1. Product Introduction
Welcome to the INSE N3T Cordless Vacuum Cleaner user manual. This guide provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your new appliance. We are always here for you if you need assistance.
Product Components
The INSE N3T Cordless Vacuum Cleaner comes with the following parts:

Diagram showing all components included with the INSE N3T Cordless Vacuum Cleaner, labeled 1 through 10.
| No. | Part Name | Quantity |
|---|---|---|
| 1 | Main Motor | 1 |
| 2 | Metal Connecting Tube | 1 |
| 3 | Motorized Brush (Floor Brush) | 1 |
| 4 | 2-in-1 Brush | 1 |
| 5 | Replaceable Filter Cotton | 1 |
| 6 | Wall Bracket | 1 |
| 7 | Adapter | 1 |
| 8 | 2-in-1 Cleaning Gadget | 1 |
| 9 | User Manual | 1 |
| 10 | User Guide | 1 |
Official product video demonstrating the features and usage of the INSE N3T Cordless Vacuum Cleaner.
2. Setup and Charging
Wall Mount Installation
Choose a location close to a power outlet. The point should be high enough on the wall to allow the telescopic wand and floor nozzle to hang freely. Place the wall mount against the wall and use a pencil to mark the drill holes. Drill holes (with a 1/4" bit) and insert drywall anchors. Insert screws through the holes on the mount and tighten until firmly attached.

Image showing the main vacuum unit, various accessories including the wall mount, and the US flag indicating shipping from the United States.
Assembly
- Connect the Metal Tube: Slide the telescopic tube onto the main motor until it clicks.
- Attach the Floor Brush: Push the telescopic tube into the floor brush until it clicks.
- Attach Accessories: For cleaning high positions, accessories can be connected directly to the metal tube.
Charging
The battery must be fully charged before the first usage as the product is delivered uncharged.
Method 1: Wall-Mounted Charging
Place the main motor onto the wall bracket for charging.
Method 2: Flat Surface Charging
Place the main motor on a flat surface when recharging.
Connect the adapter to the main motor's charging port. The power indicator will flicker during charging.
Tip: In case of dropping, the appliance should be charged horizontally, without the brush and extension tube attached.
Charging Time: General charging time is 4-5 hours.
3. Operating Instructions
Power On/Off
Press the power button once to turn the vacuum cleaner on. Press it again to turn it off.
Cleaning Modes
Press the 'MAX' button to switch between intense cleaning mode and energy-saving suction mode, according to your cleaning needs.
Floor Cleaning
The INSE N3T is designed for powerful cleaning on both carpet and hard floors, effectively picking up dust, hair, coffee beans, and other debris.

Demonstration of the vacuum cleaner's effectiveness on various floor types, showing it picking up dust, hair, coffee beans, and crumbs.
Flexible LED Motorized Head
The motorized brush head features 4 LED lights to illuminate dust in dark areas, ensuring no dirt is missed. Its flexible design allows for easy maneuverability.

Diagram illustrating the flexible movement of the motorized brush head, showing $90^{\circ}$ vertical rotation and $155^{\circ}$ horizontal rotation for cleaning under furniture and in tight spaces.
- LED Lights: With 4 LED Lights, dust on the ground has nowhere to hide.
- Rotation: The brush head supports $90^{\circ}$ vertical rotation and $155^{\circ}$ horizontal rotation, making it easy to clean around corners and under furniture.
Multi-function Use (3-in-1)
The INSE N3T can be configured in multiple ways to suit various cleaning tasks, transforming from a stick vacuum to a handheld unit with different attachments.

Examples of the vacuum cleaner being used in different configurations (stick, handheld, extended) for various cleaning tasks around a living room.
- Stick Vacuum: For floors and carpets.
- Handheld Vacuum: For furniture, car interiors, and stairs.
- Extended Handheld: With the metal tube and 2-in-1 brush for high-up areas like curtains and shelves.
4. Maintenance
To ensure maximum performance and longevity of your vacuum cleaner, regular maintenance of its components is strongly recommended.
Daily Maintenance
- Clean Non-electricity Part of the Main Motor: Turn off the vacuum before cleaning. Wipe the surface with a clean cloth, being cautious not to get water into the inner part of the main motor.
- Storage: Do not place the vacuum cleaner under direct sunlight or in wet places after cleaning.
Clean Detachable Roller Brush
If the roller brush gets tangled or stuck, an alert will appear on the LED display. Clean it promptly.
- Unlock the side lock on the bottom side of the cleaner head.
- Remove the side cover and take out the roller brush.
- Use the 2-in-1 Cleaning Gadget to remove tangled hair and debris.
Clean Plastic Filter Screen & Filter
IMPORTANT:
- Please check and clean the Plastic filter screen & Filter regularly.
- Clean the filter in time if the suction performance declines.
- Replace the filter if it is broken or cannot maintain the suction performance.
- Do not bend or squeeze the filter.

Diagram illustrating the Advanced Cyclonic Filtration System components: High Density Sponge, Cyclone Filtration, High Efficient Filter Pad, Honeycomb Filter, and First Cyclone.
- Detach the main motor and dust cup. Take out the filter from the main motor and the filter component from the dust cup. Hold the strainer, rotate the filter holder, then take out the filter.
- If they are too dirty, wash the strainer and the sponge with cool water, and clean the filter with the cleaning brush.
- Ensure the Plastic filter screen & Filter are completely dry before refitting.
- Do not charge if the ambient temperature is lower than $5^{\circ}C$ or higher than $40^{\circ}C$.
- If the power indicator flickers due to insufficient power during operation, recharge the unit.
Appliance Cleaning (Dustbin Emptying)
Regularly empty the dust box to ensure constant suction.
- Hold the cleaner over a waste basket.
- Press the lever to release the bottom lid of the dust cup to empty its contents.
- Remove the dust cup by twisting to the 'unlock' position. Empty its contents, then reattach the dust cup and twist to 'lock' position.
- Twist the dust cup and remove the filter screen. Lift out the foam filter. Rinse and dry all components thoroughly. Reassemble after each part has dried completely.
Caution:
- Pay attention to sharp objects such as glass to prevent injury.
- Do not wash the mechanical part of the dust box.
- Ensure each part is completely dry before next usage.
- Do not scrub the filter or apply undue force.
- Ensure the filter is correctly secured during assembly.
- Change the filter if damaged or if cleaning does not return it to its pristine state.
5. Troubleshooting
If you encounter any issues with your INSE N3T Cordless Vacuum Cleaner, please refer to the table below for solutions.
Q1. Running time shortened
| Problem | Solution |
|---|---|
| Battery life has decreased. | Contact support for battery replacement. |
| Ambient temperature is too high or too low. | Operate in a suitable ambient temperature. |
| Battery is not fully charged. | Charge the battery fully. |
Q2. The vacuum has no suction power
| Problem | Solution |
|---|---|
| Dust cup is full. | Clean the dust cup after each use. |
| Filter is blocked. | Remove any dust or debris from the filter. |
| Accessory is blocked. | Check for blockages in the brush and other attachment points. |
| Suction inlet of brush or other part is blocked. | Clear any obstructions. |
| Parts of the appliance are not fully dried after cleaning. | Ensure all components are properly dried after washing. |
Q3. No charging
| Problem | Solution |
|---|---|
| Ambient temperature when charging is too low or too high. | Charge the machine under the right temperature environment ($5^{\circ}C-40^{\circ}C$). |
6. Specifications
| Parameter | Value |
|---|---|
| Product Category | N3K, N3X, N3E, N3P, N3T |
| Net Weight | 1.1KG |
| Total Weight (All Accessories Included) | 1.8KG |
| Nominal Voltage | 18V |
| Nominal Power | 180W |
| Adapter Input | 100V-240V ~ 50/60Hz |
| Battery Capacity | 2000 mAh |
| Adapter Output | 22V |
| Retractable Tube Length | 47 / 77cm |
| Product Dimensions | 43.5*28.5*18.0cm |
| Weight (Product) | 3 - 6 KG |
| Number of Nozzles | 1-3 nozzles |
| Number of Operating Modes | 1-2 |
| Battery Type | Li-ion |
| Liquid Tank Volume | <3l |
| Dust Box Capacity | 0.6-1 L |
| Filter Type | HEPA |
| Cord Length | Wireless |
| Special Suction Nozzle | Flat Suction Nozzle |
| Dust Storage Type | Dust Box |
| Installation | Hand Held |
| Certification | CE |
| Function | Dry |
| Battery Life | 40 minutes |
7. User Tips
No specific user tips were available from the provided data.
8. Warranty and Support
NOTE: This warranty term gives you specific legal rights, and you may also have other rights which vary from state to state.
24-month Warranty & Lifetime Customer Support
This warranty applies only to eligible purchases made directly from authorized distributors. Warranty coverage applies to the original owner and to the original product only and is not transferable.
How to Initiate a Warranty Claim
If your appliance operates improperly while in use under normal household conditions within the warranty period, please contact our customer support at support@vacservice.vip to fill out the warranty form and initiate a warranty claim.
For a detailed user manual with multilingual options, you can also refer to the official PDF document: User Manual (PDF).