AV Access KD-E20

Contents

AV Access KD-E20 Dual Monitor KVM Dock Switcher

Model: KD-E20

1. Introduction

1.1 Overview

The KD-E20 is a multi-function 2x1 KVM switch docking station designed for personal home office and entertainment use. It serves as a central device, allowing you to connect two USB-C laptops and two HDMI monitors. This device simplifies connectivity and switching, enabling you to share various external devices such as a mouse, keyboard, mobile hard disk, camera, or speakerphone between your laptops.

1.2 Features

  • 2x1 KVM Switch Docking: Seamlessly switch between two USB-C laptops to two HDMI 2.0 monitors.
  • Dual Full-Featured USB-C Inputs: Supports 4K@60Hz video transmission, USB 3.0 data, and 100W charging (requires an external USB-C power adapter).
  • High Refresh Rate Support: Compatible with resolutions like 2560×1440@144Hz/120Hz and 1080P@240Hz/165Hz/144Hz/120Hz.
  • Multiple Peripheral Ports:
    • 3x USB 3.0 Type-A ports (5Gbps data transfer; two ports provide 5V/1A power output, one port provides 5V/1.5A power output).
    • 1x USB 3.0 Type-C port (data only, 5Gbps data transfer, 1.5A current output).
    • 2x USB 2.0 Type-A ports (480Mbps data transfer).
    • 1x SDXC card slot (supports up to 2TB SDXC cards, max 104MB/s data transmission).
    • 1x LAN port (1Gb Ethernet performance, supports simultaneous connection for two USB-C laptops).
    • 1x 3.5mm TRRS (stereo + mic) headset port.
  • CEC Trigger on HDMI Outputs: Automatically sends a CEC Power-ON command to the corresponding HDMI output port when an input signal is detected on the current channel.
  • Automatic Wake-up Function: Wakes up the standby computer automatically when switching inputs.
  • Wired Remote Controller Support: Connects to the EXB01 Wired Remote Controller for convenient remote switching.

2. Package Contents

Before proceeding with the installation, please verify that all items listed below are included in your package:

  • KD-E20 KVM Dock Switcher x 1
  • Power Adapter (DC 12V/3A) x 1
  • USB 3.2 Gen 2 Type-C to Type-C Cable (L=1m) x 2
  • Wired Remote Controller (EXB01) x 1
  • User Manual x 1

3. Setup and Connection

3.1 Important Warnings

  • Before wiring, ensure all devices are disconnected from their power sources.
  • Always connect and disconnect cables gently to prevent damage.
  • When using the USB-C In port for laptop charging, an external USB-C power adapter (up to 100W) must be connected to the dedicated Charging port on the KVM switcher. The KVM switcher itself requires its own power adapter.
  • For optimal performance and to avoid warning messages, use your laptop's original USB-C power adapter or an equivalent with the required specifications.

3.2 Panel Layout

Familiarize yourself with the ports and buttons on the KVM Dock Switcher:

AV Access KD-E20 KVM Docking Station with labeled ports (Front View)
Figure 1: Front and Rear Panel Overview of the KD-E20 KVM Dock Switcher

Front Panel Ports:

No. Name Description
1 Power Button & LED Press to power the device on/off. The LED indicates power status (On: powered on; Off: powered off).
2 USB Device (USB 2.0 Type-A) Connect keyboard, mouse, or wireless receiver.
3 Headphone 3.5mm TRRS headphone jack. Connect a headset with microphone. Ensure "AV Access KD-E20" is selected on the connected host device for headphone switching.
4 SD Slot SDXC port for inserting SDXC cards.
5 USB 3.0 (1.0A) Type-A Connect USB 3.0 high-speed devices for KVM function. Provides 5V/1A power output.
6 USB-C (data only) USB 3.0 Type-C port for data transmission only. Provides 1.5A current output.
7 Switch Button & Input LEDs Press to switch the input source. LEDs indicate the currently selected input (On: selected; Off: not selected).

Rear Panel Ports:

No. Name Description
1 DC 12V Connect the provided power adapter to power the KVM switcher.
2 CTL Connect the Wired Remote Controller (EXB01) for input switching.
3 USB 3.0 (1.5A) Type-A Connect high-power USB devices, such as a USB Camera. Provides 5V/1.5A power output.
4 LAN Connect to a network switch or router. Provides 1Gb Ethernet for two USB-C laptops simultaneously.
5 Monitor (A&B) Connect to HDMI monitors.
6 & 8 Charging Special port for charging. Connect an additional USB-C power adapter (up to 100W) to charge a laptop connected to USB-C In.
7 & 9 USB-C In Connect to USB-C sources (e.g., laptops). Supports video, audio, USB, and Ethernet signals. Supports DP MST mode for two 4K@60Hz videos (laptop must support DP 1.4a and MST). Supports PD 2.0 for up to 100W laptop charging (via Charging port).

3.3 Connection Diagram

Follow the diagram below to connect your laptops, monitors, and peripherals to the KVM Dock Switcher.

Detailed connection diagram for the AV Access KD-E20 KVM Dock Switcher.
Figure 2: Comprehensive Connection Diagram

This diagram illustrates how to connect two laptops (Laptop 1 and Laptop 2) to two monitors (Monitor 1 and Monitor 2) using the KVM switcher. It also shows connections for a power adapter, the EXB01 wired remote controller, a Cat Cable for LAN, and various USB peripherals like a keyboard, mouse, headset, printer, hard disk, and iPhone. Note that laptop power adapters are not included with the KVM switcher.

3.4 Dual Monitor Setup

The KD-E20 allows two laptops to share two monitors, enhancing work efficiency or gaming experience.

Setup showing two laptops sharing two monitors via the KVM switch.
Figure 3: Two Laptops Sharing Two Monitors

4. Operating Instructions

4.1 Switching Between Laptops

The KVM Dock Switcher offers two convenient ways to switch between your connected laptops:

  • Panel Switch Button: Press the physical button on the front panel of the KVM switcher to toggle between Laptop 1 and Laptop 2.
  • Wired Remote Controller (EXB01): Use the included remote controller for quick and easy switching from your desk.
Two methods for switching inputs on the KVM Dock Switcher: Panel Switch Button and Wired Remote Controller (EXB01).
Figure 4: Switching Methods

4.2 Display Modes

The KVM switcher supports various display modes depending on your operating system:

Multiple display modes supported by the KVM Dock Switcher for macOS and Windows.
Figure 5: Multiple Display Modes
  • macOS: The USB-C port of a MacBook cannot support extended display mode. Displays will typically mirror or show independent content on each monitor, but not an extended desktop across both monitors from a single MacBook USB-C port.
  • Windows: Two monitors can display content from one computer at a time, supporting both mirrored and extended desktop configurations.

4.3 KVM Switch in Action

Watch this video to see the AV Access KD-E20 KVM Dock Switcher in operation, demonstrating seamless switching between connected laptops.

Video 1: KVM Dock Switcher Demonstration

5. Charging Functionality

The KVM switcher provides a dedicated USB-C charging port for each USB-C In port. This allows you to connect an external USB-C charger (not included) to power the laptop connected to the corresponding USB-C In port. This port supports a maximum charging power of 100W.

Important Note: The adapter connected to the Charging port will only charge the laptop and will not power the KVM switcher itself. The KVM switcher must be powered by its own dedicated power adapter (DC 12V/3A) included in the accessories. It is recommended to use the USB-C charger that comes with your laptop or an equivalent power adapter. Using a low-power USB-C charger may cause your laptop to display a warning message.

Diagram illustrating 100W reverse charging for USB-C laptops via the KVM switch.
Figure 6: 100W Reverse Charging for USB-C Laptop

6. Resolution Support

Both USB-C In ports support DisplayPort (DP) alt mode and DP Multi-Stream Transport (MST) outputs. Each USB-C In port can output two different videos simultaneously, with a maximum support of two 4K@60Hz outputs. The actual output resolution depends on the DP standard of the USB-C port on your connected laptop.

6.1 For Windows Laptops:

DP 1.4 HBR3 with DSC DP 1.4 HBR3 without DSC DP 1.2 HBR2
Out 1 Out 2 Out 1 Out 2 Out 1 Out 2
Single Video Output 4K@60Hz / 4K@30Hz / 4K@30Hz /
Dual Video Output 4K@60Hz 4K@60Hz 1080P@60Hz 1080P@60Hz 1080P@60Hz 1080P@60Hz

6.2 For macOS Laptops (MacBook with M series):

Out 1 Out 2
Single Video Output 4K@60Hz /
Dual Video Output 4K@60Hz 4K@60Hz (Mirrored)

7. Maintenance and Care

7.1 General Warnings

  • Do not open, disassemble, or repair this product yourself.
  • Avoid using the device in hot, cold, dusty, or humid environments.
  • Wipe the device with a dry cloth for cleaning.
  • Avoid dropping the device, as severe impact can cause mechanical damage, malfunction, or surface scratches.

8. Troubleshooting

If you encounter issues with your KD-E20 KVM Dock Switcher, please refer to the following common troubleshooting steps:

  • No Power: Ensure the DC 12V power adapter is securely connected to the KVM switcher and plugged into a working power outlet.
  • No Display Output:
    • Verify that the HDMI cables are securely connected between the KVM switcher and your monitors.
    • Check that the USB-C cables from your laptops are correctly connected to the USB-C In ports (7 & 9) on the KVM switcher.
    • Confirm that your laptops are powered on and outputting a video signal.
    • Ensure the correct input source is selected on the KVM switcher (indicated by the Input LEDs).
    • If using macOS, remember that extended display mode may not be supported via a single USB-C port.
  • Peripherals Not Working (Keyboard/Mouse/USB Devices):
    • Check that USB devices are properly connected to the appropriate USB ports on the KVM switcher.
    • Ensure the KVM switcher is powered on and the correct laptop input is selected.
    • If connecting high-power USB devices, use the USB 3.0 (1.5A) port.
  • Laptop Not Charging:
    • Confirm that an external USB-C power adapter (up to 100W) is connected to the KVM switcher's dedicated Charging port (6 or 8).
    • Verify that the USB-C cable from the laptop is connected to the corresponding USB-C In port (7 or 9).
    • Ensure the external USB-C power adapter is functional and provides sufficient wattage.
  • Network Connectivity Issues:
    • Check the Ethernet cable connection between the KVM switcher's LAN port and your network switch/router.
    • Ensure your network is active and functioning correctly.

9. User Tips

  • Always ensure all cables are firmly seated in their respective ports to prevent intermittent connections.
  • For the best display experience, use high-quality HDMI and USB-C cables that support the desired resolutions and refresh rates.
  • If you frequently switch between laptops, consider using the wired remote controller for added convenience.

10. Specifications

10.1 Technical Specifications

Category Specification
Input USB-C (100W Charging PD 2.0, USB 3.0 up to 5Gbps, 4K@60Hz DP MST two video transmission)
Output HDMI 2.0b (up to 4K@60Hz 4:4:4 8bit, HDCP 2.2)
USB-C x1 (up to 5Gb/s, 1.5A power output)
Peripheral and Expansion USB-A x5:
  • 3x USB 3.0 ports (up to 5Gb/s; two with 1A power output, one with 1.5A power output)
  • 2x USB 2.0 ports (up to 480Mb/s)
SDXC card: Up to 104MB/s, maximum support 2TB
LAN: RJ-45 connector, 1Gb Ethernet performance (works with two USB-C Laptops simultaneously)
Input/Output Resolution Supported SMPTE: 1280x720P, 1920x1080I/P, 2560x1080, 3840x1080, 3840x2160, 4096x2160 (various Hz)
VESA: 800x600, 1024x768, 1280x768, 1280x800, 1280x960, 1280x1024, 1360x768, 1366x768, 1400x1050, 1440x900, 1600x900, 1600x1200, 1680x1050, 1920x1200, 2560x1440 (various Hz)
Audio Format Supported HDMI Out: PCM 2.0/5.1/7.1, Dolby TrueHD, Dolby Atmos, DTS-HD Master Audio, DTS:X
USB-C In: PCM 2.0/5.1/7.1, Dolby TrueHD, Dolby Atmos, DTS-HD Master Audio, DTS:X
Headphone: Stereo

10.2 General Specifications

Category Specification
Operating Temperature 0°C to +45°C (32 to +113°F)
Storage Temperature -20°C to +70°C (-4 to +158°F)
Humidity 20% to 90%, non-condensing
Power Consumption 28.2W (Max)
Device Dimensions (W x H x D) 220mm x 25.2mm x 100mm / 8.66" x 0.99" x 3.94"
Product Weight 0.72kg / 1.59lbs

11. Warranty and Support

11.1 Limited Warranty

Products are backed by a limited 1-year parts and labor warranty. AV Access reserves the right to charge for services if the product is still remediable but the warranty card is unenforceable or inapplicable under the following conditions:

  • The original serial number (specified by AV Access) on the product has been removed, erased, replaced, defaced, or is illegible.
  • The warranty period has expired.
  • Defects are caused by repair, dismantling, or alteration by unauthorized service partners, or by improper use/handling not instructed in the User Guide.
  • Defects are caused by force majeure, including but not limited to accidents, fire, earthquake, lightning, tsunami, and war.
  • Services, configurations, and gifts promised by sales personnel are not covered by the normal contract.

AV Access reserves the right to interpret these cases and make changes at any time without notice.

11.2 Contact Support

Thank you for choosing AV Access products. If you have any questions or require technical assistance, please contact us via the following emails:

For additional documentation, including the full user manual in PDF format, please refer to the official product page or contact support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.