RACBOX Motorcycle Turn Signal Lights

Contents

RACBOX Motorcycle Turn Signal Lights Instruction Manual

Model: Universal Fit Motorcycle Turn Signal Lights

1. Introduction

Thank you for choosing RACBOX Motorcycle Turn Signal Lights. This manual provides essential information for the safe and effective installation, operation, and maintenance of your new turn signal lights. Please read this manual thoroughly before installation and keep it for future reference.

Four amber motorcycle turn signal lights in the foreground, with a motorcycle's rear showing installed lights in the background.

Figure 1: RACBOX Motorcycle Turn Signal Lights (4-piece set)

2. Product Overview

These turn signal lights are designed as direct replacement parts for a wide range of motorcycles, including Honda, Yamaha, Suzuki, Kawasaki, and various Cafe Racer models. They feature an amber lens and light color, providing clear signaling for enhanced road safety.

Collage showing the turn signal lights installed on different motorcycles, both front and rear.

Figure 2: Turn Signal Lights installed on various motorcycles

3. Setup and Installation

3.1 Before You Begin

  • Ensure your motorcycle's ignition is turned off and the battery is disconnected to prevent electrical shorts.
  • Gather necessary tools: Wrench (for 10mm bolt), wire strippers, crimpers, electrical tape or heat shrink tubing.
  • Verify the mounting location on your motorcycle is suitable for a 10mm screw diameter.

3.2 Installation Steps

  1. Remove Old Lights: Carefully disconnect the wiring and unbolt your existing turn signal lights.
  2. Mount New Lights: Insert the 10mm screw of the new turn signal light into the mounting hole. Secure it firmly with a wrench, ensuring the light is oriented correctly.
  3. Wire Connection: These lights feature a 2-wire connection. Typically, one wire is for positive (+) and the other for negative (-) (ground).
    • Connect the positive wire from the turn signal light to your motorcycle's corresponding turn signal wire.
    • Connect the negative wire from the turn signal light to a suitable ground point on your motorcycle's frame or the motorcycle's ground wire.
    • Ensure all connections are secure and insulated with electrical tape or heat shrink tubing to prevent corrosion and short circuits.
  4. Test Functionality: Reconnect your motorcycle's battery. Turn on the ignition and test each turn signal to ensure they illuminate correctly and flash at the appropriate rate.
Text on a white background: 'Directly Replacement Parts.'

Figure 3: Designed as direct replacement parts

4. Operating Instructions

These turn signal lights operate in conjunction with your motorcycle's existing turn signal switch. When the turn signal switch is activated (left or right), the corresponding amber light will illuminate and flash, indicating your intended direction to other road users.

5. Maintenance

  • Cleaning: To maintain optimal visibility and appearance, clean the lens and body of the turn signal lights regularly with a soft, damp cloth. Avoid abrasive cleaners that could scratch the plastic.
  • Inspection: Periodically check the wiring connections for any signs of wear, corrosion, or looseness. Ensure the mounting bolt remains tight.
  • Bulb Replacement: These units use ordinary bulbs. If a bulb fails, it may be replaceable by carefully disassembling the light housing. Refer to the specifications for bulb type if replacement is needed.

6. Troubleshooting

6.1 Light Not Working

  • Check Connections: Ensure all wires are securely connected and properly insulated.
  • Check Ground: Verify that the ground connection is solid and free from corrosion.
  • Check Bulb: The bulb may be burnt out. If possible, test the bulb or replace it.
  • Check Motorcycle's Fuse: A blown fuse in your motorcycle's electrical system can prevent the lights from working.

6.2 Light Flickers or is Dim

  • Loose Connection: Inspect all wiring connections for looseness.
  • Poor Ground: Ensure a clean and secure ground connection.
  • Low Voltage: Check your motorcycle's battery voltage.

7. Specifications

Dimensional drawing of the turn signal light showing front and side views with measurements in millimeters.

Figure 4: Product Dimensions

FeatureSpecification
Item TypeMotorcycle Turn Signal Light
MaterialPlastic
Lens ColorAmber
Body ColorSilver / Black (SKU dependent)
Light ColorAmber
Bulb TypeOrdinary Bulb
Quantity4 Pieces (2 pairs)
Connection2 Wires
VoltageDC 12V
Screw Diameter10mm
Light Diameter45mm
Total Height104mm
Light Depth60mm
Stem Length59mm (from base of light to start of thread)
Thread Length26mm
FitmentUniversal for most motorcycles (Honda, Yamaha, Suzuki, Kawasaki, Cafe Racer, etc.)

8. User Tips

  • Always ensure wiring is correctly connected (positive to positive, negative to ground) to prevent damage to the lights or your motorcycle's electrical system.
  • Regularly check the tightness of the mounting bolts, especially after riding on rough terrain, to prevent lights from vibrating loose.
  • Consult your local vehicle regulations regarding turn signal light requirements and placement.

9. Warranty and Support

For warranty information, please refer to the terms provided by your retailer or contact RACBOX directly. Keep your proof of purchase for any warranty claims.

For further assistance or technical support, please contact the seller or manufacturer.

A detailed user manual in PDF format may also be available at: User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.