1. Introduction
This manual provides instructions for the installation, maintenance, and troubleshooting of the Engine Oil Radiator Cooler. This component is a critical part of the engine cooling system for vehicles equipped with the EA888 engine family (Generation 2 and 3). It functions by transferring excess heat from the engine oil to the engine coolant, ensuring the oil remains within the optimal temperature range for lubrication and performance. This unit is designed to meet or exceed OEM specifications for Volkswagen and Audi.
2. Compatibility & Fitment
This Oil Cooler is designed for VW and Audi models equipped with 1.8 TSI and 2.0 TFSI (EA888) engines.
Important Note: This cooler fits EA888 Gen 2 and Gen 3 engines. Please verify your original part number (e.g., 06J117021J or 06L117021E) to ensure compatibility.
Compatible Volkswagen Models:
- Golf MK6, MK7, MK7.5 (including GTI & R)
- Jetta (GLI)
- Passat (B7, B8)
- Tiguan (MK1, MK2)
- Beetle (Turbo)
- Scirocco
- CARAVELLE V Bus 2.0 TSI (05.2011 - 08.2015)
- CARAVELLE V Bus 2.0 TSI 4motion (07.2011 - 08.2015)
- CC (358) 1.8 TSI (11.2011 - 12.2016)
- EOS (1F7, 1F8) 2.0 TFSI (03.2006 - 08.2015)
- MAGOTAN Variant (365) 2.0 TSI (11.2010 - 12.2015)
- MULTIVAN V (7HM, 7HN, 7HF, 7EF, 7EM, 7EN) 2.0 TSI (05.2011 - 08.2015)
- MULTIVAN V (7HM, 7HN, 7HF, 7EF, 7EM, 7EN) 2.0 TSI 4motion (07.2011 - 08.2015)
- MULTIVAN VI (SGF, SGM, SGN, SHM, SHN) 2.0 TSI 4motion (06.2015 - )
- PASSAT / Magotan (3C2) 1.8 TSI (05.2007 - 07.2010)
- PASSAT / Magotan (3C2) 2.0 FSI (07.2005 - 07.2010)
- PASSAT ALLTRACK (365) 2.0 TSI 4motion (01.2012 - 12.2014)
- PASSAT CC (357) 2.0 TSI (06.2008 - 01.2012)
- SHARAN (7N1, 7N2) 1.8 TSI (11.2011 - )
- SHARAN (7N1, 7N2) 2.0 TSI (12.2010 - )
- TIGUAN (5N_) 2.0 TFSI 4motion (09.2007 - 07.2018)
- TRANSPORTER / CARAVELLE VI Bus (SGB, SGG, SGJ, SGC, SHB, SHJ) 2.0 TSI (04.2015 - )
- TRANSPORTER / CARAVELLE VI Bus (SGB, SGG, SGJ, SGC, SHB, SHJ) 2.0 TSI 4motion (06.2015 - )
Compatible Audi Models:
- A3 (8P, 8V)
- A4 (B8, B9)
- A5 (8T, F5)
- A6 (C7)
- A7
- Q5
- A3 (8P1) 1.8 TFSI (11.2006 - 08.2012)
- A3 (8P1) 2.0 TFSI (09.2004 - 08.2012)
- A3 Convertible (8P7) 1.8 TFSI (04.2008 - 05.2013)
- A3 Sportback (8PA) 1.8 TFSI (11.2006 - 03.2013)
- A4 (8K2, B8) 1.8 TFSI (01.2008 - 12.2015)
- A4 (8K2, B8) 2.0 TFSI (06.2008 - 12.2015)
- A4 Allroad (8KH, B8) 2.0 TFSI quattro (04.2009 - 05.2016)
- A4 Avant (8K5, B8) 2.0 TFSI (06.2008 - 12.2015)
- A5 (8T3) 1.8 TFSI (10.2007 - 01.2017)
- A5 (8T3) 2.0 TFSI (11.2008 - 03.2012)
- A5 Convertible (8F7) 2.0 TFSI (03.2009 - 03.2012)
- A5 Sportback (8TA) 2.0 TFSI (09.2009 - 06.2014)
- A6 (4G2, 4GC, C7) 2.0 TFSI hybrid (11.2011 - 09.2018)
- A8 (4H2, 4H8, 4HC, 4HL) 2.0 TFSI hybrid (02.2012 - 11.2015)
- Q3 (8UB, 8UG) 2.0 TFSI quattro (06.2011 - 04.2015)
- Q5 (8RB) 2.0 40 Hybrid quattro (09.2012 - 05.2016)
- Q5 (8RB) 2.0 TFSI quattro (08.2009 - 05.2017)
- TT (8J3) 1.8 TFSI (06.2008 - 06.2014)
- TT (8J3) 2.0 45 TFSI (05.2010 - 06.2014)
- TT Roadster (8J9) 1.8 TFSI (06.2008 - 06.2014)
- TT Roadster (8J9) 2.0 TFSI (03.2007 - 06.2010)
Compatible Skoda Models:
- OCTAVIA II Combi (1Z5) 1.8 TSI (06.2007 - 04.2013)
- SUPERB II (3T4) 1.8 TSI (03.2009 - 05.2015)
- SUPERB II (3T4) 1.8 TSI 4x4 (03.2009 - 05.2015)
- SUPERB II (3T4) 2.0 TSI (05.2010 - 05.2015)
- SUPERB II Estate (3T5) 2.0 TSI (05.2010 - 05.2015)
- YETI (5L) 1.8 TSI 4x4 (11.2009 - 12.2017)
Compatible Seat Models:
- ALHAMBRA (710, 711) 1.8 TSI (11.2012 - )
- ALHAMBRA (710, 711) 2.0 TSI (11.2010 - )
- LEON (1P1) 1.8 TSI (06.2007 - 12.2012)
- LEON (1P1) 2.0 TFSI (06.2009 - 12.2012)
3. Technical Specifications
| Feature | Details |
|---|---|
| Product Name | Engine Oil Cooler / Radiator |
| OEM Part Numbers | 06J117021J, 06L117021E |
| Material | Aluminum (High Thermal Conductivity) |
| Engine Fitment | EA888 (1.8 TSI / 2.0 TFSI) |
| Function | Heat exchange to regulate engine oil temperature. |
| High-concerned chemical | None |
| Origin | Mainland China |
4. Common Symptoms of Failure
If your original oil cooler is failing or leaking, you may experience the following issues:
- Oil in Coolant: Milky sludge in the coolant expansion tank (indicates internal seal failure).
- Oil Leaks: Visible oil leaking from the cooler housing or gasket area.
- Overheating: Engine oil temperature consistently exceeding 110° C - 120° C during normal driving.
- Low Oil Pressure: Warning light on the dashboard due to pressure loss.
5. Installation Instructions
Warning: Installation should only be performed by qualified automotive technicians. Improper installation can lead to severe engine damage.
Step 1: Preparation
- Park the vehicle on a level surface and allow the engine to cool completely.
- Disconnect the negative (-) battery terminal.
- Drain the engine coolant into a suitable container.
- (Recommended) Drain the engine oil.
Step 2: Removal of Old Unit
- Remove the engine cover to access the oil cooler assembly (located near the oil filter housing).
- Disconnect the coolant hoses connected to the oil cooler. Be prepared for coolant spillage.
- Remove the oil filter housing cap and the oil filter.
- Unbolt the oil cooler from the engine block.
- Carefully remove the cooler and discard the old O-rings and gaskets.
Step 3: Cleaning
- Thoroughly clean the mating surface on the engine block where the cooler sits. Ensure no old gasket material or debris remains.
- If the old cooler leaked oil into the water, the cooling system must be flushed thoroughly.
Step 4: Installation of New Unit
- Install new O-rings and gaskets onto the new oil cooler. Do not reuse old seals.
- Position the new oil cooler onto the engine block.
- Tighten the mounting bolts to the manufacturer's specified torque.
- Reconnect the coolant hoses and ensure clamps are secure.
- Install a new oil filter and reinstall the filter housing cap.
Step 5: Refill & Test
- Refill the engine with the correct specification of oil (e.g., VW 502 00 / 504 00).
- Refill the cooling system with the appropriate coolant mixture (G12/G13).
- Reconnect the battery.
- Start the engine and let it idle. Check carefully for any oil or coolant leaks.
- Bleed the cooling system to remove air pockets.
Product Overview Video
Video showcasing the Engine Oil Radiator Cooler from various angles.
Product Images
6. Maintenance & Tips
- Coolant Flush: If the old cooler failed internally (oil in coolant), simply draining the radiator is not enough. The entire cooling system (including the heater core) must be flushed to prevent contamination.
- Seals: Always use the new seals provided with the unit. Reusing old rubber seals is the most common cause of post-installation leaks.
- Oil Change: Perform an oil change shortly after installation to ensure no contaminants remain in the lubrication system.
7. Troubleshooting
If you encounter issues after installation, review the common symptoms of failure (Section 4) and consider the following:
- Persistent Leaks: Recheck all connections, hose clamps, and ensure new gaskets/O-rings were properly installed and tightened to specified torque.
- Continued Overheating: Verify proper coolant levels and ensure the cooling system has been thoroughly bled of air pockets. Check for proper oil levels and correct oil specification.
- Warning Lights: If a low oil pressure warning persists, consult a qualified technician immediately.
8. User Tips
- Always verify compatibility with your vehicle's VIN or original part number before installation to ensure correct fitment.
- Consider replacing related components like hoses or clamps if they show signs of wear during the installation process.
9. Warranty & Support
This product is covered under a 12-month warranty against manufacturing defects.
Warranty Void If:
- Damaged by improper installation.
- Overheating due to lack of coolant.
- Use of incorrect fluids.
For detailed torque specifications and safety procedures, always refer to the official Volkswagen/Audi Workshop Manual (WIS). A PDF version of this user manual is available for download: Download User Manual (PDF).