FGHGF FS2A 4CH AFHDS 2A Mini Compatible Receiver

Contents

FS2A 4CH AFHDS 2A Mini Compatible Receiver User Manual

Model: FS2A 4CH AFHDS 2A Mini Compatible Receiver

1. Introduction

This manual provides detailed instructions for the FGHGF FS2A 4CH AFHDS 2A Mini Compatible Receiver. This receiver is designed to be compatible with Flysky I6, I6X, and I6S Transmitters, offering PWM output for various RC applications. Please read this manual thoroughly before use to ensure proper operation and safety.

Front view of the FS2A 4CH AFHDS 2A Mini Compatible Receiver
Front view of the FS2A 4CH AFHDS 2A Mini Compatible Receiver.

2. Safety Warnings

  • This product is intended for adult use only.
  • Keep out of reach of children and pets to prevent accidental injury or ingestion.
  • Always check that the installation is correct before operating.
  • If you observe abnormal noise or equipment error after installation, immediately stop using the device.
  • Follow all instructions for proper use. Misuse may cause harm.
  • Store the product in a dry and shady place, away from high temperatures, humidity, and direct sunlight.

3. Product Overview

The FS2A 4CH AFHDS 2A Mini Compatible Receiver is a compact and lightweight component for your RC models. It features a PCB board with an integrated antenna and connection pins for PWM output.

Angled view of the FS2A 4CH AFHDS 2A Mini Compatible Receiver with pin headers
Angled view of the receiver, showing the main board and included pin headers.
Dimensions of the FS2A 4CH AFHDS 2A Mini Compatible Receiver
The receiver measures approximately 11mm in width and 25mm in length.

4. Setup Instructions

4.1. Binding the Receiver

To establish a connection between your receiver and transmitter, follow these steps:

  1. Press and hold the bind key on the receiver. While holding the key, connect power to the receiver. The blue light on the receiver will begin flashing, indicating it has entered binding mode.
  2. Set your compatible Flysky transmitter (I6, I6X, or I6S) into bind mode. Ensure the transmitter is configured for the AFHDS 2A protocol. Once the transmitter enters bind mode, the receiver's blue light will change from rapid flashing to a slow flash.
  3. Exit bind mode on your transmitter. The receiver's blue light should then become solid bright, indicating that the signal has been successfully received and binding is complete.

4.2. Failsafe Settings

Failsafe ensures that your model behaves predictably in case of signal loss. To set up failsafe:

  1. Ensure the receiver is normally receiving the transmitter signal (blue light solid).
  2. Position the control rockers on your transmitter to the desired failsafe settings (e.g., throttle to zero, control surfaces neutral).
  3. Long press the receiver's bind button. The blue light will flash quickly several times and then remain solid bright. This indicates that the failsafe settings have been successfully saved.
Wiring diagram for the FS2A 4CH AFHDS 2A Mini Compatible Receiver
Wiring diagram showing PWM outputs (CH1-CH4), VCC, GND, and input voltage range (IN: 3.3-10V).

5. Specifications

Feature Specification
Model FS2A 4CH AFHDS 2A Mini Compatible Receiver
Channels 4
Output PWM
Compatibility Flysky I6, I6X, I6S Transmitters (AFHDS 2A protocol)
Input Voltage 3.3-10V
Dimensions (L x W x H) 25mm x 11mm x 3mm
Color Black
Material PCB

6. User Tips

  • Before first use, always inspect the product for any signs of damage.
  • After each use, store the receiver in a dry place and ensure it is kept away from children.

7. Troubleshooting

  • If you encounter abnormal noise or equipment errors after installation, immediately power off the device and re-check all connections and settings.
  • If binding fails, ensure your transmitter is set to the correct AFHDS 2A protocol and that the receiver is properly powered during the binding process.

8. Warranty and Support

For further assistance or inquiries, please contact the manufacturer or authorized representative:

  • Manufacturer: Taiyuan nitaiteng trading co., ltd
  • Address: Room 603B, Unit 3, Building 1, No.100 Yingze West Street, Wanbailin District, Taiyuan City, Shanxi Province, Code: 030000
  • Contact: bhdmxiyypq@163.com / +8618825272353
  • EU Authorized Representative: CET PRODUCT SERVICE LTD.
  • Address: Osterholzallee 144
  • Contact: info@cetproduct.com / +49 15738616277

An additional user manual in PDF format is available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.