FGHGF Y45A

Contents

Y45A Vinyl Phono Amplifier Preamplifier Board User Manual

1. Introduction

This manual provides instructions for the FGHGF Y45A-Vinyl Phono Amplifier Preamplifier Board. This board is designed to enhance the audio quality of vinyl record players, specifically supporting MM (Moving Magnet) and MC (Moving Coil) cartridges. It incorporates JRC2150BBE sound effect processing for improved clarity, dynamic range, and adjustable treble/bass effects.

The circuit features a special amplifier chip for vinyl record players, a frequency compensation circuit for balanced sound, and a low-noise input signal filter. A rectifier filter voltage stabilizer circuit is also included for stable operation.

2. Safety & Warnings

Warning!

  • This product is intended for adult use only.
  • Keep out of reach of children and pets to prevent accidental injury or ingestion.
  • Always verify correct installation before operation.
  • If you observe abnormal noise or equipment malfunction after installation, immediately disconnect power and cease use.
  • Adhere strictly to all instructions for proper use; misuse can lead to harm.
  • Store the product in a dry, shaded environment, away from high temperatures, excessive humidity, and direct sunlight.

This product is CE certified, indicating compliance with European health, safety, and environmental protection standards.

3. Package Contents

The standard package includes:

  • 1 x Y45A Vinyl Record Player Board Kit (Amplifying board)
  • 1 x Power Transformer
  • 2 x Lotus Sockets (RCA jacks) with 300mm shielded wire

Note: Other products shown in promotional images are not included unless explicitly listed above.

Overall view of the Y45A Phono Amplifier Preamplifier Board kit, including the main board, power transformer, and RCA input/output jacks.

Figure 1: Overall view of the Y45A Phono Amplifier Preamplifier Board kit, including the main board, power transformer, and RCA input/output jacks.

4. Setup Instructions

4.1 Initial Inspection

Before first use, ensure the product is free from any visible damage.

4.2 Power Connection

  • The working voltage for this board is AC dual 10-17V. Ensure your power supply matches this requirement.
  • The quality of the power supply significantly impacts the sound effect. Use a stable and good quality power supply.
  • Consider adding an AC filter to the 220V input terminal for improved performance and reduced interference.

4.3 Audio and Ground Connections

Carefully follow the connection diagram below for proper audio signal and grounding:

Detailed diagram of the Y45A amplifier board's input and output connections, indicating 'Phono signal input', 'Ground pad', and 'Output power amplifier board'.

Figure 2: Detailed wiring diagram for the Y45A amplifier board, showing Phono signal input, Ground pad, and Output power amplifier board connections.

  • Phono Signal Input: Connect your vinyl record player's audio output to the "IN" terminals (L and R) on the amplifier board.
  • Output to Power Amplifier: Connect the "OUT" terminals (L and R) of this preamplifier board to the input of your main power amplifier.
  • Grounding:
    1. The ground wire of your vinyl machine MUST be connected to the "GND" terminal at the power input end of the amplifier board.
    2. Alternatively, connect it to the "GND" ground pad located next to the phono input.
    3. If possible, connect the system's ground to the mains ground to minimize interference.

    Improper grounding can cause significant interference and negatively impact sound quality.

5. Operating Instructions

Once the Y45A Preamplifier Board is correctly installed and connected, it functions as an essential link between your vinyl turntable and your main amplifier. It amplifies the delicate phono signal and applies sound effect processing.

  1. Ensure all connections (power, input from turntable, output to amplifier, and ground) are secure.
  2. Power on your main amplifier, then the Y45A preamplifier board.
  3. Start playing a vinyl record on your turntable.
  4. Adjust the volume on your main amplifier to the desired listening level.
  5. The JRC2150BBE sound effect processing provides high and low sound effects, improving clarity and dynamic range automatically. No user-adjustable controls are present on the board itself for these effects.

6. Maintenance

6.1 Cleaning

To clean the board, ensure it is powered off and disconnected from all sources. Use a soft, dry cloth to gently wipe away dust. Do not use liquid cleaners or solvents, as these can damage electronic components.

6.2 Storage

When not in use for extended periods, store the preamplifier board in a dry, cool, and shaded place. Keep it away from extreme temperatures, humidity, and direct sunlight to prolong its lifespan. Always store it out of reach of children and pets.

7. Troubleshooting

Problem Possible Cause Solution
No sound or low volume. Incorrect connections, power supply issue, turntable not playing.
  • Check all audio input/output cables and power connections.
  • Ensure the power supply is within the AC dual 10-17V range and is stable.
  • Verify the turntable is operating correctly.
Humming or buzzing noise. Improper grounding, interference from power supply.
  • Ensure the vinyl machine's ground wire is securely connected to the amplifier board's GND terminal or ground pad.
  • If possible, connect to mains ground.
  • Consider adding an AC filter to the power input.
  • Check for loose connections.
Distorted sound. Poor power supply quality, incorrect input level.
  • Ensure a high-quality, stable power supply.
  • Verify the turntable output is compatible with MM/MC input.
Equipment error or abnormal behavior. Internal fault, incorrect component values.
  • Immediately disconnect power.
  • Contact customer support if the issue persists after checking connections and power.

8. Specifications

Feature Detail
Product Name Y45A-Vinyl Phono Amplifier Preamplifier Board
Chipset JRC2150BBE
Supported Cartridges MM (Moving Magnet), MC (Moving Coil)
Sound Effects Treble, Bass, Improved Clarity, Dynamic Effect
Working Voltage AC dual 10-17V
Board Size 85mm x 50mm
Overall Height Approx. 23mm
Material PC + Metal
Brand FGHGF
Maximum Power Per Channel NO POWER (This is a preamplifier, not a power amplifier)

9. User Tips

  • Optimal Grounding: Always ensure your vinyl machine's ground wire is properly connected to the amplifier board's GND terminal or ground pad. If possible, connect to mains ground to minimize hum and interference.
  • Stable Power Supply: The quality of your power supply directly affects the sound output. Invest in a stable and clean AC dual 10-17V power source for the best audio performance.
  • Reduce AC Noise: For even better sound clarity, consider adding an external AC filter to the 220V input terminal of your power supply.
  • Component Protection: Handle the board carefully. While the chip is polished, avoid unnecessary touching of components.

10. Manufacturer & Support Information

Manufacturer:

Nanchang sheyu electronic products co., ltd
Room 408, Building C, Ziyang Mingzhu Office Building
No.2999 Ziyang Avenue, Nanchang High-tech Industrial Development Zone
Nanchang City, Jiangxi Province Code: 330000, China

EU Authorized Representative:

Outong GmbH
Brehmstr, 56, 40239 Duesseldorf, Germany
Email: info@outong.de
Phone: +49 21131054698

Additional Resources:

A detailed user manual is available in PDF format. You can access it via the seller's product page or by searching for "Y45A Vinyl Phono Amplifier Preamplifier Board User Manual PDF" online. The direct link provided by the seller is: User Manual (PDF)

© 2024 FGHGF. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.