RADIOMASTER ZORRO

Contents

Radiomaster Zorro Radio Controller User Manual

Model: ZORRO

1. Introduction

Thank you for purchasing the RadioMaster ZORRO radio system. The ZORRO is an advanced and highly versatile radio controller, suitable for users of any skill level. To ensure safe and reliable operation, please read this manual carefully before use.

As software and hardware are continuously improved, the information in this manual is subject to change without prior notice. For the most up-to-date information and radio firmware, please visit the RadioMaster website.

The ZORRO is an open-source, ergonomically designed radio with powerful multi-protocol capability. It can bind to most contemporary protocols on the market. The ZORRO runs EdgeTX, an open-source operating system. For more information, visit the EdgeTX links.

2. Safety Information

⚠️ Disclaimer:

For recreation use only. Illegal modification of drones/planes is prohibited. Please also pay attention to the relevant laws and regulations on the use of drones/planes in your country/area to ensure legal use.

Radio-controlled models often contain sharp components like propellers that rotate at high RPM. Always use common sense and proceed with caution when operating or maintaining the model. Always disconnect power to the model AND remove propellers (if applicable) during assembly or maintenance.

Never operate the ZORRO radio system under the following conditions:

  • In severe weather or strong windy conditions, such as rain, hail, snow, storms, or electromagnetic environments.
  • In limited visibility.
  • In the proximity of other people, property, high-voltage power lines, public roads, vehicles, or animals.
  • When feeling unwell, or under the influence of drugs or alcohol.
  • If the ZORRO radio system/model is damaged or showing signs of interference.
  • In areas with high 2.4GHz interference or where 2.4GHz radios are prohibited.
  • When the TX/RX battery is low.
  • In areas where local regulations prohibit the use of R/C aircraft.

3. Setup

3.1. Antenna Installation

⚠️ Important:

Install the provided antenna in the top of the radio BEFORE installing batteries and turning on the radio. DO NOT operate the radio without the antenna installed and the internal RF module powered on. Doing so will damage the internal RF module and will not be covered under warranty.

The Zorro features a foldable antenna for convenience.

Foldable antenna on the Radiomaster Zorro controller
Figure 3.1: Foldable antenna in folded and extended positions.

3.2. Battery Installation and Charging

The ZORRO is powered by two 3.7V 18350 Lithium-ion cells (not included) and is charged using the built-in USB-C port. The charging circuitry is designed for charging 3.7V Lithium-ion batteries only. The nominal voltage is 3.7V and the maximum charging voltage is 4.2V.

⚠️ Important:

DO NOT charge 3.6V LiFe and 3.6V 18650 Lithium-ion packs with the onboard charger. Charging or using the wrong battery chemistry/polarity may cause permanent damage to the PCB and in certain situations cause fires.

The controller also supports an external 2S battery power supply for extended use.

Radiomaster Zorro battery compartments for 18350 cells
Figure 3.2: View of the 18350 battery compartments.
USB-C charging port on the Radiomaster Zorro controller
Figure 3.3: USB-C direct charging port.
External 2S battery power supply connection on Radiomaster Zorro
Figure 3.4: Support for external 2S battery power supply.

3.3. RF Configurations

The ZORRO comes with various internal RF options depending on the package purchased, including CC2500 single-chip multi-protocol, 4-in-1 multi-protocol, or ELRS 2.4GHz. These configurations support a wide range of protocols.

Diagram showing four RF configurations: 4IN1, CC2500, SX1280 (ELRS), CC2500+TBS
Figure 3.5: Available RF configurations.

3.4. Mode Switching (Mode 1 and Mode 2)

The Zorro radio supports switching between Mode 1 and Mode 2 without disassembly. The default factory mode is Mode 2. Adjustments for spring tension and self-centering/throttle can be made via screws on the back of the controller.

Diagram showing spring tension and self-centering/throttle adjuster screws for Mode 1/2 switching
Figure 3.6: Adjustments for Mode 1 and Mode 2 switching.

3.5. Gimbal Adjustment

The Zorro features adjustable HALL Gimbals. Stick travel can be adjusted by turning a screw clockwise to increase travel (Max. 54°) or counter-clockwise to decrease travel (Min. 38°).

Diagram showing adjustable HALL Gimbals with stick travel adjustment
Figure 3.7: Adjustable HALL Gimbals and stick travel adjustment.

3.6. External Module Bay

The Zorro Radio includes an external module bay for use with Crossfire / ELRS and other compatible modules (e.g., TBS Nano Crossfire / Nano Tracer / IRC Ghost).

Diagram showing the external module bay compatible with TBS Crossfire and ExpressLRS
Figure 3.8: External module bay for compatible modules.

3.7. DIY Attachment Points

The controller features DIY attachment points and auxiliary buttons on the back for customization.

Diagram highlighting DIY attachment points and auxiliary buttons on the back of the controller
Figure 3.9: DIY attachment points and auxiliary buttons.

4. Operating Instructions

4.1. Quick Start Overview

The Radiomaster Zorro features a monochrome LCD screen (128*64) with adjustable brightness. Key controls include SB 3-Position and SE 2-Position switches, T1-T4 Trims, SYS button, RTN button, PAGE buttons, MDL button, Metal Menu Wheel, and TELE button. The power button is centrally located.

Quick Start Guide diagram of the Zorro controller layout with labeled buttons and switches
Figure 4.1: Quick Start Guide diagram of the Zorro controller.

The back of the controller includes an audio output, SD card slot, DSC trainer port, and USB port.

Back of the Zorro controller with labeled ports: Audio output, DSC port, SD card slot, USB port
Figure 4.2: Back view with labeled ports.

4.2. Operating System

The ZORRO supports OpenTX and EdgeTX open-source operating systems.

Image showing OpenTX and EdgeTX logos with the Zorro controller screen
Figure 4.3: OpenTX & EdgeTX support.

4.3. Model & Protocol Selection

To select a model and protocol:

  1. Long press the MDL button to enter the model settings.
  2. Select MULTI in the SETUP page.
  3. Select the protocol to be used in the sub-options. The system will automatically turn on the corresponding RF module according to the selected RF protocol.

The Bind [BND] option is used to start the binding process. The Range [RNG] button can reduce the power to 1/30 to facilitate testing of remote-control distance.

4.4. Binding Instructions

Follow these steps to bind your ZORRO controller to a receiver:

  1. Turn OFF the transmitter.
  2. Cycle power to the receiver 3 times. The receiver LED will flash twice, indicating bind mode.
  3. Turn ON the transmitter, long press the SYS button and choose ExpressLRS LUA under the TOOLS menu. Scroll to [Bind] and press enter.
  4. The LED on the receiver should now be solid, indicating a successful bind.

⚠️ Attention for 4in1/CC2500 Users:

The receiver you are using may require frequency tuning. Refer to the multi-module website for instructions: www.multi-module.org/using-the-module/frequency-tuning

For ZORRO ExpressLRS units, Dynamic Power and a 500Hz or lower packet rate are recommended to extend battery life and minimize heat generation by the internal module.

5. Maintenance

5.1. Battery Care

Please check the voltage and condition of the battery regularly and never charge unattended. Always charge in a safe area away from combustible materials. Refrain from charging if the remote control gets wet or damaged in any way. DO NOT charge with the polarity reversed.

5.2. Firmware Updates

The ZORRO is pre-installed with factory-approved EdgeTX firmware. To download the latest software manual and firmware, please visit the RadioMaster website: www.radiomasterrc.com

Further firmware information can be found at:

⚠️ Caution:

Only attempt to update the firmware if you are confident in the process. Incorrect firmware updates may cause the remote control to become inoperable.

6. Troubleshooting

If the remote control becomes inoperable after a firmware update, it is likely due to an incorrect update process. Refer to the firmware update instructions carefully. If issues persist, consult the official websites for detailed troubleshooting guides or contact support.

If the radio system shows signs of interference or damage, cease operation immediately and inspect the unit. Do not operate a damaged unit.

7. Specifications

Feature CC2500 Version 4in1 Version ELRS Version
Physical Dimensions 170*159*108mm
Weight 350 grams
Operating Frequency 2.400GHz-2.480GHz
Internal RF Options CC2500 multi-protocol 4-in-1 multi-protocol ELRS
Supported Protocols Module dependent Module dependent ELRS
Antenna Gain Folding 2db
Operational Current 160mA@8.4V
Operational Voltage 6.6-8.4v DC
Control Distance > 2km Receiver and Power Output dependent
Operating System OpenTX / EdgeTX Compatible
Control Channels Maximum 16 (Rx dependent)
Display 128*64 Monochrome LCD
Battery 2 x 18350 (Not included)
Charging Built in USB-C Charging
Gimbal Hall-effect
Module Bay Nano Size (Compatible with TBS Nano Crossfire / Nano Tracer / IRC Ghost)
Firmware Upgrade Method Via USB or SD card
Oversized LCD screen of the Radiomaster Zorro controller with adjustable brightness
Figure 7.1: Oversized LCD with adjustable brightness.

8. Warranty & Support

If you encounter any problems with your remote control hardware, please retain your proof of purchase and contact the retailer where you purchased the product.

You may also visit the official RadioMaster website for warranty support: www.radiomasterrc.com/contact

9. User Tips

  • Always ensure the antenna is properly installed before powering on the radio to prevent damage to the internal RF module.
  • Regularly check battery voltage and condition. Charge in a safe, attended area away from flammable materials.
  • Familiarize yourself with the EdgeTX or OpenTX operating system for optimal control and customization.
  • For 4in1/CC2500 users, verify if your receiver requires frequency tuning and follow the instructions on the multi-module website.
  • For ExpressLRS users, consider enabling Dynamic Power and using a 500Hz or lower packet rate to balance battery life and heat generation.

10. Compliance Information

10.1. EU Simple Declaration of Conformity

RadioMaster declares that the radio equipment ZORRO is in compliance with EU directives Directive 2014/53/EU.

Manufacturer: ShenZhen RadioMaster Co., Ltd, 3F Yang Tian Building, Area 72 Xing Dong community, Xin An Street, Bao An district, Shen Zhen City, Guangdong Province, China.

10.2. FCC Information

FCC ID: 2A337ZORRO

This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Antenna Separation Distance:

When operating your RadioMaster transmitter, please be sure to maintain a separation distance of at least 20 cm between your body (excluding fingers, hands, wrists, ankles and feet) and the antenna to meet RF exposure safety requirements as determined by FCC regulations.

Full text of the declaration of conformity is available at: www.radiomasterrc.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.