Road Top Audi A5 S5 Multimedia Screen

Contents

Road Top Multimedia Screen User Manual

For Audi A5 S5 (2008-2016) 8.9" / 12.3" Touch Screen GPS Carplay Multimedia Player

1. Introduction

Thank you for choosing the Road Top Multimedia Screen. This manual provides detailed instructions for the installation, operation, and maintenance of your new car multimedia system. Please read this manual thoroughly before installation and use to ensure proper functionality and to avoid damage.

This system is designed to upgrade your Audi A5 S5 (2008-2016) with modern features like Wireless/Wired CarPlay, Android Auto, GPS navigation, and multimedia playback on an 8.9-inch or 12.3-inch high-resolution touch screen.

2. Product Contents

Please check the package contents against the list below:

  • 1x 8.9-inch or 12.3-inch Multimedia Smart Touchscreen
  • 1x Screen Bracket (model-dependent)
  • 1x Power Cable
  • 1x USB Cable
  • 1x AMI Cable (for equipped vehicles)
  • 1x Iron Frame and Screws
  • 1x Airbag Light Adapter Cable
Product Contents and Dimensions

Figure 2.1: Product contents and dimensions. The 8.9-inch screen measures 23cm x 9.8cm, and the 12.3-inch screen measures 30.4cm x 13.3cm. Included accessories are power cable, USB cable, AMI cable, and iron frame with screws.

3. Compatibility

This multimedia screen is compatible with Audi A5 and S5 models from 2008 to 2016. Compatibility depends on whether your car has GPS MMI 3G or no GPS.

Compatible Model List

Figure 3.1: Compatible models and system types. Audi A5 (2008-2016) with CAR HAVE GPS MMI 3G or CAR NO GPS.

3.1 Pre-installation Checks

Before purchasing and installing, ensure your car's dashboard matches the pictures provided and identify your car's system configuration:

  1. Identify your car system: Press the 'Settings' or 'Menu' button on your radio, go to 'Settings', scroll down, and find similar FM interfaces. This helps determine if you have 'No GPS (Low Configuration)' or 'GPS MMI 3G (High Configuration)'.
  2. Check head unit type: Compatible with 'Symphony', 'Concert' (Low configuration), or 'Multimedia' (High configuration). Not compatible with 'Chorus' or 'CD Changer' units.
Car System Identification

Figure 3.2: Guide to identify your car's system configuration (No GPS vs. GPS MMI 3G).

Head Unit Compatibility

Figure 3.3: Visual guide for compatible (Symphony, Concert, Multimedia) and incompatible (Chorus, CD Changer) head units.

4. Setup

Important: Ensure the vehicle's ignition is fully turned off before beginning installation. Operating or installing the unit with power on may cause permanent damage to the car audio system.

Professional assistance is recommended for users without relevant installation experience. You can also refer to online video guides for disassembly and installation.

4.1 Cable Connection Overview

Cable Connection Chart

Figure 4.1: General cable connection diagram. The main menu interface shows options for OEM, CarPlay, Android Auto, Bluetooth, AirPlay, AutoLink, and USB.

4.2 Detailed Installation Steps

  1. Head Unit Power Cable Connection: Disconnect the original power cable from the head unit. Attach it to the new wiring harness, then connect the new harness to the head unit's power port.
  2. LVDS Cable Connection: Disconnect the original LVDS cable from the OEM screen and connect it to the new Linux-compatible screen. Leave other OEM cables disconnected.
  3. Gateway Control Module Cable Connection: The gateway control module is located on the passenger side, accessible after removing the glove box. Connect the provided gateway control module cable between the original socket and the new gateway control module.
  4. Airbag Light Adapter Cable Connection: Connect the included airbag light adapter cable. Ensure correct connection to the original car double flash interface and the airbag lamp holder interface (connect the emergency light board and hide it). Connect the Linux screen's shell emergency light socket.
  5. MIC Cable Connection: Connect the microphone cable from the back of the Linux screen to the microphone port on the new bracket.
  6. Clamps Removal and Transfer: Disassemble the clamps from the OEM bracket and transfer them to the new bracket. Replace the OEM bracket with the new one and secure it to the vehicle.
  7. Iron Frame and Linux Screen Installation: Remove the OEM screen. Fix the new iron frame using the OEM screws. Then, fix the Linux screen with new screws.
  8. AMI Cable Connection (For Equipped Vehicles): If your vehicle has an AMI port, connect the provided AMI cable to enable CarPlay audio through the vehicle's AMI/AUX system. AMI ports can be found in the glove box, central console box, or behind media interface doors.

4.3 Basic Software Setup

After installation, complete the following basic settings for proper OEM system function:

4.3.1 OEM System Resolution Setup

If the OEM interface shows screen distortion or icon misalignment, adjust the resolution:

  1. Navigate to: Setup > Car Settings > Original Car's Screen Resolution.
  2. For MMI 3G-equipped vehicles:
    • If your original car's screen is 5.8 inches, choose MMI 3G 400X240 or MMI 3G 400X240 (2).
    • If your original car's screen is 7 inches, choose MMI 3G 800x480.

4.3.2 Sound Setup

This unit supports two audio output modes: AMI/AUX Mode and Original Bluetooth Mode.

AUX Audio Output Mode:
  1. Disconnect any existing Bluetooth connection from your phone to the vehicle.
  2. In the system menu, set Setup > System > Use Car's BT Channel to OFF.
  3. Switch to OEM MMI3G System: Navigate to Media, then select

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.