1. Introduction
The YQCHEZI Solar Street Light S1 is a high-power, 6500K LED lighting solution designed for outdoor use, providing reliable illumination from dusk till dawn. This waterproof light is ideal for backyards, streets, and security flood lighting, operating automatically with the option for remote control adjustments.
2. Safety Warnings
- It is strictly prohibited to replace or disassemble the built-in batteries without authorization.
- Do not expose batteries to fire or high-temperature environments.
- Waste electrical products should be disposed of responsibly and recycled where appropriate facilities exist, not with household waste.
3. Package Contents
Please check the box for the following items:
- 1 x Solar Panel
- 1 x Lamp Holder (LED light fixture)
- 1 x Extension Line
- 1 x Remote Control (batteries not included)
- 1 x Pack of Expansion Screws and Assembly Hardware

Figure 3.1: Overview of included components, dimensions, and remote control. Solar panel dimensions: 27cm (10.62in) width, 18cm (7.08in) height. Lamp fixture length: 380mm (14.96in).
4. Setup and Installation
4.1 Pre-Installation Check
- Due to potential power loss during transportation, the lamp may not turn on immediately. Upon receiving, connect the lamp and solar panel correctly and place the solar panel under direct sunlight for 6-8 hours to fully charge the battery.
- Before final installation, test the lamp in an area with sufficient lighting. Confirm the indicator light is on by checking the connection to ensure normal charging.
4.2 Assembly Instructions
- Connect the lamp holder to the support arm. Carefully pass the lamp's wire through the support arm's hole.
- Attach the solar panel to its bracket using the provided screw 1 (typically two screws).
- Secure the assembled solar panel bracket to the support arm using screw 2 (typically two screws).
- Ensure all connections are secure and wires are not pinched.
Video 4.1: Step-by-step assembly and initial testing of the solar street light components.
4.3 Mounting the Light
- This product is designed for wall mounting using the provided expansion screws. Drill appropriate holes in your desired mounting location.
- Ensure the solar panel is installed in a sunny area, free from obstructions that might cast shadows.
- The orientation and tilt angle of the solar panel can be adjusted to maximize sunlight exposure throughout the day for optimal charging efficiency.

Figure 4.2: Examples of the solar street light mounted on a wall and a pole, demonstrating typical installation scenarios.
5. Operating Instructions
5.1 Automatic Operation
Once installed and charged, the lamp will operate automatically. It will turn on at dusk and turn off at dawn, requiring no manual intervention.
5.2 Remote Control Functions
The included remote control allows for manual override and timer settings:
- ON/OFF: Manually turn the light on or off at any time.
- AUTO: Press this button to enable the automatic dusk-to-dawn operation. If you wish for the lamp to stay on all night, use this setting.
- 3H / 5H / 8H: These buttons activate the timer function. After the lamp automatically turns on at night, pressing one of these buttons will set the light to turn off after 3, 5, or 8 hours respectively. The timer function has a memory, so you do not need to reset it daily.
5.3 Indicator Lights
The lamp features small indicator lights (typically red and green) on its body:
- Red Light: Generally indicates that the solar panel is connected and the battery is charging.
- Green Light: Typically indicates that the lamp is powered on or in an active operational state.
6. Maintenance
- To ensure optimal charging efficiency, it is recommended to clean any dust or debris from the surface of the solar panel every 5 months. Use a soft, damp cloth.
- Periodically check all mounting screws and connections to ensure they remain tight and secure.
7. Troubleshooting
7.1 Lamp Not Turning On
- Insufficient Charge: Ensure the solar panel has received 6-8 hours of direct sunlight. If it's the first use or after a long period of storage, a full charge is essential.
- Solar Panel Placement: Verify the solar panel is in a sunny location without obstructions.
- Connections: Check that the wire connecting the solar panel to the lamp is securely plugged in.
7.2 Light Output is Dim or Short-Lived
- Insufficient Charging: The battery may not be fully charging due to insufficient sunlight or a dirty solar panel. Clean the panel and ensure optimal placement.
- Battery Degradation: Over many years, rechargeable batteries can lose capacity. If the lamp is old, this might be a factor (though battery replacement is not user-serviceable).
8. Specifications
| Feature | Detail |
|---|---|
| Model ID | S1 |
| Brand Name | YQCHEZI |
| Light Source | LED bulbs (6500K) |
| Output Voltage | 3.2V |
| Voltage | 12 V |
| Protection Level | IP65 |
| Battery Capacity | 6000mAh |
| Battery Type | Lithium Ion Battery 26650 |
| Solar Cell Type | Lithium Battery |
| Body Material | ABS |
| Installation Method | Assembly (Wall Mount) |
| Is Dimmable | Yes |
| Is Batteries Included | Yes |
| Is Bulbs Included | No (integrated LEDs) |
| Certification | CE |
| Origin | Mainland China |
9. User Tips
- This solar street light does not include a motion sensor. It operates on a dusk-to-dawn schedule or via remote-controlled timers.
- While the provided panel mounting is functional, some users have noted that a thicker sheet metal for the mounting bracket could offer increased rigidity. Consider reinforcing if installing in high-wind areas or if extra stability is desired.
10. Warranty and Support
The product typically comes with a 2-year warranty. For any issues not covered in this manual or for warranty claims, please contact your retailer or the manufacturer directly. Keep your proof of purchase for warranty service.