1. Product Introduction
1.1. Technical Parameters
| Parameter | Specification |
|---|---|
| Batteries | 4xAA (Sold Separately) |
| Working Temperature | -30°C ~ 70°C (Not Condensation) |
| Door Thickness | 35~50mm |
| Material | Aluminum Alloy |
| Unlock Mechanism | Key / Pin |
| Pin Groups | 100 Groups |
| Relative Humidity | <95% |
1.2. Illustration of Functional Components
The DESLOC C100 lock consists of an exterior and interior unit, each with distinct functional components.
Diagram showing the display screen, keypad, key hole, Type-C backup power port on the exterior lock, and battery cover and knob on the interior lock.
- Exterior Lock: Display Screen, Keypad, Key Hole, Type-C Backup Power Port.
- Interior Lock: Battery Cover, Knob.
2. Setup: Product Installation Instructions
For a visual guide, please watch the installation video:
Official installation video for the DESLOC C100 Keyless Entry Door Lock.
2.1. What's Included for Installation
Ensure all components are present before beginning installation:
Visual representation of the exterior lock, interior lock, mounting plate, strike plate, deadbolt, mechanical keys, and various screws.
- Exterior Lock
- Interior Lock
- Mounting Plate
- Strike Plate
- Deadbolt
- Mechanical Key
- Deadbolt/Strike Plate Screws
- Mounting Plate Screws
- Interior Lock Screws
2.2. Installation Steps
Follow these steps carefully for proper installation:
The DESLOC C100 lock, showing the keypad and display.
-
Measure the Door Size
Ensure your door meets the following specifications:
- Door thickness: 1-3/8" to 2" (35mm to 50mm)
- Hole diameter: 2-1/8" (54mm)
- Backset size: 2-3/8" or 2-3/4" (60mm or 70mm)
Diagram illustrating door thickness, hole diameter, and backset measurements for compatibility.
-
Adjust the Length of the Deadbolt
Check if the deadbolt requires adjustment. If the backset is 70mm, turn the faceplate 180° to extend the length.
-
Install Deadbolt
Fix the deadbolt with 2 deadbolt screws and keep it retracted. Ensure the word "UP" on the deadbolt is facing up.
-
Install Exterior Lock
Route the cable below the deadbolt. The paddle must be in a 'horizontal' status. Note: Do not insert the key during installation. The deadbolt must be in the unlock position, and the paddle must be in 'horizontal' status.
-
Fix the Mounting Plate
Peel the tape off the mounting plate and thread the cable through the hole. Fix the plate with 2 mounting plate screws.
-
Install the Interior Lock
Connect the cable securely. Turn the doorknob horizontally and insert the paddle. Note: Do not insert batteries until the lock is fully installed. When pressing the indoor panel against the door, conceal wires inside the door or in designated wire-housing areas.
-
Fix the Interior Lock
Open the battery cover. Secure the lock with 3 interior lock screws. Rotate the doorknob to test if the deadbolt extends and retracts smoothly.
-
Install Batteries
Place the 4xAA batteries (sold separately) in position and close the battery cover.
3. Operating Instructions
3.1. Product Button Description
Understand the functions of the keypad buttons:
- Number buttons (0-9): Used to enter PINs, numbers, and names. Also function as letter switches (e.g., press '2' once for '2', twice for 'A', three times for 'B', four times for 'C').
- [Menu] button: Enters the settings interface, returns to the previous menu, and acts as a backspace to delete incorrect input.
- [Enter] button (Lock icon): Confirms current operations. Double-click to confirm after input is complete. Press to lock the door.
- [Up arrow] button: Scrolls menu items up.
- [Down arrow] button: Scrolls menu items down.
The lock's display showing 'Config Successful' after an operation, demonstrating visualized feedback.
3.2. Changing Initial PIN
The initial management PIN is 123456. It is crucial to change this immediately after installation.
- Press the [Menu] button.
- Enter the initial PIN "123456" and press the [Enter] button to confirm. (The lock will automatically detect the door's opening direction. Keep the door open during this step.)
- Enter the administrator's name (e.g., "Ab" by pressing '2' twice for 'A', then [Enter], then '2' three times for 'b', then double-click [Enter]).
- Enter a new 6-8 digit PIN and press the [Enter] button to confirm.
- Re-enter the new PIN to confirm and press the [Enter] button. The new PIN setting is now complete.
NOTE: After changing the initial PIN, the lock will automatically adapt to the door opening direction.
3.3. Adding Admin PIN
You can add new administrator PINs or assign a PIN to an existing administrator.
a. Add PIN code for an existing administrator:
- Press the [Menu] button > select "Add Admin" > "Add Admin PIN" > "Select User".
- Select an existing administrator (e.g., "Ab") and press the [Enter] button to confirm.
- Enter a new 6-8 digit PIN and press the [Enter] button to confirm.
- Re-enter the new PIN to confirm and press the [Enter] button.
b. Add PIN code for a new administrator:
- Press the [Menu] button > select "Add Admin" > "Add Admin PIN" > "Add User".
- Enter the name of the new administrator and press the [Enter] button to confirm.
- Enter a new 6-8 digit PIN and press the [Enter] button to confirm.
- Re-enter the new PIN to confirm and press the [Enter] button.
3.4. Adding User PIN
You can add new user PINs or assign a PIN to an existing user.
a. Add PIN code for a new user:
- Press the [Menu] button > select "Add User" > "Add User PIN" > "Add User".
- Enter the name of the new user and press the [Enter] button to confirm.
- Enter a new 6-8 digit PIN and press the [Enter] button to confirm.
- Re-enter the new PIN to confirm and press the [Enter] button.
b. Add PIN code for an existing user:
- Press the [Menu] button > select "Add User" > "Add User PIN" > "Select User".
- Select an existing user (e.g., "Andy") and press the [Enter] button to confirm.
- Enter a new 6-8 digit PIN and press the [Enter] button to confirm.
- Re-enter the new PIN to confirm and press the [Enter] button.
3.5. Adding Temporary PIN
Temporary PINs are single-use and become invalid after one use.
- Press the [Menu] button > select "Add User" > "Add Temp PIN".
- Press the [Enter] button to confirm. The lock will generate 4 sets of temporary PINs.
NOTE: The temporary PINs are displayed for only 30 seconds. It is recommended to take a photo with your mobile phone for recording, or take multiple photos as the screen flashes quickly.
3.6. Deleting Users and Temporary PINs
a. User Info (Query User Count and Unlock Modes):
- User Count: Press the [Menu] button > select "Del User" > "User Info" > "User Count" to view the number of registered users.
- Key: Press the [Menu] button > select "Del User" > "User Info" > "Key" to view the number of regular and temporary PINs.
b. Delete a single user:
Administrators and ordinary users can be deleted, but the primary administrator cannot.
- Press the [Menu] button > select "Del User" > "Del User".
- Select the user name to be deleted (e.g., "Andy") and press the [Enter] button to delete all user information.
c. Delete all regular users:
- Press the [Menu] button > select "Del User" > "Del All User" > "YES".
- Press the [Enter] button to delete all users' information.
d. Delete Temporary PINs:
- Press the [Menu] button > select "Del User" > "Del Temp PIN".
- Press the [Enter] button to delete the temporary PINs.
NOTE: If a temporary PIN has been issued but not used, and you do not wish for it to be used by others, you can delete all 4 sets of temporary PINs or regenerate new ones.
3.7. Lock Settings
a. Open Direction:
To set the door opening direction:
- Press the [Menu] button > select "Lock Settings" > "Open Direction".
- Select "Left Open" or "Right Open" and press the [Enter] button.
b. Passage Mode:
When enabled, the door lock will remain unlocked, allowing free passage.
The lock's display showing 'Passage mode' when activated.
- Press the [Menu] button > select "Lock Settings" > "Lock Setup" > "Passage Mode".
- Select "ON" or "OFF" as required and press the [Enter] button to confirm.
Quick Enable: After unlocking with fingerprint or PIN, resident users can enter "5" through the keypad within 2 seconds to enable Passage Mode. The screen will display "Passage Mode" when active and in sleep state.
Exit Method: Users can enter the [Menu] button and set "Passage Mode" to "OFF", or enter "5" through the keypad within 2 seconds after unlocking with fingerprint or PIN.
c. Auto Lock:
Sets the time period after which the lock automatically closes.
- Press the [Menu] button > select "Lock Settings" > "Lock Setup" > "Auto Lock".
- Press the [Enter] button to select, then enter the desired auto-lock period (5-120 seconds) and press the [Enter] button to confirm.
d. Sound Setup:
To turn the lock's sound ON or OFF.
- Press the [Menu] button > select "Lock Settings" > "Sound Setup" > "Sound OFF".
- Press the [Enter] button to select Sound OFF.
e. Factory Reset:
A factory reset restores the lock to its default settings, reverting the Master PIN to 123456 and erasing all user PINs and fingerprints.
Method 1 (Via Menu):
- Press the [Menu] button > select "Lock Settings" > "Factory Reset" > "YES".
- Press the [Enter] button to confirm.
Method 2 (Via Reset Button):
- Slide up the battery cover on the interior lock.
- Press and hold the Reset button.
- On the front lock, select "YES" for "Factory Reset?" and press the [Enter] button to confirm.
NOTE: After a factory reset, immediately change the initial administrator PIN. If the battery is reinstalled or the initial PIN is changed after a factory reset, the lock will automatically adapt to the door opening direction.
4. Maintenance
4.1. Battery Life and Replacement
The DESLOC C100 is designed for approximately 1 year of battery life with typical usage. When the battery level is low, the lock will provide warnings.
- Level 1 Low Battery Alarm: Replace batteries immediately when you receive this alert.
- Level 2 Low Battery Alarm (Inoperable): This indicates critical battery levels. Replace batteries urgently. If power runs out completely, the lock can be opened using the mechanical key or by connecting an emergency power source via the Type-C port.
Illustration of the lock's PowerMax features, highlighting 1-year battery life and emergency charging capability.
4.2. Emergency Power
If the batteries are completely drained and the lock is unresponsive, connect an external mobile power supply to the Type-C backup power port for emergency use to unlock the door.
5. Troubleshooting
5.1. Warning Icons and Their Meanings
| Warning Icon | State Description |
|---|---|
| Failed Check Deadbolt | Indicates that the lock is not properly closed or opened. Check the lock status or battery level. |
| Low Battery Replace | Level 1 low battery alarm. Replace the battery immediately. |
| Low Battery Inoperable | Level 2 low battery alarm; replace batteries. The lock can be opened with a mechanical key or emergency power. |
| Passage Mode | Passage mode is currently ON. |
5.2. Function Description Notes
- Scramble PIN: You can add arbitrary digits before and after your real PIN (up to 16 digits total) to prevent others from guessing your code.
- Duplicate PIN: Be aware that if a new PIN contains or is included within an existing PIN (e.g., 147258 and 14725836), it will be considered a duplicate.
6. User Tips
- Initial Setup Security: Always change the default Master PIN (123456) immediately after installation to enhance security.
- Temporary PIN Management: If you generate temporary PINs but they are not used or you no longer wish for them to be active, delete them promptly to maintain control over access.
- Cable Management: During installation of the interior lock, take care to neatly conceal all wires within the door or designated housing areas to prevent damage and ensure a clean aesthetic.
- Door Opening Direction: The lock automatically adapts to the door's opening direction after initial setup or a factory reset, but ensure the door is open and free of obstructions during this process.
7. Warranty & Support
For further assistance or warranty claims, please contact DESLOC support:
- Website: www.desloc.com
- Email: support@desloc.com
- Phone: +1 (888) 572 6136
- Warranty: 12-month warranty