ZIBOO FT-1000W

Contents

ZIBOO FT-1000W Solar MPPT Meter User Manual

Photovoltaic Multimeter for PV Module Testing

1. Introduction

The ZIBOO FT-1000W Solar MPPT Meter is a professional-grade photovoltaic multimeter designed for testing solar panel power. This ergonomic device features a large LCD screen, offering high precision, performance, shock resistance, safety, and stability. It accurately measures the maximum power point (Pmax), maximum voltage point (Vmp), maximum current point (Imp), open-circuit voltage (Voc), and short-circuit current (Isc) of solar panels. Equipped with reverse operation protection and internal over-temperature protection, it is an essential tool for solar panel manufacturers, installation systems, and maintenance professionals.

ZIBOO FT-1000W Solar MPPT Meter with test leads and accessories

Figure 1: ZIBOO FT-1000W Solar MPPT Meter with included test leads.

2. Safety Precautions

Please read and understand all safety instructions before operating the device.

  1. This product adheres to Chinese and European solar energy industry safety standards.
  2. Operate the instrument strictly according to prescribed safety regulations.
  3. Measure only within the specified safety range to prevent damage.
  4. Do not touch conductors with voltage exceeding 30V to avoid electric shock.
  5. If measurement exceeds range, a high-voltage lightning symbol and buzzer alarm will activate. Exercise caution.
  6. Avoid using in flammable, explosive, or other special hazardous environments.
  7. Replace batteries promptly when the low battery symbol is displayed to ensure accurate measurements.
  8. Before measurement, inspect test leads for damage or leaks. Do not use if damaged.
  9. Ensure correct connection of standard MC4 test leads, verifying positive and negative polarity.
  10. Pay attention to all safety symbols and warnings on the device.
  11. WARNING: Do not perform tests greater than 82.0V.
  12. WARNING: Do not perform tests greater than 35.2A.

3. Product Overview

3.1. Components

Contents of the ZIBOO FT-1000W Solar MPPT Meter package

Figure 2: Package contents including the meter, test leads, and tools.

The standard package includes:

  • ZIBOO FT-1000W Solar MPPT Meter
  • Special Test Leads (MC4 dedicated test cable)
  • Standard MC4 dedicated wrench tool (x2)
  • Manual & Gift Box
  • Magnet strap (optional accessory)

3.2. Device Layout

Front view diagram of the ZIBOO FT-1000W Solar MPPT Meter with labeled parts

Figure 3: Front view of the meter with key components labeled.

  1. LCD Display
  2. Function Button Group
  3. Black Test Input Port (for negative voltage V-)
  4. Red Test Input Port (for positive voltage V+)
Back view diagram of the ZIBOO FT-1000W Solar MPPT Meter

Figure 4: Back view of the meter showing lanyard position.

4. Setup

4.1. Battery Installation

The meter requires 3 AAA 1.5V batteries (not included). To install or replace batteries:

  1. Ensure the meter is disconnected from any circuits.
  2. Locate the battery cover on the back of the device.
  3. Unscrew the battery cover screws.
  4. Insert 3 AAA 1.5V batteries, observing correct polarity.
  5. Replace the battery cover and tighten the screws securely.
Diagram illustrating how to open the battery cover for the ZIBOO FT-1000W Solar MPPT Meter

Figure 5: Battery cover removal for battery replacement.

4.2. Connecting Test Leads

Connect the provided MC4 dedicated test cables to the input ports on the meter. Ensure the black lead is connected to the negative input port (V-) and the red lead to the positive input port (V+). Always verify the correct polarity when connecting to a solar panel or PV module.

5. Operation

5.1. Key Functions

  • Power Button (Power button icon): Press and hold for 2 seconds to turn the device ON or OFF.
  • MANUAL Button: Activates manual measurement mode.
  • AUTO Button: Activates automatic loop measurement mode.
  • H/Backlight icon Button: In measurement mode, press to hold the displayed data. Press and hold for 2 seconds to turn the backlight ON or OFF.
ZIBOO FT-1000W Solar MPPT Meter highlighting features like Auto Off, Backlight, Manual/Auto mode, and Data Hold

Figure 6: Key features of the Solar MPPT Meter.

5.2. Display Symbols and Measurements

ZIBOO FT-1000W Solar MPPT Meter displaying measurement ranges for Pmax, Vmp, Amp, Voc, and Isc

Figure 7: Meter display showing various measurement parameters.

  • Pmax (W): Maximum Power Point. The maximum power generated under strong light conditions. Range: 5-1000W.
  • Vmp (V): Maximum Voltage Point. The voltage at which maximum power is generated under strong light. Range: 12-80V.
  • Imp (A): Maximum Current Point. The current at which maximum power is generated under strong light. Range: 0-35A.
  • Voc (V): Open-Circuit Voltage. The voltage measured when the photovoltaic's positive and negative poles are open-circuited. Range: 12-80V.
  • Isc (A): Short-Circuit Current. The current measured when the photovoltaic's positive and negative poles are short-circuited. Range: 0-35A.
  • AUTO: Indicates automatic cyclic measurement mode.
  • Data Hold Symbol: Indicates that the current display is held.
  • Automatic Shutdown Symbol: Indicates the device will automatically shut down after approximately 10 minutes of inactivity.
  • Temperature Symbol: Indicates detection of excessive internal temperature.
  • Low Voltage Symbol: Prompt for battery replacement.
  • Caution Symbol (Caution symbol icon): Indicates a potential hazard.
  • CE Symbol: European Union CE certification.
  • WEEE Symbol: Compliant with the WEEE Recycling Directive.

5.3. Test Reference

The meter is suitable for testing various solar photovoltaic panels. Common voltage specifications include 12V, 18V, 24V, 36V, 48V, and 60V. Common power specifications include 60W, 100W, 200W, 300W, 500W, 600W, 700W, and 800W.

The test power (W) is calculated as: Vmp x Imp = W. For example, 48.0V x 11.0A = 528W.

6. Specifications

Detailed specifications table from the product packaging, comparing FT-1000W and FT-2000W models

Figure 8: Technical specifications for FT-1000W and FT-2000W models.

Parameter FT-1000W Resolution / Accuracy
Maximum Power (Pmax) 1000W 0.1W / ±(1.0%+10)
Maximum Voltage (Vmp) 12-80V 0.1V / ±(1.0%+5)
Maximum Current (Imp) 0-35A 0.1A / ±(1.0%+5)
Open Circuit Voltage (Voc) 12-80V 0.1V / ±(1.0%+5)
Short Circuit Current (Isc) 0-35A 0.1A / ±(1.5%+2)
Input Protection Anti-mistake input, positive and negative reverse protection, internal over-temperature protection
Sampling Rate 3 times/s
Overload Display "OL"
Auto Power Off Approx. 10 minutes
Operating Temperature 0-40°C
Accuracy (18-28°C, Humidity <75%) ±3°C ±5°C; 1 year
Storage Temperature -10-60°C, Humidity <80%
Pollution Grade 2
Altitude 0-2000m
Battery 3 x AAA 1.5V
Dimensions (H x W x D) 142.5 x 76 x 32 mm (5.61 x 2.99 x 1.26 inches)
Weight 198g (with standard battery)

7. Maintenance

7.1. Battery Replacement

Refer to Section 4.1 for detailed instructions on battery replacement. Always disconnect the meter from any circuits before opening the battery compartment to avoid electric shock.

7.2. General Care

  • Keep the instrument clean and dry.
  • Store the meter in a cool, dry place away from direct sunlight and extreme temperatures.
  • Only authorized and professionally experienced technicians should attempt to open the machine casing for repair. Improper repairs can cause damage and electric shock hazards.

8. Troubleshooting

  • Meter displays "OL" or buzzer alarms: The measurement has exceeded the instrument's range. Disconnect immediately and ensure your test parameters are within the specified limits.
  • Low battery symbol displayed: Replace the 3 AAA 1.5V batteries as soon as possible to ensure accurate readings.
  • No display or erratic readings: Check if the batteries are correctly installed and have sufficient charge. Inspect test leads for any damage or loose connections.
  • Product malfunction: If the issue cannot be resolved using the above steps, please contact official after-sales service for assistance. Do not attempt unauthorized repairs.

9. User Tips

  • Batteries Not Included: Remember that 3 AAA 1.5V batteries are required for operation and are not typically included in the package.
  • Test Leads Included: The meter comes with dedicated MC4 test leads, so you won't need to purchase them separately.
  • Read the Manual: The included instructions are in English and provide comprehensive guidance for safe and effective use.
  • Consider a Carrying Case: While the product comes with a gift box, a dedicated carrying case can help protect the meter and its accessories during transport and storage.

10. Warranty & Support

For product malfunctions that cannot be resolved through troubleshooting, please contact the official after-sales service. Unauthorized opening or repair of the device is strictly prohibited and may void any applicable warranty.

For a more detailed user guide and additional information, please refer to the official PDF manual available at: ZIBOO FT-1000W User Manual (PDF).

© ZIBOO. All rights reserved.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.