Mercedes Benz A1693260700

Contents

Rear Shock Absorber Installation & Operation Manual

Model: A1693260700

1. Product Overview

The Rear Shock Absorber is a core shock absorption component of the automotive chassis suspension system. It is installed between the rear axle and the vehicle frame/body. Its primary function is to absorb vibrations generated by road bumps, suppress spring rebound, reduce body sway, ensure close contact between the wheels and the ground, and enhance the smoothness, stability, and handling safety of the vehicle.

This product features a hydraulic/pneumatic damping structure, utilizing high-strength seamless steel pipe and forged aluminum alloy. It includes built-in wear-resistant seals and high-performance damping oil.

Rear Shock Absorber Strut

Figure 1: Rear Shock Absorber Strut (Side View)

Rear Shock Absorber Strut with mounting hardware

Figure 2: Rear Shock Absorber Strut (Angled View)

2. Product Features & Materials

2.1. Material Advantages

  • Main Cylinder: Made from 20# seamless precision steel pipe with a wall thickness of ≥3.5mm, ensuring high compressive strength and resistance to deformation or leakage.
  • Piston Rod: Constructed from 45# quenched and tempered steel with chrome plating. It features a surface hardness of ≥HRC50, providing excellent wear and corrosion resistance, with a straightness error of ≤0.02mm.
  • Damping Component: Utilizes hydraulic damping oil (with excellent high-temperature stability) or a pneumatic damping structure. Combined with multi-layer valve plates, it allows for precise damping adjustment.
  • Sealing System: Features an NBR+PTFE composite seal, which is oil and high-temperature resistant, ensuring long-lasting sealing performance and preventing damping oil leakage.
  • Connecting Component: Forged aluminum alloy upper and lower joints provide a lightweight yet high-strength design. Equipped with 10.9-grade high-strength fixing bolts.

2.2. Core Features

  • Operating Temperature: Designed to operate within a range of -40°C to +120°C, making it suitable for extreme climates and complex road conditions.
  • Rated Load: Supports a rated load of 500~1500kg (adapted to specific vehicle models), meeting the requirements for various vehicle weights.
  • Damping Coefficient: Ranges from 15~35 N·s/mm, effectively attenuating vibrations and improving driving smoothness.
  • Service Life: Expected to last 8 years or 120,000km under normal use, with damping performance attenuation of ≤10%, and no oil leakage or abnormal noise.

3. Specifications

AttributeValue
Product NameRear Shock Absorber
Model NumberA1693260700
OEM NO.A1693260700
Manufacturer Part NumberA1693260700
Compatible VehiclesMercedes Benz W169, W245, A160, A180, B200
Product TypeElectronic assembly excluded
Country/Region of ManufactureCHINA
OriginMainland China
Operating Temperature-40°C ~ +120°C
Rated Load500~1500kg (vehicle model adapted)
Installation PositionRear axle and frame/vehicle body

4. Installation Guide

Note: This guide provides general instructions. For detailed vehicle-specific procedures, always refer to your vehicle's service manual. Installation should be performed by qualified automotive maintenance technicians.

4.1. Pre-Installation Preparation

4.1.1. Tools & Materials Required

ItemDescription
Socket Wrench Set14-27mm
Torque Wrench0-500 N·m
Spring CompressorSpecial tool, load-bearing ≥2 tons
Jack & Safety StandsFor lifting and securing vehicle
Hex Key Set8-14mm
Combination Wrench Set12-24mm
Lint-free RagFor cleaning surfaces
Shock Absorber CleanerSpecial cleaning agent
Anti-rust LubricantFor bolts and connections
Safety GearNon-slip gloves, safety goggles, safety helmet
New Rear Shock Absorber KitIncludes matching bolts, lock nuts, washers, dust cover
Thread LockerMedium strength (e.g., Loctite 243)
Copper PasteFor installation contact surfaces

4.1.2. Safety Instructions

  • Safety Protection: Always wear non-slip gloves, safety goggles, and a safety helmet throughout the operation. This prevents injuries from falling tools, spring rebound, or splashing parts. Ensure no irrelevant personnel are in the work area.
  • Vehicle Preparation: Park the vehicle on a level, hard ground. Engage the parking brake and secure wheels with chocks. Loosen the rear wheel bolts (do not fully remove them). Lift the rear of the vehicle with a jack and place safety stands for support. Never rely solely on the jack. Ensure the vehicle body is stable.
  • Component Protection: When using a spring compressor, compress the spring evenly. Avoid excessive one-sided compression, which can cause the spring to eject. During disassembly, avoid colliding with brake lines and ABS sensor wiring harnesses to prevent damage and leakage.
  • Professional Operation: Chassis suspension system adjustments are involved. Installation must be performed by qualified automotive maintenance technicians. Improper installation can lead to unstable vehicle operation and brake failure, causing serious traffic accidents.
  • Pair Replacement: It is highly recommended to replace both left and right rear shock absorbers simultaneously. This ensures balanced body force and prevents driving deviation or abnormal noise due to unilateral performance differences.

4.2. Installation Steps

4.2.1. Remove Old Rear Shock Absorber

  1. Remove Rear Wheel: Fully unscrew the rear wheel fixing bolts with a socket wrench. Remove the rear wheel and place it aside carefully to avoid scratching the tire.
  2. Locate Shock Absorber: The rear shock absorber is typically installed vertically between the rear axle and the vehicle body shock mount. The upper part connects to the vehicle body, and the lower part connects to the rear axle bracket. (Some models may have an oblique installation; confirm connection points).
  3. Mark Installation Position: Use a marker to mark the installation angle and bolt positions of the upper and lower connection points. This ensures the new part is installed at the same angle.
  4. Remove Upper Fixing Parts: Use a wrench to loosen the bolts and nuts connecting the upper part of the shock absorber to the vehicle body (usually 2-3 pieces). Remove and keep these connecting parts.
  5. Remove Lower Fixing Parts: Use a socket wrench to loosen the bolts connecting the lower part of the shock absorber to the rear axle (usually 1-2 pieces). Separate these connection points.
  6. Take Out Old Shock Absorber: Gently shake the old shock absorber to fully separate it from its mounting seat. Slowly remove it. Inspect the old shock absorber for damage such as oil leakage, piston rod bending, or dust cover damage.

4.2.2. Cleaning & Inspection (Critical Step)

  1. Clean Installation Contact Surface: Wipe the mounting surfaces of the vehicle body shock mount and rear axle connection bracket with a special cleaning agent for shock absorbers. Remove oil, rust, and impurities. Dry with compressed air. Ensure the installation surface is flat and undamaged.
  2. Inspect Related Parts: Check if the shock spring is deformed or broken, if the shock mount is loose, and if the brake pipeline and sensor wiring harness are intact. Repair or replace any damaged components synchronously.
  3. Inspect New Shock Absorber: Confirm the new shock absorber model is compatible with the vehicle. Check for scratches or leakage on the main body. Ensure the piston rod extends and retracts smoothly without jamming. Verify that the dust cover and seals are firmly installed, and that all matching bolts and nuts are of complete specifications.
  4. Prepare Installation Accessories: Apply a small amount of copper paste to the installation contact surface of the new shock absorber. Apply medium-strength thread locker to the bolt threads.

4.2.3. Install New Rear Shock Absorber (Core Step)

  1. Position Installation: Align the new shock absorber with the mounting seat according to the marked angle. Ensure the upper and lower connection holes are fully aligned. (Do not force alignment to avoid thread damage).
  2. Pre-tighten Lower Bolts: Insert the lower fixing bolts, place washers and lock nuts, and pre-tighten by hand (do not tighten fully yet).
  3. Pre-tighten Upper Bolts: Insert the upper fixing bolts, place washers and nuts, and pre-tighten by hand to ensure the shock absorber is properly positioned.
  4. Tighten Bolts: Use a torque wrench to tighten all bolts according to the original factory standard torque. (Upper part: 80-120 N·m; Lower part: 120-150 N·m, refer to your vehicle manual for exact values). Tighten in two steps to ensure the installation surface is closely fitted.
  5. Install Dust Cover: Place the dust cover over the piston rod of the shock absorber and fix it in place. This prevents dust and impurities from entering the sealing system.

4.2.4. Reset & Test

  1. Install Rear Wheel: Place the rear wheel back on the hub. Tighten the fixing bolts in a diagonal order (pre-tightening torque: 80-100 N·m).
  2. Remove Tools: Slowly lower the jack, remove the safety stands, and allow the vehicle to fully rest on the ground.
  3. Preliminary Test: Start the vehicle and drive at idle speed on a flat road. Check if the vehicle body is stable and if there is any abnormal noise in the rear wheel area.
  4. Road Test: Drive on a safe road. Test the shock absorption effect under low-speed bumpy road conditions, during braking, and steering. Observe for excessive body sway or deviation. The vehicle should run stably without resonance noise when driving at high speed. If all checks are satisfactory, the installation is complete.

5. Maintenance

5.1. Replacement Timing

There is no fixed replacement interval. Replace the shock absorber immediately if any of the following symptoms occur:

  • Shock absorber oil leakage (oil stains on the piston rod surface) or damaged dust cover.
  • Severe body jitter during vehicle driving, or significant rear-end sag during braking.
  • Obvious body roll during steering, driving deviation, or high-speed jitter.
  • Bent piston rod, stuck extension and retraction of the shock absorber, or accompanied by abnormal noise.
  • The vehicle has been used for more than 8 years or 120,000km (preventive replacement).

5.2. Initial Use (First 1000km after installation)

Avoid high-speed sudden acceleration, sudden braking, and off-road driving. Focus on observing:

  • No oil leakage or abnormal noise from the shock absorber; normal extension and retraction of the piston rod.
  • Stable vehicle driving, no excessive sway or deviation.
  • No loose fixing bolts or abnormal wear at the installation position.

5.3. Regular Inspection

  • Every 5,000-10,000km (Routine Maintenance): Check if the shock absorber is leaking oil, if the fixing bolts are loose, if the dust cover is intact. Clean the surface sediment and oil.
  • Every 30,000km: Recheck the bolt torque with a torque wrench. Check if the piston rod surface has scratches or rust, and if the shock spring is deformed.
  • After Use in Extreme Conditions: (e.g., long-term off-roading, frequent overloading, driving on rough roads): Increase inspection frequency and shorten the replacement cycle by 30%.

5.4. Daily Maintenance

  • Regular Cleaning: Clean the surface of the shock absorber with a high-pressure water gun to remove sediment and oil, preventing corrosion of the main body and seals.
  • Rust Protection: In coastal or dusty areas, apply anti-rust lubricant to the bolt connections every 6 months to prevent thread rust.
  • Avoid Overloading: Do not continuously overload the vehicle or tow heavy objects. This prevents the shock absorber from bearing pressure exceeding its rated load, which can lead to damping failure.

5.5. Storage Requirements

Unused rear shock absorbers should be stored vertically in a dry, cool, and ventilated place. Avoid heavy pressure, collision, and direct sunlight. The recommended storage temperature is -20°C to +60°C. Apply anti-rust oil to the piston rod surface to prevent rust.

6. Troubleshooting

ProblemPossible Cause / Solution
Body jitter remains severe after installation
  1. Confirm shock absorber model compatibility; replace with correct model.
  2. Check installation angle; readjust according to mark.
  3. Check if shock spring is deformed; replace spring synchronously.
Shock absorber has oil leakage
  1. Check if seal is installed correctly; replace with new seal.
  2. Confirm bolt tightening torque meets standard; retighten.
  3. Check if shock absorber cylinder is deformed; replace with intact product.
Abnormal noise occurs during driving
  1. Check if shock absorber is closely attached to mounting seat; clean impurities and tighten bolts.
  2. Check if dust cover is damaged; replace with new one.
  3. Check if shock spring is loose; reposition the installation.
Vehicle deviates during driving
  1. Confirm left and right shock absorbers are same model; replace with matching shock absorbers.
  2. Check if installation angle is symmetrical; readjust.
  3. Perform four-wheel alignment to correct wheel parameters.
Piston rod extension and retraction is stuck
  1. Check if piston rod is bent; replace with intact shock absorber.
  2. Clean impurities and rust on piston rod surface; apply special lubricating oil.
  3. Check if damping oil is insufficient; contact professionals for supplementation.

7. Warranty & Support

7.1. Disclaimer

This manual provides guidance for product installation and use. Before operation, always confirm the compatibility between the product and your vehicle. The manufacturer shall not be liable for any product damage, vehicle failure, or personal safety accidents caused by improper installation, product misuse, unauthorized modification, or use of non-original accessories. For installation quality and safety, all installation procedures must be performed by professional technicians.

7.2. Important Notes

  • Specification Matching: Select a rear shock absorber compatible with your specific vehicle/model/frame number. Rear shock absorbers of different models have different installation sizes, rated loads, and damping coefficients—they are not interchangeable. Misuse will cause unstable driving and shock absorption failure.
  • Torque Standard: Tighten bolts strictly according to the specified torque. Insufficient torque will cause vibration and loosening, while excessive tightening will damage the mounting seat or threads, affecting driving safety.
  • No Modification: Do not arbitrarily cut or weld the shock absorber structure. Do not adjust the damping valve plate or replace non-original seals. Modifications will damage shock absorption performance and cause safety accidents.
  • Accessory Compatibility: Always use matching high-strength bolts and lock nuts during installation. Do not use ordinary bolts or substitutes with inconsistent sizes. Replace aged shock springs and dust covers synchronously.
  • Cross-Border Compliance: This product meets EU CE certification, RoHS environmental standards, and German WEEE certification. For sales in the EU, product packaging must be marked with EU responsible person information. For sales in the US, it must comply with EPA standards and be marked with relevant compliance logos to ensure tax and logistics compliance.

For further support or inquiries, please refer to the official product page or contact your supplier.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.