1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your DESLOC C110 Smart Fingerprint Deadbolt. This advanced keyless entry system offers multiple unlocking methods including fingerprint, PIN code, and mechanical key, enhanced with a clear display for intuitive operation.

2. Specifications
| Parameter | Value |
|---|---|
| Power Supply | 4x AA Batteries (Sold Separately) |
| Working Temperature | -30°C ~ 70°C (Not Condensation) |
| Fit Door Thickness | 35mm ~ 50mm |
| Material | Aluminium Alloy |
| Unlock Mechanism | Fingerprint / Key / PIN |
| PIN Storage | 100 Groups |
| Fingerprint Storage | 50 Groups |
| Relative Humidity | <95% |
| Installation Method | Punch-free installation |
| Suitable Door Type | Steel Door, Wooden Door, Other |
| Finish Type | Painted |
| Doorknob Function | Biometric, Key & Keypad |
| Handle Direction | Direction Reversible |
| Certification | CE, FCC |
| Battery Life | 12 months |
| Waterproof Rating | IP54 |
| BHMA Grade | Grade 3 |
3. Package Contents
Ensure all components are present before beginning installation:

- a. Exterior Lock
- b. Interior Lock
- c. Mounting Plate
- d. Strike Plate
- e. Deadbolt
- f. Mechanical Key
- g. Deadbolt/Strike Plate Screws
- h. Mounting Plate Screws
- i. Interior Lock Screws
4. Installation Guide
For a visual guide, please watch the official installation video:
4.1. Functional Components Overview

4.2. Installation Steps
- Measure the Door Size:
- Ensure door thickness is 1-3/8" to 2".
- Hole diameter should be 2-1/8".
- Measured backset size of 2-3/8" or 2-3/4" with the deadbolt.
- Adjust the Length of the Deadbolt:
- Check if the deadbolt requires adjustment.
- If the backset is 70 mm, turn the faceplate 180° to extend the length.
- Install Deadbolt:
- Fix the deadbolt with 2 deadbolt screws and keep it retracted.
- Ensure the word "UP" on the deadbolt is facing up.
- Install Exterior Lock:
- Route the cable below the deadbolt.
- The paddle must be in 'horizontal' status.
- NOTE: Do not insert the key during installation. The deadbolt must be in the unlock position.
- Fix the Mounting Plate:
- Peel the tape off the mounting plate and thread the cable through the hole.
- Fix the plate with 2 mounting plate screws.
- Install the Interior Lock:
- Connect the cable securely.
- Turn the doorknob horizontally and insert the paddle.
- NOTE: Do not insert batteries until the lock is fully installed. When pressing the indoor panel against the door, conceal wires inside the door or in designated wire-housing areas.
- Fix the Interior Lock:
- Open the battery cover.
- Secure the lock with 3 interior lock screws.
- Rotate the doorknob to test if the deadbolt can be smoothly extended and retracted.
- Install Batteries:
- Place 4x AA batteries (not included) in position and close the battery cover.
5. Operating Instructions
5.1. Quick Start Guide - Button Description
- [Number button] Number and letter switching function: Press a number button once for the number, twice for 'A', three times for 'B', and four times for 'C'.
- [Enter button] Cursor move function: Press to move the cursor back or enter subsequent text. Double-click to confirm input.
- [Menu button] Backspace function: Press to backspace and delete incorrect text during input.
5.2. Change Initial PIN
- Click the [Menu button] > Enter the initial PIN "123456" > Click the [Enter button] to confirm. (The lock will automatically detect the door's opening direction. Keep the door open and avoid any operations).
- Enter the administrator's name (e.g., "Ab" by pressing [2] twice for 'A', then [Enter], then [2] three times for 'b', then double-click [Enter]).
- Enter a new PIN (6-8 digits) and press the [Enter button] to confirm.
- Enter and confirm the new PIN again, then press the [Enter button] to complete the setting.
NOTE: The initial management PIN is 123456. Add an administrator and change the administrator PIN (6-8 digits) before first use.
5.3. Fingerprint Collection
For optimal fingerprint input:
- It is recommended to use your thumb as the unlocking finger.
- Clean the fingerprint reader and your fingers, ensuring they are dry before input.
- If "Config fail" appears, re-enter the fingerprint following the on-screen instructions.
- Do not use the same finger for both administrator and user fingerprints.
5.4. User Management
Add Admin Fingerprint (FP)
- Click [Menu button] > "Add Admin" > "Add Admin FP" > "Select User".
- Select an existing administrator (e.g., "Ab") and press [Enter button].
- Place the desired finger on the Fingerprint Reader, press briefly, release, and repeat 6 times until "Config Successful" is displayed.
Add Admin PIN
- Click [Menu button] > "Add Admin" > "Add Admin PIN" > "Select User".
- Select an existing administrator (e.g., "Ab") and press [Enter button].
- Enter a new 6-8 digit PIN and press [Enter button].
- Re-enter the new PIN and press [Enter button] to confirm.
Add User Fingerprint (FP)
- Click [Menu button] > "Add User" > "Add User FP" > "Add User".
- Enter the new user's name and press [Enter button].
- Place the desired finger on the Fingerprint Reader, press briefly, release, and repeat 6 times until "Config Successful" is displayed.
Add User PIN
- Click [Menu button] > "Add User" > "Add User PIN" > "Add User".
- Enter the new user's name and press [Enter button].
- Enter a new 6-8 digit PIN and press [Enter button].
- Re-enter the new PIN and press [Enter button] to confirm.
Add Temporary PIN
- Click [Menu button] > "Add User" > "Add Temp PIN".
- Press the [Enter button] to generate 4 sets of temporary PINs. These PINs are single-use and become invalid after one use.
NOTE: Temporary PINs are displayed for 30 seconds. It is recommended to take photos for recording as the screen flashes quickly.
Delete User
- Delete Single User: Click [Menu button] > "Del User" > "Del User" > select user name (e.g., "Andy") > [Enter button].
- Delete All Users: Click [Menu button] > "Del User" > "Del All User" > "YES" > [Enter button].
- Delete Temporary PIN: Click [Menu button] > "Del User" > "Del Temp PIN" > [Enter button].
5.5. Lock Settings
Open Direction
- Click [Menu button] > "Lock Settings" > "Open Direction".
- Select "Left Open" or "Right Open" and press [Enter button] to set the door opening direction.
Passage Mode
When enabled, the door lock remains unlocked for easy access, ideal for gatherings.

- Click [Menu button] > "Lock Settings" > "Lock Setup" > "Passage Mode".
- Select ON or OFF and press [Enter button] to confirm.
NOTE: In Passage Mode, the lock will not auto-lock. Resident users can quickly enable Passage Mode by entering "5" on the keypad within 2 seconds after unlocking. To exit, set Passage Mode to "OFF" via the menu or enter "5" on the keypad within 2 seconds after unlocking.
Auto Lock
This feature automatically locks the door after a set period.
- Click [Menu button] > "Lock Settings" > "Lock Setup" > "Auto Lock".
- Press [Enter button] to select, then enter the desired auto-lock period (5-120 seconds) and press [Enter button] to confirm.
Sound Setup
Adjust the lock's sound settings.
- Click [Menu button] > "Lock Settings" > "Sound Setup" > "Sound OFF".
- Press [Enter button] to disable the sound.
Factory Reset
Resets the lock to its default factory settings.
- Method 1 (Via Menu): Click [Menu button] > "Lock Settings" > "Factory Reset" > "YES" > [Enter button].
- Method 2 (Via Reset Button): Slide up the battery cover, press and hold the Reset button, then select "YES" on the front lock and click [Enter button].
NOTE: After a factory reset, the Master PIN code reverts to 123456, and all User PINs and fingerprints are erased. Change the initial administrator PIN immediately after reset. The lock will automatically adapt to the door opening direction after battery reinstallation or initial PIN change.
6. Maintenance
- Battery Replacement: The lock uses 4x AA batteries. Replace batteries immediately when a Level 1 low battery alarm is indicated. For a Level 2 alarm, replacement is critical. In case of complete power depletion, the lock can be opened with a mechanical key or by connecting an emergency power source via the Type-C port.
- Cleaning: Regularly clean the fingerprint reader and keypad with a soft, dry cloth to ensure optimal performance. Avoid using abrasive cleaners or solvents.
- Emergency Charging: In case of low battery, connect an external mobile power supply to the Type-C backup power port for temporary power to unlock the door.

7. Troubleshooting
| Warning Icon / Event | Description / State |
|---|---|
| Failed Check Deadbolt | Indicates the lock is not properly closed or opened. Check the lock status or battery level. |
| Low Battery Replace (Level 1) | Low battery alarm. Replace batteries immediately. |
| Low Battery Inoperable (Level 2) | Critical low battery alarm. Replace batteries. The lock can be opened with a mechanical key or emergency power. |
| Passage Mode | Passage mode is currently ON. |
| Emergency Charging | When the product is not working due to low battery, an external mobile power supply can be connected for emergency use. |
| Scramble PIN | You can add arbitrary digits before and after the real PIN for a 16-digit scramble PIN function to prevent peeping. |
| Duplicate PIN | A new PIN is considered a duplicate if it contains or is contained within an existing PIN (e.g., 147258 and 14725836). |
8. User Tips
- Always keep at least one mechanical key in a safe, accessible location outside your home for emergency access.
- Regularly check battery levels, especially before extended periods away from home.
- When setting up PINs, consider using the scramble PIN feature to enhance security against shoulder surfing.
- For families or multiple users, assign unique fingerprints and PINs to each individual for better access control and tracking.
9. Warranty & Support
Your DESLOC C110 Smart Fingerprint Deadbolt comes with a 12-month warranty.
- Website: www.desloc.com
- Email Support: support@desloc.com
- Phone Support: +1 (888) 572 6136
For further detailed instructions and support, you may refer to the full user manual PDF: DESLOC C110 User Manual (PDF)