ShangDeLi Car LED Radar Front Rear Fog Light Power On Off Switch Button

Contents

Instruction Manual

ShangDeLi Car LED Radar Front Rear Fog Light Power On Off Switch Button

Model: Car LED Radar Front Rear Fog Light Power On Off Switch Button

1. Product Overview

This manual provides instructions for the installation, operation, and maintenance of the ShangDeLi Car LED Radar Front Rear Fog Light Power On Off Switch Button. This product is designed as a modification accessory for vehicles, specifically compatible with Ford Focus 2 Mk2 models from 2009 to 2011.

Product Name: Car Switch
Batch/Serial Number: Button Switch

2. Safety Instructions (WARNING!)

  • Disconnect the negative terminal of the car battery before installation to cut off power and avoid short circuits or electric shock. Do not operate with power on to avoid short circuit, sparks, or damage to the vehicle circuit.
  • This product is only suitable for 12V DC vehicle power supply. DO NOT connect to 220V AC household power, otherwise it may cause burning, fire, or electric shock.
  • The switch has a rated current limit. High-power devices (lights, air pumps, light bars, etc.) must be used with a relay. Do not directly drive heavy loads to avoid overheating and burning the switch.
  • All wiring must be firm and well-insulated. Use heat-shrink tubing or electrical tape to cover all connectors. Exposed metal is strictly prohibited to prevent short circuit and fire.
  • Ensure the waterproof gasket is correctly installed and compressed during installation. Keep the switch away from high temperature, oil, and water areas for good waterproofing and heat dissipation.
  • Do not disassemble or modify the internal structure of the switch by yourself, so as not to lose waterproof and insulation performance and cause failure or danger.
  • Non-professionals should install under the guidance of automotive electricians. Wrong wiring may cause damage to vehicle electrical appliances, malfunctions, or even safety hazards.
  • If the switch becomes loose, hot, smelly, noisy, or abnormal, stop using it immediately and check or replace it.
  • This product is a car modification accessory. Installation and use must comply with local traffic laws and vehicle safety standards.

3. Specifications

Feature Specification
Input Voltage DC 12V
Rated Current 1.5A
Rated Power 18W (Max)
Material Flame-retardant ABS (PC+ABS)
Working Temperature -10°C ~ 60°C
Dimensions (L*W*H) 4cm * 3.6cm * 2.8cm
Backlight Color Upper working indicator: Orange; Lower icon light: Blue
Switch Type Latching (fixed switch, doesn't return after press, stays in pressed position)

4. Package Contents

  • 1 x Car Switch
  • 1 x Connector with cable

5. Installation & Wiring

5.1. Preparation

Before beginning, disconnect the negative terminal of the car battery to prevent electrical hazards. Gather necessary tools such as a screwdriver, wire stripper, heat-shrink tubing or electrical tape, and a hole punch if drilling is required. Verify that all components are included in the package.

5.2. Drilling & Installation

This switch is designed to replace a blank reserved switch directly. Insert the switch from the front of the panel. Install the waterproof gasket, ensuring it is properly seated without deviation. Then, install the washer and mounting nut on the back of the panel. Tighten moderately with a screwdriver to ensure the switch is stable and the gasket is fully compressed. If drilling is necessary, select a suitable position and drill accurately to match the switch dimensions (approximately 2.8cm x 3.6cm on the face, 4cm depth).

Dimensions of the car switch, showing a width of 3.6cm, depth of 4cm, and height of 2.8cm.

Figure 1: Switch Dimensions (Width: 3.6cm, Depth: 4cm, Height: 2.8cm)

5.3. Wiring

This is an on-off switch without voltage conversion. The input voltage is the same as the output voltage (12V-24V DC). Distinguish positive and negative poles to avoid reverse connection. Refer to the wiring diagram below for detailed steps. After connecting, wrap all connectors with heat-shrink tubing or electrical tape to prevent exposed metal and short circuits.

Wiring diagram for the car switch. Yellow wire is positive input, Black wire (2) is backlight negative, Black wire (5) is indicator negative, Blue wire is positive output/positive indicator, Red wire is icon backlight positive.

Figure 2: Wiring Diagram

  • 1# Yellow wire: positive input wire
  • 2# Black Wire: backlight negative wire
  • 5# Black Wire: indicator negative wire
  • 6# Blue Wire: positive output wire / positive indicator wire
  • 7# Red wire: Icon backlight positive wire

6. Operation

6.1. Power-on Test

After completing the wiring, carefully check that all connections are firm, no wires are exposed, and there is no reverse polarity. Reconnect the negative terminal of the car battery. Toggle the switch to test whether the LED indicator and the connected electrical device work normally. Observe for any signs of overheating, abnormal noise, or other irregularities.

Image showing the switch in 'Turn On' state with an orange LED and 'Turn Off' state with the LED off.

Figure 3: LED Indicator States (Turn On / Turn Off)

The switch features a latching mechanism: press once to turn it on (it stays in the pressed position), and press again to switch it off.

6.2. Finishing

Once the power-on test is successful, organize the wires and secure any excess harness with cable ties to prevent winding and wear. Apply function labels for easy identification. Double-check that the switch is securely installed and the waterproof gasket is properly sealed.

7. Maintenance

To ensure the longevity and proper functioning of your switch, follow these general maintenance guidelines:

  • Regularly inspect the switch and its wiring for any signs of wear, damage, or loose connections.
  • Keep the switch clean. Use a soft, dry cloth to wipe away dust or debris. Avoid using harsh chemicals or abrasive cleaners.
  • Ensure the area around the switch remains free from excessive moisture, oil, or extreme temperatures to maintain its waterproof and heat dissipation properties.

8. Troubleshooting

If you encounter any issues with the switch, consider the following:

  • Switch not responding or LED not lighting up: Check all wiring connections for firmness and correct polarity. Ensure the car battery is properly connected and providing 12V DC power.
  • Overheating, abnormal noise, or smell: Immediately disconnect power. This could indicate a short circuit or an overloaded circuit. Verify that high-power devices are connected via a relay and that the switch's rated current is not exceeded. Inspect wiring for exposed metal.
  • Loose switch: Re-tighten the mounting nut and ensure the waterproof gasket is correctly compressed.
  • Intermittent operation: Check for loose wires or damaged insulation.

If problems persist or you are unsure about any step, consult a qualified automotive electrician.

9. User Tips

  • This switch features a latching mechanism, meaning it stays in the 'on' or 'off' position after being pressed. Ensure this functionality is suitable for your intended application.
  • Users have confirmed this switch fits Ford Focus models around 2010. Always verify compatibility with your specific vehicle model and year before installation.
  • The button is noted for its gentle press and good build quality.

10. Compliance Information

  • CE Marking: This product complies with EU safety standards (LVD – Low Voltage Directive, EMC – Electromagnetic Compatibility Directive, RoHS – Restriction of Hazardous Substances Directive).
  • RoHS Compliance: The product is free of lead, mercury, cadmium, hexavalent chromium, and other hazardous substances, meeting environmental protection standards.

11. Support & Documentation

For additional information or detailed diagrams, please refer to the official user manual PDF available online. A comprehensive PDF document with further details can be accessed at: User Manual (PDF).

For technical support or inquiries, please contact your retailer or the manufacturer directly.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.