Haozee XFY-CGQ-ZBSOLG-Ni-IP65

Contents

Haozee Tuya Zigbee Solar Light Sensor User Manual

1. Introduction

Thank you for choosing the Haozee Tuya Zigbee Solar Light Sensor. This device is designed for intelligent indoor and outdoor brightness detection, enabling advanced automation in your smart home or agricultural setup. With its IP65 waterproof rating and solar power capabilities, it offers reliable performance in various environments.

This manual provides detailed instructions for the installation, operation, and maintenance of your solar light sensor. For a complete digital version of this manual, please refer to the official PDF document: User Manual (PDF).

Haozee Tuya Zigbee Solar Light Sensor, waterproof design

Figure 1: Haozee Tuya Zigbee Solar Light Sensor

2. Package Contents

Please check the package for the following items:

  • Solar Light Sensor: 1 unit (with built-in rechargeable battery)
  • Instruction Manual: 1 copy (Chinese and English)
  • Pry Tool: 1 sheet
  • Screw Pack: 1 set
  • Double-Sided Adhesive: 1 piece

3. Installation

Follow these steps to install your solar light sensor:

  1. Indoor Placement: For indoor use, place the sensor directly in the room where light intensity needs to be monitored.
  2. Outdoor Smooth Surfaces: For outdoor use on smooth surfaces like glass or tiles, use the provided 3M adhesive to secure the sensor. Ensure the surface is clean and dry before application.
  3. Outdoor Walls: For outdoor wall mounting, use the 3M adhesive along with the provided expansion screws for a secure fixation. This method is recommended for permanent outdoor installations.
Installation diagram for solar light sensor showing adhesive and screw mounting options

Figure 2: Installation Methods

4. Operation

4.1. Product Use

The sensor regularly collects outdoor light intensity and generates corresponding values. This real-time light intensity data is reported to your Internet of Things (IoT) platform (e.g., Tuya platform). It can be integrated with various smart devices such as electric curtains, electric awnings, smart switches, and smart sockets to enable intelligent control of household lighting, agricultural awnings, and other functions.

4.2. Operational Principle

Natural light is detected by a digital photosensitive IC chip and converted into a digital signal. This digital signal is then processed by a module loading algorithm to derive a unit light value. The sensor reports this data to the IoT platform (e.g., Tuya Smart Platform) via its integrated IoT module, supporting protocols like Zigbee.

4.3. Product Functionality

Once the IoT platform receives the light value, it can send this data to other controlled devices within the platform (e.g., smart light bulbs, smart switches, smart curtains). These actions are executed based on automation conditions set by the user in the APP (e.g., turning lights off when brightness exceeds a certain level, or turning them on when it falls below). Users can also directly view the current light intensity value through the APP.

4.4. Application Scenarios

The solar light sensor enhances smart home automation with intelligent sensing capabilities:

  • Automatic Light Switching (Living Room): Set lights to turn off automatically when brightness exceeds a threshold (e.g., 550 LUX) for energy saving.
  • Smart Curtain Control: Automate smart curtains to close when the room becomes too bright (e.g., >800 LUX) or open when it's too dark.
  • Warehouse Automation: Control lights, fans, or air conditioners in warehouses based on ambient light levels (e.g., turn off lights if >800 LUX).
  • Agricultural Tent Automation: Automatically open or close electric sunshades for agricultural tents based on light intensity (e.g., close if >1200 LUX).

5. Maintenance

5.1. Levels of Protection

The sensor features unique double protection technology. Its upper and lower covers are sealed with soft silicone rubber to prevent dust and moisture ingress. The IC chip has a light transmittance of over 93%, and the UV-resistant adhesive is transparent, ensuring accurate light detection. The full PCBA potting process further prevents water spray from entering the protective layer, contributing to its IP65 protection class.

5.2. General Care

To ensure optimal performance and longevity, especially for outdoor installations:

  • Periodically wipe the solar panel and sensor lens with a soft, damp cloth to remove any accumulated dust or debris.
  • Avoid using abrasive cleaners or solvents, as these can damage the device's casing or lens.
  • Ensure the sensor is not obstructed by foliage or other objects that could block sunlight or light detection.

6. Troubleshooting

6.1. Device Reset

If the device is not functioning as expected or you need to reconfigure it, you can perform a factory reset:

  • Remove the back cover of the sensor.
  • Press and hold the reset button for 5 seconds. The device will restore factory settings and enter reconfiguration mode.

6.2. Firmware Upgrade (Optional)

To initiate a firmware upgrade or enter a specific reconfiguration mode:

  • Tilt the sensor 45 degrees for 10 seconds.
  • Then, restore it to its original position. The device will enter the reconfiguration mode.

6.3. Common Issues

  • No Data Reporting: Ensure the device is within range of your Zigbee gateway and that the gateway is connected to the internet. Check the battery level.
  • Inaccurate Readings: Clean the sensor lens and ensure it is not obstructed. Verify the sensor is placed in an area representative of the light conditions you wish to monitor.
  • Connectivity Problems: Try restarting your Zigbee gateway. If issues persist, perform a device reset and re-pair it with your gateway.

7. Specifications

Product features overview: indoor/outdoor detection, AI automation, 83000LUX range, IP65, TI IC

Figure 3: Key Features

FeatureDescription
BrandHaozee (Neutral/OEM/ODM)
Model NumberXFY-CGQ-ZBSOLG-Ni-IP65 (Solar light sensor-Ni-MH)
Material/ColorABS+PC / White
Pilot LampLED (orange): 1
Use Ambient Temperature-20°C to +70°C
Levels of ProtectionIP65
Detection ZoneBrightness: 0 LUX ~ 83000 LUX
Sensitivity5 LUX at ≤100 LUX
ProtocolZigbee
High-Concerned ChemicalNone
OriginMainland China
Product Dimensions (Bottom)70mm (L) x 70mm (W) x 29mm (H)
Product Dimensions (Top)63mm (L) x 63mm (W) x 29mm (H)
Sensor/Gross Weight80g (with battery), 60g (without battery)
Sense ICOPT3004DNPR
Main Control ChipTLSR8258
Rated Power Consumption0.0010W (Max 0.0027W)
Power Supply ModeOutdoor: Solar energy for Ni-MH battery cycle. Indoor: Solar light charging for 1 day, usable for nearly a year.
Exploration Cycle5 seconds per report algorithm + 180 seconds fixed time; short press reset for active report.
Support PlatformsGraffiti intelligence (Tuya)
International CertificationROSH, CEred

8. Warranty and Support

For warranty information, technical support, or any inquiries regarding your Haozee Tuya Zigbee Solar Light Sensor, please contact your retailer or the manufacturer directly. Please refer to your purchase documentation for specific warranty terms and contact details.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.