TiESFONG A99

Contents

TiESFONG A99 4-Channel FHD 1080P Car Dash Cam User Manual

Model: A99 | Brand: TiESFONG

1. Introduction and Safety Reminders

Please read this instruction carefully and completely before using the product!

1.1 About Security

  1. Please read this 'User Manual' carefully before using the dash cam. It contains important information for your safety as well as operating and maintenance instructions.
  2. Follow all safety precautions to prevent damage due to improper use of the dash cam.
  3. Avoid extended exposure of the dash cam to direct sunlight or extreme temperatures (either extreme high or low temperature) which tend to degrade or damage the unit and its normal functionality.
  4. Do not try to open the cover or repair it yourself. If the accessories for this device have any problem, please contact the seller for assistance.
  5. Use the dash cam unit only for its intended purpose. Do not use it in a way that would be illegal or that tends to physically damage the unit, or cause danger to the safe operation of the vehicle or its occupants.
  6. Do not operate or install the dash cam while driving, or attempt to change any settings.
  7. Do not connect the uninterruptible power supply without authorization, as it may cause car or product failure. Please consult a professional for installation matters.
  8. When cleaning or repairing the car, stop using or remove the dash cam.
  9. Do not install this dash cam in a place that would obstruct or reduce the driver's view. Ensure usage complies with pertinent vehicle codes of your state, province, territory, or country.

1.2 About Precautions on Using

  1. Before installation, check all accessories carefully to ensure the product and accessories are correct and complete.
  2. To ensure the dash cam runs well, format the micro SD card first before use.
  3. During installation, do not insert the car key into the power supply, and do not insert or remove any accessories like a micro SD card or rear cam when the dash cam is powered on. These actions should be completed when power is turned off.
  4. The screen in the dash cam is just a preview, not the original view. For best viewing, plug the memory card into a computer. If you need to remove it from the dash cam, turn off the dash cam first.
  5. Examine, check, and verify the dash cam at least every 3 months, including the memory card, to ensure video reception and recording are working properly. For each use, verify that the dash cam unit, visible lights, and audible sounds are working normally.
  6. For some mobile phone models, if the TsCam APP cannot connect to the preview, turn on airplane mode on the mobile phone and try again.

1.3 About Memory Card

  1. Use a genuine micro SD card with 64G(MINI)-256G(MAX) of Class 10, U3 Speed or above. We recommend using Class 10, U3 LEXAR High Endurance TF cards.
  2. Insert or remove the micro SD card only when the dash cam is turned off. (Do not operate it when it is powered on).
  3. Do not take the card out when the dash cam is recording to prevent important video files from being lost.
  4. When inserting a new card, format it on the dash cam before use. The 'Format' option is available in the dash cam menu.
  5. The memory card may become damaged or deteriorated after repeated cycles of overwriting, affecting its ability to save video and image files. If this occurs, immediately replace it with a new memory card.
  6. The micro SD card should be formatted once a month to maximize its lifetime.

2. Product Overview

2.1 Camera Overview

The TiESFONG A99 is a 4-channel dash cam designed for comprehensive vehicle recording. It features flexible rotation for blind spot coverage, precise GPS tracking, and acute night vision perception with WDR technology.

TiESFONG A99 4-Channel Dash Cam
Figure 1: TiESFONG A99 4-Channel Dash Cam with 360° recording capability, Wi-Fi, and GPS tracking.
Flexible Rotation for Blind Spot Coverage
Figure 2: Flexible rotation of the dash cam cameras to cover left and right blind spots, aiding in accident recording.
GPS Positioning and Precise Driving Track
Figure 3: Built-in GPS positioning system for clear vehicle position and secure track recording.
Acute Night Vision Perception with WDR
Figure 4: Acute night vision perception with Wide Dynamic Range (WDR) for clear recording in varying light conditions (too bright, normal, too dark).
Dash Cam Dimensions
Figure 5: Dimensions of the dash cam: 18.5cm (7.28 inch) length, 9.5cm (3.74 inch) width (main body), 5cm (1.97 inch) height (main body), 3.5cm (1.38 inch) height (side cameras).

Camera Components

No.NameDescription
1GPS Jack Slot2.5mm round hole for connecting with GPS Cable.
2Rear Cam Jack Slot2.5mm round hole for connecting with Rear Cam.
3Type-C USB PortFor power on.
4Restore Factory Settings HoleForce restore factory settings.
5TF Card SlotFor inserting TF Card (Micro SD Card).
6Left/Right CamLeft/Right Camera (tear off protective film before use).
7Infrared LED Light4 IR LED lights enhance night vision in the car.
8Front CamFront Facing Camera for video recording road events (tear off protective film before use).
9OK ButtonFunction differs by page; see 'Functional Explanation'.
10Down ButtonFunction differs by page; see 'Functional Explanation'.
11Up ButtonFunction differs by page; see 'Functional Explanation'.
12M ButtonFunction differs by page; see 'Functional Explanation'.
13Power ButtonFunction differs by page; see 'Functional Explanation'.

About Working LED Light

  • Blue light is always bright: Powered on (but not recording).
  • Blue light blinking: Recording is in progress.

2.2 Main Page Details: Icons and Functions

The upper and lower information columns on the main page will automatically hide after 6 seconds without any operation. Press any key to activate them.

Icon Explanation:

  • Memory Card:
    • ✓: Memory card inserted / Memory card correct.
    • ✗: No memory card / Memory card error.
  • Loop Record Time:
    • 1: Loop recording in 1 minute.
    • 2: Loop recording in 2 minutes.
    • 3: Loop recording in 3 minutes.
  • G-Sensor:
    • OFF: G-Sensor is OFF.
    • LOW: G-Sensor is ON (Low sensitivity).
    • MEDIUM: G-Sensor is ON (Medium sensitivity).
    • HIGH: G-Sensor is ON (High sensitivity).
  • GPS Tracking:
    • OFF: GPS Tracking is OFF.
    • ON (Not Connected): GPS Tracking is ON but not connected.
    • ON (Connected): GPS Tracking is ON and connected.
  • IR LED Light:
    • OFF: IR LED Light is OFF.
    • ON: IR LED Light in always-ON mode.
    • AUTO: IR LED Light in automatic-ON mode.
  • Emergency Lock:
    • Unlocked: Emergency lockout not triggered.
    • Locked: Trigger emergency lock recording.

    Note: If an emergency lock is triggered, the locked icon will appear in the center of the screen, and the current video will be saved in the event folder.

  • Lens Resolution Mode: This position shows the selected lens combination mode.
  • Voice Recording Sign:
    • ON: Voice Recording is ON.
    • OFF: Voice Recording is OFF.
  • WiFi:
    • OFF: WiFi is OFF.
    • ON (Not Connected): WiFi is ON but not connected.
    • ON (Connected): WiFi is ON and connected.
  • Recording Sign:
    • Red dot and red font (e.g., 00:01:00): Recording in progress.
    • No red dot and white font (e.g., 00:00:00): Not recording.
  • Camera Lens Screen: Displays the number of lenses according to the selected resolution mode.
    • Upper Left: Front Cam
    • Lower Left: Left Cam
    • Upper Right: Rear Cam
    • Lower Right: Right Cam
  • WiFi Information: The WiFi function is equivalent to Bluetooth. You can instantly connect to the dash cam within a 10FT range (when ON) to view, download, and share videos.
    • WiFi SSID: TiesFong_Cam_XXXX (Dedicated WiFi account - not recommended to modify).
    • WiFi PWD: 12345678 (Initial WiFi password).
  • GPS Tracking Data: Displays recorded driving speed (KMH or MPH).

Key Function Board on the Main Page

On the main page, each button corresponds to two functions: a short press (left function) and a long press (about 3 seconds, right function).

  • Power Button:
    • Long press: Power ON/OFF.
    • Short press: Open/Close the screen.
  • M Button:
    • Long press: Enter the Playback page (will stop recording).
    • Short press: Enter the Menu page (will stop recording).
  • Up Button:
    • Long press: Enter the Playback page.
    • Short press: Trigger emergency lock to lock the current video clip (20 seconds).
  • Down Button:
    • Long press: Take a photo.
    • Short press: Switching Lens Screen.
  • OK Button:
    • Long press: Turn WiFi ON/OFF.
    • Short press: Start/Stop Recording.

3. Installation

3.1 About Installing the Memory Card

  1. Insert a new Micro SD card into the card slot and then power on the dash cam.
  2. After the dash cam is turned on, press the M button to enter the Settings page.
  3. In the Setting page, press the Down button to switch to the option of 'Format', and press the OK button to enter.
  4. Then select the 'YES' option and press the OK button to confirm formatting.
  5. A blue frame will appear: "please wait...". Be patient while the SD card is formatted.
  6. When formatting is complete, a checkmark icon will be displayed. After formatting, press the M button to return to the recording interface, and the dash cam will automatically start recording.

Important Notes:

  • While waiting for 'please wait...', ensure the text in the blue frame confirms success (checkmark) or failure (X).
  • The dash cam will periodically remind you to format the memory card. If you see this, the files will not be deleted automatically unless you perform the formatting operation.
  • Do not use bad or low-speed memory cards, as this can lead to recording failure or loss.
  • Before formatting, check the memory card for any videos that need to be saved separately to avoid accidental deletion.

3.2 Installing the Cam onto the Car Windshield

3.2.1 Suggested Installation Location

Before installation, power on the dash cam and check if the recording angle of the front and interior lenses are appropriate through the recording view.

3.2.2 About Electrostatic Stickers

Function: To protect the car windshield or car window film.

Paste Method:

  1. Confirm the installation position of the dash cam, and wipe the area with screen cleaning paper.
  2. Tear off the protective film from the electrostatic sticker and stick it on the selected position.
  3. Use a scraper to remove any air bubbles between the sticker and the glass.

PS: Please stick it on a flat surface without air bubbles, otherwise it will not be firm!

3.2.3 About Installing the Bracket

  1. Align the mount with the dash cam mount interface, then push it from right to left until the mount is installed.
  2. Tear off the red protective film on the 3M Stick Bracket.
  3. Attach the bracket to the Electrostatic Sticker, press for about 10-20 seconds, and let the Electrostatic Sticker and the 3M stick fully fit firmly.

PS: Please be sure to press firmly. And look through the outside glass of the car to confirm whether it is fully fitted!

3.3 Installing the Power Cord

3.3.1 About Connecting the Power Cable

  1. Connect the TYPE-C USB port to the power port of the dash cam.
  2. Tape the Dash Cam to the top of the car's front windshield.
  3. Use a Pry Bar to carefully run the power cord along the slit on the edge of the windshield and hide it inside the car slit.
  4. Start your car; the dash cam will auto power on and start recording.

3.3.2 About the Power Cable of the Rear Cam

  1. Confirm that the BMW 5-pin connector between the Rear Cam Cable and Power Cable is fully connected.
  2. Insert the 2.5mm round hole interface of the Rear Cam into the 'Rear' jack slot of the dash cam.
  3. Use a Pry Bar to carefully run the power cord along the gap in the roof and hide it up to the back of the car.
  4. Confirm the position of the Rear Cam to be installed.

Two mounting options for the Rear Cam:

  1. Mounted on the rear windshield of the vehicle inside the vehicle. (No holes need to be drilled for this method; just stick it to the glass with 3M adhesive).
  2. Mounted on the outside of the vehicle in the trunk above the license plate. (This method requires drilling holes).
TiESFONG A99 Package Contents
Figure 6: Package contents including A99-Host, H63 Rear Cam, GPS Cable, Cig Charger Cable (TYPE-C), and User Manual.

4. Basic Operation

4.1 Power ON/OFF

When the dash cam is plugged into the power cable and the vehicle turns on, it will automatically turn on.

  • Manually: Long press the Power button to power it ON or OFF.
  • Automatically: The dash cam will power off if the power cable is disconnected or the vehicle is turned off.

4.2 WiFi Function

4.2.1 WiFi Function Instructions

  1. Scan the QR code below on your mobile phone to download the APP or search for "viidure" on your app store to download and install.
  2. WiFi Name (SSID): Tiesfong_Cam_XXXX (WIFI Serial Number)
  3. WiFi password (PWD): 12345678 (Initial Unified Password)

Viidure App QR Code

Figure 7: QR code for Viidure App download.

4.2.2 WiFi Connection Steps

  1. Turn on the WiFi function of the dash cam. (Shortcut: Long press the OK button for 3 seconds to turn on WiFi in the Recording page).
  2. Enter the WLAN interface of your phone settings, find "Tiesfong_Cam_XXXX".
  3. Enter the password to connect to the dash cam's WiFi account.
  4. Open the 'viidure' APP to connect the WiFi account.

Important Notes:

  • It is not recommended to modify the WiFi Name.
  • If you need to modify the WiFi password, connect to the APP to modify it in settings.
  • If the SSID of the dash cam cannot be found in the "WLAN" list in your phone settings, restart the WLAN and swipe the 'NETWORKS' list.

4.3 View Playback On Computer

4.3.1 Folders in the Memory Card

  • 'Event' Folder: Contains locked video files (20-second clips) triggered by G-SENSOR or manually locked. These files are protected and not overwritten by auto-loop.
  • 'Normal' Folder: Contains normal recorded video files. These videos are automatically overwritten and deleted in a cyclical loop.
  • 'Park' Folder: Contains parking monitoring video files. These videos are automatically overwritten and deleted in a cyclical loop.
  • 'Photo' Folder: Contains photos captured by the recorder. These photos are automatically overwritten and deleted in a cyclical loop.

Important: Be careful when deleting files from the 'Event' folder. If there are important videos, back them up. Clean the video files in your memory card regularly, especially from the 'Event' folder, as they are not overwritten by auto-loop. Formatting the memory card once every 1-3 months is recommended to prevent the event folder from occupying too much space and to prolong the memory card's life.

4.3.2 Computer View File Description

  1. Pull out the Micro SD card from the dash cam and insert it into a Card Reader.
  2. Connect the Card Reader to the USB port of the computer; it will appear as a removable disk.
  3. When playing videos or browsing photos, corresponding software may need to be installed on the computer. (Video format: MP4 / Photo format: JPG).
  4. Select the equivalent folder to view the video you want.
  5. After viewing, insert the memory card directly back into the card slot of the dash cam. (It is recommended not to format it on the computer).

4.4 GPS Function

4.4.1 GPS Status

  • When GPS is not connected or has no signal, the satellite icon is red or orange. Red means strong signal (not connected), orange means weak signal (not connected).
  • The display shows 12 zeros for the 12 signal channels.
  • When GPS is connected or has a signal, the satellite icon is green.
  • The signal channels do not necessarily have to be all full or have values to work.

4.4.2 Speed Calibration

The default for the dash cam is 0 km/h. This is for speed compensation. For example, if you set the calibration to 5 mph, and your driving speed is 60 mph, the dash cam will show 55 mph. This allows you to adjust the displayed speed.

4.4.3 GPS Data Display

  1. After successful GPS positioning, Speed will be displayed in the lower right corner of the dash cam's recording page.
  2. After successful GPS positioning, Speed / Latitude & Longitude will display in the lower left corner of the recorded video.

4.4.4 Check GPS Data on APP

  1. For Android System: To use the map to view GPS tracks, you need to download the offline map first. (Setting Path: More - APP Settings - Offline Map).
  2. Select the video you want to view and download.
  3. After downloading, click on the local album in the APP.

PS: After downloading the video to the local album, if you want to view the track, you need to disconnect the phone from the machine and keep your phone connected to the Internet, because the track needs to read the Gaode map packet.

4.4.5 Check GPS Data on Computer

  1. Pull out the used Micro SD card from the dash cam and insert it into the Card Reader.
  2. Connect the Card Reader to the USB port of the computer, open the removable disk.
  3. In the root folder of the memory card, there is a software "GXPlayer".
  4. When you use the software for the first time, set it up. Press the Settings button in the upper right corner to make personalized content settings.

PS: Please stop playing, otherwise you can't change the map successfully!

5. Maintenance

5.1 About Backup Files

  • If you want to store important videos or photos for a long time, it is recommended to copy the files from the memory card to a computer for storage.
  • Do not create new folder storage on the memory card, as this will reduce the effective use of memory card space.

5.2 Memory Card Care

  • Format the micro SD card once a month to maximize its lifetime.
  • Replace the memory card immediately if it becomes damaged or deteriorated.

6. Troubleshooting (FAQ)

Q1: Is it possible to use my own TYPE-C connector power cord? And is it recommended to use the car's USB port to power the dash cam?
A1: We do not recommend powering the dash cam with your own power cord or your car's USB port. The multi-lens logger requires 5V 2.5A. Many car USB ports only provide 2.1A, which may not stably power the recorder. It is recommended to use the cigarette lighter car charger port or the fuse box connector with the standard 5V 2.5A power cables provided.
Q2: If the recorder is set to Off-screen recording, how do I judge its working status? Is it power on or is it recording?
A2: If Off-screen recording is set, judge the working status by the working light on the right side of the screen. If the blue light is always on, the recorder is on but not recording. If the blue light is blinking, the recorder is on and recording.
Q3: Is it normal for the dash cam to get hot during operation? Will it be dangerous?
A3: Multi-lens dash cams have relatively high power consumption and need to dissipate heat, so getting warm is normal.
  1. The dash cam material is ABS+PC, which is flame retardant.
  2. It does not have a built-in rechargeable battery, preventing spontaneous combustion or explosion.
  3. The dash cam is resistant to low and high temperatures, with a working temperature range of -20°C to 65°C (-4°F to 149°F).
  4. It has a high-temperature protection mechanism; if it exceeds normal operating temperature, it will automatically power off.
  5. If you find the screen temperature relatively high, use the 'Screen Save' function in 'System Settings' and set it to 'Off-screen recording'.
Q4: Why is the date and time incorrect?
A4: This usually indicates an error in settings. The default time is GMT-5:00 (U.S. time). You need to personalize settings according to your country's time zone.

Follow these steps:

  1. Go to the Setting page, find 'Time Zone', and check if it's set to your country's corresponding time zone.
  2. Turn on the GPS function.
  3. Turn on WiFi and connect to the APP.
  4. After setting the 'Time Zone', with GPS function and connecting to the APP, the date and time will usually update and save automatically.
Q5: Why are the videos all 1/2/3 minute segments? Can I change it to always record and save as a whole video?
A5: Videos are saved in segments according to the clip type. The recorder is always recording, and 3 minutes per clip is a reasonable length.

Reason:

  1. Segmented video allows for better preservation. When the memory card is full, the earliest video clips are automatically deleted for loop recording.
  2. Saving video in segments allows you to view corresponding video segments according to the time.
Q6: The Left/Right Cam sometimes has a red flash, why is that? Is this normal?
A6: This is usually due to devices or electronics with face recognition technology near the dash cam. Observe if your mobile phone is on when the Left/Right Cam flashes red, or if your car has a device with facial recognition.

Perform a verification operation:

  1. Lock your mobile phone screen and do not point it at your face to re-observe if the Left/Right Cam is still flashing red.
  2. Cover any face recognition device in your car with your hand to re-watch the Left/Right Cam and see if there is still a red flash.
Q7: Why only a few seconds of video clips can be saved in the memory card?
A7: This usually happens because videos in the locked 'Event' folder are occupying the memory card, preventing normal recording or indicating a damaged memory card.

Follow these steps:

  1. Go to the Playback page, find the 'Event' folder, and check for many videos.
  2. Check if these videos are useful; if so, save them.
  3. Clean up useless videos. We suggest formatting the entire memory card.
  4. When formatting, pay attention to the screen to confirm 'formatted successfully'.
  5. If formatted successfully, let the dash cam record for 5-10 minutes, then check the Playback page to see if video duration in the video folder is normal (3 minutes).
  6. If formatting fails, replace the memory card. (Replace the memory card as required).
Q8: The video recorded from the Left/Right Cam will have a color difference and turn purple? Why?
A8: The Left/Right Cam has four infrared night vision lights and a built-in red filter for night vision, causing some red color difference. A special night vision filter enhances night vision. This filter and color aberration do not affect the clarity of the recorded video.
Q9: The Front/Rear Cam are normal in color, but the Left/Right Cam are black and white? Why is this? What should I do?
A9: This is usually a setup issue. If the IR LED is set to 'ON', the Left/Right Cam will appear black and white regardless of ambient light.

Follow these steps:

  1. Go to the Setting page, find 'IR LED'.
  2. Set the IR LED option to 'Auto'.
Q10: WiFi is connected to the phone, but cannot connect to Viidure APP, what should I do?
A10:

Follow these steps:

  1. Close the Viidure APP on your phone.
  2. Go to your phone settings, find the WLAN function.
  3. Find the dash cam's WiFi account you connected to and click the blue icon on the far right to enter its detail page.
  4. Find 'Forget this network' and confirm.
  5. Turn OFF the dash cam, wait 10 seconds, then turn it back ON and turn ON its WiFi.
  6. Rediscover the dash cam's WiFi account in your mobile phone's WLAN and link it.
  7. Reopen the Viidure app to connect.

If it still doesn't connect properly, uninstall the Viidure APP, reinstall it, and follow the steps above again.

Q11: Dash cam's WiFi is successfully turned on, but the phone cannot search/connect to the WiFi account, what should I do?
A11: This is mainly because the mobile phone's WLAN signal is not retrieving the dash cam's WiFi account.

Follow these steps:

  1. Go to your mobile phone's 'Settings', find the WLAN function, and turn it off.
  2. Go back to 'Settings' and turn on Airplane Mode.
  3. After turning the dash cam OFF and back ON, turn the dash cam's WiFi function back ON.
  4. Re-enter the WLAN function and turn it on so that the mobile phone will automatically search for the dash cam's WiFi account.
Q12: WiFi is not opening/opening abnormally in dash cam, what should I do?
A12: This usually indicates a stuck program in the dash cam.

Follow these steps:

  1. Go to the Setting page, find the 'Reset' function, click OK, and select YES.
  2. Wait for the dash cam to reboot, then try to turn on the WiFi function again.

If WiFi still won't open after a 'RESET', contact support with your order number, 'Version Info' (Page 17), and the unique SN barcode on the bottom of the dash cam for upgrade software.

Q13: Started the car but the dash cam didn't turn on properly. It keeps rebooting/not working properly (stuck machine/screen/buttons not responding, etc.), what should I do?
A13: Perform a simple troubleshooting test. (It's best to record the process to share with support).

Follow these steps:

  1. Remove all power cables (power cable and rear cam cable) from the dash cam.
  2. Remove the memory card from the card slot.
  3. Re-energize the dash cam using the cigarette lighter car charger cable.

Then provide the following information to support for a solution: 1. Order number, 2. A rehearsal video (if recorded), 3. Unique SN barcode on the bottom of the dash cam, 4. 'Version Info' from the Setting page (Page 17, if the dash cam can be turned on).

7. Specifications

CategoryDescription
Brand NameTiESFONG
Item TypeCar DVR
Assembly ModePortable Recorder
Chipset ManufacturerMSTAR
Imaging SensorGC2053
Pixels800Mega
Number Of Lenses4
Camera Resolution1920x1080
View angle4*150°
ApertureF1.6+F1.8
Video CodeH.265
Video FormatMP4
Frames Per Second25
Maximum Video Frame Rate25
DisplayIPS
Built-in ScreenYes
Touch ScreenNo
Screen Ratio16:9
Memory Card Required Reading SpeedClass 10
Max External Memory256G
Data Storage CapacityMemory Card
GPS loggerExternal
Special FeaturesG-Sensor, Waterproof, Automatic White Balance, Wide Dynamic Range, WiFi function, Bluetooth, Speed and Coordinates Recording, 3D DNR, External GPS
Loop-Cycle Recording FeatureYes
Audio RecordedYes
NightShot FunctionYes
Rear CameraYes
Original PackageYes
Power SourceCorded Electric
Input/OutputTYPE-C
Is Batteries IncludedYes
Batterybuilt-in
Battery Typebutton cell (lithium ion polymer)
Battery Life0
Battery Capacity(mAh)1 mAh
Working Temperature-20℃~65℃
Cable Length3M
Weight162.6g
Dimensions (W x H x D)18.5*5.3*5.3cm
APP CompatibilityYES (Viidure)
OSD LanguageChinese (Simplified), Chinese (Traditional), English, French, German, Italian, Japanese, Korean, Russian, Spanish
InterfaceWi-Fi, Micro SD/TF, Bluetooth
CertificationCE, FCC, RoHS
OriginMainland China

8. User Tips

  • Power Supply: Always use the provided cigarette lighter car charger or fuse box connector with the standard 5V 2.5A power cables for stable operation. Car USB ports may not provide sufficient power.
  • Memory Card Management: Regularly format your Micro SD card (at least once a month) to maintain optimal performance and prevent storage issues. Back up important 'Event' videos to a computer, as they are not automatically overwritten.
  • Parking Monitor: While the dash cam is advertised with 24/7 parking monitor support, ensure the G-sensor is activated for this feature to function. If you have concerns about its activation, refer to the G-sensor settings.
  • Left/Right Camera Color: If the Left/Right cameras appear black and white, check the 'IR LED' setting in the menu and set it to 'Auto'. This allows the camera to adjust based on ambient light.
  • WiFi Connectivity: If you experience issues connecting the Viidure APP, try restarting your phone's WLAN, enabling airplane mode briefly, and then re-enabling WLAN to refresh network lists. If persistent, a dash cam reset or firmware update might be necessary.
  • Troubleshooting: For persistent issues like the dash cam not turning on or rebooting, try removing all cables and the memory card, then re-powering with only the cigarette lighter charger. Document the process with a video if contacting support.

9. Warranty and Support

If you have any questions about your product, please feel free to contact us. Inquiries are usually answered within 12-24 hours.

After-Sales Services: tiesfong@gmail.com

We are firmly committed to continuously improving our products and services. We welcome your constructive feedback and suggestions on how we can do even better.

Viidure App and YouTube Channel

For additional support, tutorials, and related videos, you can download the Viidure App or visit our official YouTube channel.

Viidure App QR Code
Scan for Viidure App
TiESFONG YouTube QR Code
Scan for TiESFONG YouTube

Made in CHINA

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.