS device and connect.
- Once paired, the Red LED will stay lit. The controller will automatically reconnect to the last paired Android or iOS device when woken up (with the mode switch in "BT" position).
Laptops
- Ensure the controller is in sleep mode and the mode switch is in the "BT" position.
- Press and hold the HOME button for 3 seconds. The blue LED will flash rapidly, indicating pairing mode.
- Search for "XBOX Wireless Controller" on your laptop and connect.
- Once paired, the blue LED will stay lit.
3.3. Dongle Mode Connection (PC)
Direct Dongle Connection
- Set the controller mode switch to the dongle position.
- While the controller is in sleep mode, press and hold the HOME button for 3 seconds until the red LED flashes rapidly.
- Plug the dongle into your PC's USB port.
- Press the "Pairing" button on the dongle for 3 seconds until its green LED flashes rapidly.
- The dongle and controller will pair. Once connected, the dongle's green LED and the controller's red LED will stay lit.
- If pairing fails, the controller will enter sleep mode after 60 seconds. If successful but idle, it will sleep after 5 minutes.
- The dongle operates in X-INPUT mode by default. Press and hold the +/- buttons for 3 seconds to switch to D-INPUT or NS mode.
Dongle Connection via Charging Dock
- Connect the charging dock to your PC via the Type-C port.
- Plug the dongle into the USB port on the charging dock.
- Switch the controller mode to the dongle position.
- When the charging dock is charging the controller, a charging indicator will be displayed.
- When the controller is picked up, it will automatically reconnect to the dongle.
- For first-time pairing: While the controller is in sleep mode, press and hold the HOME button for 3 seconds until the red indicator flashes rapidly. Simultaneously, press and hold the receiver's "pairing button" for 3 seconds until the green LED flashes rapidly.
- Once paired, the dongle can connect to the PC through the charging dock.
- The dongle operates in X-INPUT mode by default. Press and hold the +/- buttons for 3 seconds to switch to D-INPUT or NS mode.
Bluetooth Receiver Connection (PC)
- After connecting the controller to the Bluetooth receiver, it supports X-INPUT functionality by default. The system assigns a solid red indicator LED, and the device name appears as "GP100" (requires Xbox 360 drivers installed on PC).
- To switch to NS mode, press and hold the +/- buttons for 3 seconds. The system assigns a solid blue indicator LED, and the device name will be "GP100".
- To switch to D-INPUT mode, press and hold the +/- buttons for 3 seconds. The device will be "GP100," and the controller's indicator light will stay lit with both red and blue lights.
3.4. GameMacro APP Installation
- Open your mobile phone or tablet.
- Use WeChat to scan the QR code below to download the "GameMacro APP".
- Find the Bluetooth name related to GameMacro in your phone's Bluetooth list and connect to pair.
- After entering the app, tap the "+" icon in the top left corner, select the controller that was just connected via system Bluetooth, and complete the connection.
4. Operating Instructions
4.1. "HOME" Button Operation
To put the controller into sleep mode when powered on, press and hold the "HOME" button for 5 seconds.
4.2. Customizing M1/M2 Buttons (Mapping & Macros)
The controller's back buttons, M1 and M2, can be customized. The following function buttons can be mapped: UP, DOWN, LEFT, RIGHT, A, B, X, Y, L1, R1, ZL, ZR, "-", "+", and any direction of the left and right 3D joysticks.
Mapping Process
- After connecting to NS/BT/Receiver, hold M + M1. The left RGB light will slowly flash white, indicating entry into mapping mode.
- Once in M1 customization mode, press a button (e.g., "A"). Then press M1 again; the RGB light will flash once, confirming that "A" is now mapped to M1.
- Follow the same steps for M2.
- You can assign multiple function keys to M1 (M2) by holding M + M1 and inputting keys sequentially. When pressed in-game, the macro will execute based on the time intervals between the input keys.
- Each M1/M2 macro can store up to 16 key inputs.
Clearing M1 & M2 Customization
While connected to a Nintendo Switch console or PC, repeat the mapping steps to clear the customized feature of M1. The M2 function clearing process is the same as M1. After clearing, the button will have no assigned function. (Custom settings are saved after shutdown; however, a factory reset will remove all custom functions assigned to M1 and M2.)
4.3. Turbo (Rapid-fire) Function
Enabling Turbo
Hold down the "M" button and press one of the function buttons (A/B/X/Y, L1/R1, ZL/ZR) to enable the rapid-fire function. It will have a turbo function with light indicators. The TURBO button functionality applies to these eight keys.
Switching Turbo Modes
After setting the rapid-fire function, you can switch between manual rapid-fire, automatic rapid-fire, or single shot.
Canceling Turbo
To cancel the rapid-fire function for a specific key, repeat the steps above or hold down the "M" button for 5 seconds.
Adjusting Turbo Speed
Hold the M button + move the right joystick up/down to adjust the turbo speed between three levels: Fast, Medium, and Slow. (Turbo speed settings and key values are saved after shutdown. However, if a factory reset is performed, any custom functions assigned to the TURBO button and turbo speed settings will be cleared, restoring the default medium speed and single-shot mode.)
4.4. Trigger Short and Long Stroke Operation
The GP100 features Hall double-cut triggers, allowing for one-click switching between linear and micro-motion modes.
- Long Travel Mode: Pressing the left or right trigger provides an analog function with a range from 1 to 255, accompanied by vibration feedback.
- Short Travel Mode: Pressing the left or right trigger immediately reaches 255, also accompanied by vibration feedback.
4.5. RGB Lighting Effect Settings
Note: RGB lighting effects can only be adjusted when the controller is connected to the NS console or PC via wired/wireless connection. RGB effects cannot be adjusted while the controller is charging on the dock.
Lighting Modes
- Mode 1: Rainbow mode (default).
- Mode 2: Lightning mode. Simultaneously press the left and right 3D buttons once (L3, R3) to switch the light color combination.
- Mode 3: Multi-color cycling breathing mode.
- Mode 4: In this mode, simultaneously press the left and right 3D buttons once (L3, R3) to switch the light color combination.
Adjusting Brightness
You can adjust the brightness of the RGB lighting with four levels: 25%, 50%, 75%, and 100%.
- Decrease Brightness: M + left joystick right direction.
- Increase Brightness: M + left joystick left direction.
Turning RGB Lighting On/Off
- Turn Off: Press and hold M + "R3" for 5 seconds.
- Turn On: Press and hold M + "R3" for 5 seconds again.
The current state is saved after powering off. Press the M button + "R3" button briefly (pause for 100 microseconds) once to switch to one RGB lighting effect, cycling through Mode 1, Mode 2, Mode 3, Mode 4, and then back to Mode 1 (in a loop). (The lighting settings are saved after powering off. Restoring factory settings will clear the lighting settings, with the default set to Rainbow mode.)
4.6. Menu and M Button Functions
- PC or Android/iOS: The View button acts as the View function, the Menu button acts as the Menu function, and the "M" button has rapid-fire and motor vibration adjustment functions.
- Nintendo Switch: The View button acts as the "-" button, the Menu button acts as the "+" button, and the "M" button serves as the screenshot function. To activate the screenshot function, the "M" button must be pressed twice.
4.7. Charging
Using the Charging Dock
- Place the controller into the included charging dock. The four charging contacts at the bottom of the controller will enable charging.
- The charging dock can be powered by an external power supply or an adapter via its Type-C input port.
- When the base is charging the handle, the RGB indicator light will be on and off when fully charged.
- When the base is charging the handle, pressing the handle's M key + R3 key can change the charging light effect of both.
- Charging light effect: when the charger is charging for the handle, the two indicator lights will be the same tone of breathing and flashing. When fully charged, the RGB light effect will close.
Direct Type-C Charging
- Plug the controller into the Type-C port to charge it.
- The channel light will glow a constant red LED and will switch off once charging is complete.
- If charging while connected to a device, the channel light will display a slowly flashing red LED and turn off when fully charged.
Note: The Type-C input port has an over-voltage protection function. If the input voltage exceeds 6V + 0.2V, the charger will not output voltage, and the RGB indicator light will be off.
4.8. Low Battery Alert
When the controller's battery voltage drops below 3.5V, the channel's red LED will flash rapidly, indicating low battery and the need for charging.
4.9. Standby
- To enter sleep mode: Press and hold the "HOME button" for 5 seconds.
- Automatic sleep (pairing failure): If pairing fails within 60 seconds, the controller will automatically enter sleep mode.
- Automatic sleep (inactivity): If the controller is connected but remains inactive for approximately 5 minutes, it will automatically enter sleep mode.
4.10. Receiving Distance
The effective wireless reception distance of the controller is within 10 meters.
5. Maintenance
5.1. Reset Function
If the controller malfunctions, you can reset it by pressing the reset button through the reset hole (usually a small pinhole on the back or bottom of the controller).
5.2. Controller Firmware Upgrade
If certain functions become unavailable due to a console system upgrade or if a functional update is required, the controller firmware can be upgraded via a PC.
- Download the firmware upgrade software (e.g., "GDF-G560637_74A7_V1.0_250110.exe").
- When the controller is in sleep mode or powered on, connect it to the PC using a USB cable.
- Simultaneously press and hold HOME + X + Y for 3 seconds to enter upgrade mode (the "Online" indicator in the software will turn green).
- The "Update Firmware" button in the software will change from gray to black. Click "Update Firmware" to proceed.
- During the upgrade, ensure the data cable remains stably connected. Once complete, the software will indicate success.
5.3. 3D Joystick/Gyroscope Factory Calibration
This calibration is performed when the controller is in sleep mode.
- Press L3 + R1 simultaneously to enter joystick and trigger calibration. The red and green lights will flash alternately.
- Rotate the joystick forcefully for 2 full circles.
- Press the trigger all the way down 2 times.
- Place the controller on a flat surface and press the A button again to complete the calibration.
- The controller will automatically proceed to motion calibration (flashing blue light) and then return to sleep mode.
5.4. Calibrating the Controller's Gyroscope Sensor on SWITCH Console
- After connecting to the Nintendo SWITCH console, go to the main menu and select "Settings".
- Scroll down to "Controllers and Sensors" and then select "Calibrate Motion Controls".
- In the pop-up menu, click "Calibrate Controller".
- Place the controller on a flat surface and follow the on-screen instructions.
- Press and hold the "-" or "+" button on the controller to complete the gyroscope calibration.
5.5. Calibrating the 3D Joystick with the SWITCH Console
- After connecting to the Nintendo SWITCH console, go to the main menu and select "Settings".
- Scroll down to "Controllers and Sensors" and then select "Calibrate Control Sticks".
- Follow the on-screen instructions and press the joystick you want to calibrate.
- Press the "X" button on the controller to display the prompt menu, then press the "A" button to confirm the calibration.
- Once in the "Calibrate Control Stick" interface, perform the calibration actions according to the on-screen instructions: move the joystick up, down, left, right, and draw circles.
6. Troubleshooting
- Controller not pairing: Ensure the controller is in the correct mode (NS, BT, or Dongle) and that the indicator LEDs are flashing rapidly. If pairing fails, the controller will enter sleep mode after 60 seconds. Try re-initiating the pairing process.
- Controller not responding: Perform a reset by pressing the reset button through the reset hole.
- Controller not waking up: If the controller is in factory lock mode, all buttons are disabled for wake-up. To exit factory lock mode, charge the controller using a USB data cable at least once.
- Firmware-related issues: If certain controller functions fail to work properly due to a Switch system version update, or if a functional update is required, perform a firmware upgrade via PC as described in Section 5.2.
- GameMacro APP connection issues: If the connection fails for any reason, the app may display a troubleshooting page. Ensure your phone's system Bluetooth and the controller are already paired. You can also try reconnecting from the history list in the app.
- Charging issues: Ensure the Type-C cable or charging dock is properly connected. If using the charging dock, ensure the input voltage is within the specified range (not exceeding 6V + 0.2V).
7. Specifications
| Feature | Detail |
|---|---|
| Product Branding | Ajazz |
| Product Model | GP100 |
| Connection | BT 5.3, Wired, 2.4G |
| Applicable Platforms | PC, Switch, Android, iOS |
| Trigger Type | Two-stage Hall linear trigger with trigger lock to switch between long and short strokes. |
| Joystick Type | Custom Hall Joystick (500W life) |
| Stick Polling Rate | Wired with 2.4G receiver 1000Hz |
| Vibration Motor | Rotor motors of the same type for Xbox |
| ABXY Key | 200W sub-life silent adhesive conduction button |
| Shoulder Button Type | Silent conductive silicone keys |
| D-pad Type | Silent conductive silicone keys (Seven-layer eight-direction cross key) |
| Button Layout | Detachable keys, Xbox and S layouts are interchangeable. |
| Combo Function | Yes |
| Battery Capacity | 800mAh |
| AB/XY Key-value Swapping | Yes |
| Product Dimensions | 156mm x 106mm x 59mm (6.14in x 4.17in x 2.3in) |
| Product Weight | 256g (0.56 lbs) |
| Power Supply | Built-in polymer battery |
| Usage Time | Approximately 6 to 8 hours of continuous use |
| Charging Time | Approximately 3 hours |
| Charging Voltage | DC5V |
| Charging Current | 390mA |
| Operating Current | 290mA (Max current with motor vibration and RGB at max) |
| Sleep Mode Current | Less than 20µA |
| Pairing Current | Less than 45mA |
| Package Dimensions | 18cm (L) x 14cm (W) x 8cm (H) |
| Package Weight | 0.536 kg (1.18 lbs) |
8. Warranty and Support
For any issues related to firmware updates or if certain controller functions fail to work properly due to a console system update, please contact Ajazz customer support to obtain the necessary software and upgrade instructions.
A user manual in PDF format is available for download: Ajazz GP100 User Manual (PDF)
9. User Tips
- Button Feel: The clicky mechanical buttons offer a responsive and less tiring experience compared to traditional rubber buttons.
- D-Pad Precision: The larger, protruding D-pad design provides enhanced precision for directional inputs.
- ABXY Buttons: The mouse-like ABXY buttons are designed for fast, repeated clicks, beneficial for competitive gaming.
- Joystick Performance: Features strong magnets in the joysticks for improved feel and control.
- Trigger Customization: The RT and LT buttons have a shorter travel distance and can switch to a clicky mode for quick actuation.
- Compatibility: The controller is compatible with PC, Nintendo Switch, Android, and iOS. While not officially listed for PS3 or Xbox, some users have inquired about compatibility. For PC, ensure Xbox 360 drivers are installed for X-INPUT mode.
- Software: While the controller is highly functional, it does not come with dedicated PC configuration software. Settings are primarily adjusted via button combinations or the GameMacro app.
- Charging Dock: If your package did not include a charging dock, contact customer support. The controller can still be charged directly via a Type-C cable.
10. Product Video Overview
Watch this video for a quick overview of the Ajazz GP100 Gamepad's key features, including Hall Effect joysticks, Xbox layout, RGB lighting, multiple connection options, and ergonomic design.