1. Introduction
This manual provides essential information for the safe and effective installation, operation, and maintenance of your RACBOX 5.5-inch LED Round Taillight. This product is an auxiliary accessory designed for automotive lighting, intended for normal replacement and upgrade of original vehicle lights. It is not for illegal modification or use. Please read all instructions carefully before use.
Video: Product demonstration showing the lights in action.
Image: Two RACBOX LED taillights installed on the rear of a trailer, illustrating typical application.
2. Safety & Warnings
Important Safety Information:
Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture.
3. Product Overview
The RACBOX 5.5-inch LED Round Taillight is a multi-function lighting solution for various vehicles. It features a durable ABS plastic construction with an acrylic lamp housing, offering 92% light transmission. The light provides flowing amber turn signals, a red tail light, and a brighter red brake light.
Image: Detail showing the acrylic lamp housing and its 92% light transmission.
Image: Demonstration of the taillight's waterproof feature with water splashing.
4. Specifications
| Feature | Specification |
|---|---|
| Product Name | LED Round Brake Taillight |
| Model Name | Multi-function LED Tail Light |
| Brand | RACBOX |
| Item Type | Tail Light Assembly |
| Input Voltage | 12-24V DC |
| Light Color | Flowing Amber + Red Light |
| Light Dimension | 5.5 Inch Round (approx. 140mm diameter, 41mm depth) |
| Material | ABS plastic (housing), Acrylic (lens) |
| Features | Waterproof and Shockproof |
| Wiring | 4 Lines Connection (Yellow, Blue, Red, Black) |
| Wire Length | 260mm |
| Mounting Bolt Spacing | 44mm |
| Origin | Mainland China |
| Suitable for | 12/24V Vehicles (Truck, Trailer, Van, Bus, 4x4, Pickup, Jeep, Volvo) |
Image: Dimensions of the LED Round Taillight.
5. Setup & Installation
Follow these steps for proper installation:
- Turn off the vehicle engine and disconnect the power supply to avoid short circuit.
- Locate the mounting position of the original tail light.
- Remove the fixing screws or clips that hold the stock light assembly.
- Unplug the power connector and take off the original tail light.
- Install the new tail light assembly into the mounting position.
- Secure the light assembly with screws or clips to ensure stable installation.
- Connect the power plug correctly. If the light does not work, reverse the plug polarity.
- Test all light functions to ensure normal operation.
- Recheck all screws and connections to make sure they are firm and reliable.
Wiring Diagram:
Image: Detailed wiring diagram for the 4-line connection.
- Yellow Wire: Turn signal
- Blue Wire: Tail light
- Red Wire: Brake light
- Black Wire: Negative pole
Image: Rear view of the taillight showing mounting bolts and wire connections.
6. Operation
Once properly installed and connected, the taillight will function as follows:
- Turn Signal: When activated, the amber LEDs will illuminate with a flowing sequence, indicating a turn.
- Tail Light: When vehicle lights are on, the red outer ring and internal red LEDs will illuminate steadily.
- Brake Light: When the brake pedal is pressed, the red LEDs will illuminate brighter, providing a clear stop signal.
Image: Demonstration of Turn Signal, Tail Light, and Brake Light functions.
7. Maintenance
To ensure the longevity and optimal performance of your LED taillight:
- Regularly clean the lens with a soft, damp cloth to remove dirt and debris. Avoid abrasive cleaners.
- Periodically check all wiring connections for tightness and signs of corrosion.
- Inspect the light for any physical damage. If damaged, replace the unit to maintain safety and compliance.
- Ensure the mounting screws or clips remain secure.
8. Troubleshooting
Light Not Functioning:
- Check Power Connection: Ensure all wires are securely connected according to the wiring diagram.
- Reverse Polarity: If the light does not work after initial connection, try reversing the plug polarity.
- Vehicle Power: Verify that the vehicle's electrical system is providing power to the taillight circuit.
- Fuse Check: Inspect the relevant fuse in your vehicle's fuse box.
Intermittent Function:
- Loose Connections: Check all wiring connections for looseness or corrosion.
- Grounding Issue: Ensure the negative pole (black wire) has a solid ground connection to the vehicle chassis.
If problems persist after checking these points, consult a qualified automotive technician.
9. User Tips
No specific user tips were available from reviews or Q&A for this product at this time. However, general advice for LED taillights includes:
- Consider applying dielectric grease to electrical connections to prevent corrosion, especially in harsh environments.
- When replacing, ensure the new light is securely mounted to prevent vibration damage.
10. Warranty & Support
For warranty information or technical support, please refer to the seller's policies or contact the manufacturer directly. Keep your purchase receipt as proof of purchase.
Manufacturer: Guangzhou Bai Ji Tun Trading Co., Ltd, C116, No.1489, Fanghua Road Baiyun Guangzhou, tdlaccount@126.com
EU Authorized Representative: APEX CE SPECIALISTS LIMITED, UNIT 3D NORTH POINT HOUSE, NORTH POINT BUSINESS PARK, NEW MALLOW ROAD, CORK, T23 AT2P, IRELAND, info@apex-ce.com
For further assistance, please contact your point of purchase.
11. Compliance Information
This product is an auxiliary accessory for automotive lighting and is only used for the normal replacement and upgrade of the original car lights, not for illegal modification or illegal use. The products meet the relevant national automotive lighting industry standards, and have undergone strict quality testing before leaving the factory, and are qualified to leave the factory.