1. Introduction

1.1 Overview
The AV Access HDW100 is a 1080P wireless HDMI extender kit designed to extend HDMI signals from a source device to a display device. It supports wireless transmission up to 200 meters (656 feet) and wired transmission via a Cat 5e/6 cable up to 120 meters (394 feet). This extender is suitable for various applications in homes and offices.
1.2 Features
- Transmits 1080P HDMI signals wirelessly up to 200m (656ft).
- Transmits 1080P HDMI signals via Cat 5e/6 cable up to 120m (394ft).
- Features an HDMI loop-out on the transmitter for local display monitoring of the source signal.
- Includes IR extension for remote control of the source device from the receiver location.
- Supports automatic optimal channel selection for stable wireless network signals.
2. Package Contents
Before installation, please verify that all items listed below are included in your package:
- Transmitter (TX) x 1
- Receiver (RX) x 1
- Antennas x 2
- Power Adapters (DC 5V 1A) x 2
- Exchangeable US Plugs x 2
- IR Emitter x 1
- Broadband IR Receiver (30-50KHz) x 1
- Mounting Ears (with Screws) x 4
- User Manual x 1

3. Product Panel Layout
Familiarize yourself with the ports, indicators, and switches on both the Transmitter and Receiver units.
3.1 Transmitter Panel
- Power Connector (DC 5V): Connects to the power adapter.
- Power LED: Indicates power status.
- Link LED: Indicates connection status.
- HDMI In LED: Indicates HDMI input signal status.
- Reset Key & LED: For resetting the device.
- HDMI In: Connects to the HDMI source device.
- HDMI Out (Loop Out): Connects to a local display for monitoring.
- IR Out: Connects to the IR Emitter.
- LAN: Ethernet port for wired transmission.
- Antenna: Connects to the antenna for wireless transmission.
- Work Mode Switch: Toggles between "Wireless" and "Wire" modes.
3.2 Receiver Panel
- Power Connector (DC 5V): Connects to the power adapter.
- Power LED: Indicates power status.
- Link LED: Indicates connection status.
- Reset Key & LED: For resetting the device.
- HDMI Out: Connects to the display device.
- IR In: Connects to the IR Receiver.
- LAN: Ethernet port for wired transmission.
- Antenna: Connects to the antenna for wireless transmission.
- Work Mode Switch: Toggles between "Wireless" and "Wire" modes.

4. Installation and Application
4.1 Bracket Installation
Note: Before installation, ensure the device is disconnected from the power source.
- Position and install the mounting brackets using the provided mounting screws. Repeat this step for the other side of the device.
- Attach the brackets to the desired surface using appropriate screws (not included).
4.2 Connection Diagrams
4.2.1 Wireless Transmission Setup
For wireless operation, ensure the "Work Mode" switch on both the Transmitter and Receiver is set to "Wireless".

4.2.2 Wired Transmission Setup
For wired operation, ensure the "Work Mode" switch on both the Transmitter and Receiver is set to "Wire". Connect a Cat 5e/6 Ethernet cable between the LAN ports of the Transmitter and Receiver.

5. Operating Instructions
5.1 Power On
Connect the provided DC 5V 1A power adapters to both the Transmitter and Receiver units. The Power LED on each unit will illuminate.
5.2 Selecting Work Mode
Use the "Work Mode" switch on both the Transmitter and Receiver to select your desired operation mode:
- Wireless Mode: For extending HDMI signals wirelessly up to 200m. Ensure both units are set to "Wireless".
- Wired Mode: For extending HDMI signals via a Cat 5e/6 cable up to 120m. Ensure both units are set to "Wire" and connected via an Ethernet cable.
5.3 Signal Transmission
Once powered on and the work mode is selected, the Link LED will indicate a successful connection between the Transmitter and Receiver. The HDMI In LED on the Transmitter will light up when an HDMI source is connected and active. The system will automatically search for the best wireless channel to ensure optimal signal quality.

5.4 IR Control
Connect the IR Emitter to the "IR Out" port on the Transmitter and position its head near the IR sensor of your source device (e.g., DVD player). Connect the IR Receiver to the "IR In" port on the Receiver and place it in a location where your remote control can easily send signals to it. This allows you to control the source device from the remote display location.
5.5 HDMI Loop-Out
The Transmitter unit includes an HDMI loop-out port, allowing you to connect a local display (e.g., a TV in the same room as the source) to monitor the content being transmitted.
6. Specifications
6.1 Technical Specifications
| Feature | Description |
|---|---|
| Input A/V Port | Transmitter: 1 x HDMI Receiver: 1 x LAN, 1 x WLAN |
| Input Resolutions | Up to 1080P@60Hz |
| Output A/V Port | Transmitter: 1 x HDMI (Loop Out), 1 x LAN, 1 x WLAN Receiver: 1 x HDMI |
| Output Resolutions | Up to 1080P@60Hz |
| Compliance | HDMI 1.3, HDCP 1.4 |
| Transmission Distance | Wireless: 200m/656ft (line of sight) Wired: 120m/394ft |
6.2 General Specifications
| Feature | Description |
|---|---|
| Operating Temperature | +32°F ~ +113°F (0°C ~ +45°C) 10% ~ 90%, non-condensing |
| Storage Temperature | -4°F ~ 140°F (-20°C ~ +70°C) 10% ~ 90%, non-condensing |
| Power Supply | DC 5V 1A |
| Power Consumption | TX: 3.5W (Max) RX: 1.6W (Max) |
| ESD Protection | Human body model: ±8kV (air-gap discharge)/±4kV (contact discharge) |
| Product Size (W x H x D) | 140mm x 21mm x 80mm / 5.5" x 0.83" x 3.15" each for TX and RX (Antennas not included) |
| Net Weight | TX: 0.31kg; RX: 0.30kg |
| Gross Weight | 1.10kg |
7. Troubleshooting
If you encounter issues with your AV Access HDW100 extender, please refer to the following common troubleshooting steps:
- No Signal/Poor Picture Quality:
- Ensure all HDMI cables are securely connected.
- Verify that the "Work Mode" switch on both units is set correctly (Wireless or Wire) for your connection type.
- In wireless mode, check for obstructions between the transmitter and receiver. Try repositioning the units or antennas for a clearer line of sight.
- Ensure the power adapters are correctly connected and both units are powered on.
- Try a different HDMI cable or display to rule out external component issues.
- If using wired mode, check the Ethernet cable for damage and ensure it's a Cat 5e/6 cable.
- IR Control Not Working:
- Ensure the IR Emitter is correctly plugged into the Transmitter's "IR Out" port and positioned directly over the source device's IR sensor.
- Ensure the IR Receiver is correctly plugged into the Receiver's "IR In" port and is in a clear line of sight of your remote control.
- Check the batteries in your remote control.
- Units Not Linking:
- Confirm both units are powered on and their "Work Mode" switches match.
- Press the Reset button on both units simultaneously to re-establish the connection.
- Reduce the distance between the units or remove any interference sources.
If problems persist, please contact AV Access customer support.
8. User Tips
Based on user experiences, here are some tips for optimal performance:
- For wireless connections, maintaining a clear line of sight between the transmitter and receiver is crucial for maximum range and stability. Walls and other obstacles can significantly reduce performance.
- When using the IR control feature, experiment with the placement of the IR emitter over your source device's IR sensor to find the most effective position.
- Consider using the wired mode (Cat 5e/6 cable) for installations where wireless interference is high or a more stable, long-distance connection is required.
- Always power on the source device and display before powering on the extender units to ensure proper HDMI handshake.
9. Maintenance
To ensure the longevity and optimal performance of your AV Access HDW100 extender, please follow these maintenance guidelines:
- Cleaning: Wipe the devices with a dry, soft cloth. Do not use liquid or aerosol cleaners.
- Environment: Avoid using the product in extremely hot, cold, dusty, or humid environments.
- Handling: Handle the devices with care. Avoid dropping or subjecting them to severe impacts, which can cause mechanical damage or malfunction.
- Disassembly: Do not attempt to open, disassemble, or repair the product yourself. Unauthorized repairs will void the warranty and may cause damage to the device or personal injury.
10. Safety Information
Please read and adhere to the following safety precautions:
- Do not open, disassemble, or repair this product. There are no user-serviceable parts inside.
- Do not use the device in hot, cold, dusty, or humid environments.
- Wipe the device with a dry cloth only.
- Avoid dropping the device. Severe impact may cause mechanical damage, malfunction, or scratches.
- Ensure proper ventilation around the units to prevent overheating.
- Use only the provided power adapters. Using unauthorized power adapters may damage the device and void the warranty.
11. Warranty and Support
11.1 Limited Warranty
AV Access products are backed by a limited 1-year parts and labor warranty. Service charges may apply if the product is still remediable but the warranty card is unenforceable or inapplicable under the following conditions:
- The original serial number (specified by AV Access) labeled on the product has been removed, erased, replaced, defaced, or is illegible.
- The warranty period has expired.
- Defects are caused by repairs, dismantling, or alterations performed by unauthorized personnel.
- Defects are caused by improper use, rough handling, or failure to follow instructions in the User Guide.
- Defects are caused by force majeure events, including but not limited to accidents, fire, earthquake, lightning, tsunami, and war.
- Services, configurations, and gifts promised by sales personnel but not covered by the normal contract.
AV Access reserves the right to interpret these cases and make changes without notice.
11.2 Contact Information
Thank you for choosing AV Access products. If you have any questions or require technical assistance, please contact us via the following emails:
- General Enquiry: info@avaccess.com
- Customer/Technical Support: support@avaccess.com