1. Product Introduction & Specifications
1.1. Technical Parameters
| Parameter | Specification |
|---|---|
| Batteries | 4xAA (Sold Separately) |
| Working Temperature | -30°C ~ 70°C (Not Condensation) |
| Door Thickness | 35mm ~ 50mm (1-3/8" to 2") |
| Material | Aluminum Alloy |
| Unlock Mechanism | Key / PIN |
| PIN Groups | 100 Groups |
| Relative Humidity | < 95% |
1.2. Functional Components
The DESLOC C100 lock consists of an exterior lock and an interior lock, each with distinct functional components:
Exterior Lock
The exterior unit features a display screen, a numeric keypad, a traditional keyhole, and a Type-C port for emergency power backup.
Interior Lock
The interior unit includes a battery cover and a knob for manual operation.
2. Installation Instructions
For a visual guide, please watch the official installation video:
Official installation guide for the DESLOC C100 Keypad Digital Deadbolt.
2.1. Package Contents
Before starting the installation, ensure all components are present:
- Exterior Lock
- Interior Lock
- Mounting Plate
- Strike Plate
- Deadbolt
- Mechanical Keys (2)
- Deadbolt/Strike Plate Screws
- Mounting Plate Screws
- Interior Lock Screws
Refer to the "What's included for installation" diagram on page 6 of the PDF manual for a visual representation of these components.
2.2. Pre-Installation Steps
-
Measure the Door Size:
Verify your door's dimensions for compatibility:
- Door Thickness: 1-3/8" to 2" (35mm to 50mm)
- Hole Diameter: 2-1/8" (54mm)
- Backset: 2-3/8" or 2-3/4" (60mm or 70mm)
Ensure your door meets these specifications for proper installation.
-
Adjust the Length of the Deadbolt:
If your door's backset is 70mm, turn the deadbolt's faceplate 180° to extend its length. The deadbolt should be in the unlock position and the paddle in a horizontal status before proceeding.
2.3. Installation Procedure
-
Install Deadbolt:
Insert the deadbolt into the door edge. Ensure the word "UP" on the deadbolt is facing upwards. Secure it with the provided deadbolt screws. Keep the deadbolt retracted during this step.
-
Install Exterior Lock:
Route the cable from the exterior lock below the deadbolt. The paddle on the exterior lock must be in a horizontal position. Do not insert the mechanical key during this step.
-
Fix the Mounting Plate:
Peel off the adhesive tape from the mounting plate. Thread the exterior lock's cable through the hole in the mounting plate. Secure the mounting plate to the door with the mounting plate screws.
-
Install the Interior Lock:
Connect the cable from the exterior lock to the interior lock securely. Turn the doorknob on the interior lock horizontally and insert the paddle into the deadbolt mechanism. Ensure excess cables are neatly tucked into the door's cable housing area. Do not install batteries yet.
-
Fix the Interior Lock:
Open the battery cover of the interior lock. Secure the interior lock to the mounting plate using the interior lock screws. Rotate the doorknob to test if the deadbolt extends and retracts smoothly.
-
Install Batteries:
Insert 4xAA batteries (sold separately) into the interior lock's battery compartment, observing the correct polarity (+/-). Close the battery cover.
For detailed diagrams of each installation step, please refer to pages 7-11 of the PDF user manual.
3. Operating Instructions
3.1. Product Button Description
The lock features a numeric keypad and specific function buttons:
- Number Buttons (0-9): Used to enter PINs, numbers, and names. These buttons also function for letter input (e.g., pressing '2' once for '2', twice for 'A', three times for 'B', four times for 'C').
- [MENU] Button: Enters the settings interface, acts as a backspace to delete incorrect text, and returns to the previous menu.
- [ENTER] Button (Lock Icon): Confirms current operations. Double-click to confirm after input is complete. Press to lock the door.
- Up Arrow (7/PORS): Scrolls menu items up.
- Down Arrow (9/WXYZ): Scrolls menu items down.
Refer to the "Product button Description" diagram on page 13 of the PDF manual for a visual guide to button functions.
3.2. Initial Setup and PIN Management
-
Change Initial PIN:
The initial management PIN is 123456. It is crucial to change this immediately after installation.
- Press [MENU].
- Enter "123456" and press [ENTER].
- The lock will automatically detect the door's opening direction (keep the door open and avoid operations).
- Enter the administrator's name (e.g., "Ab" by pressing '2' twice for 'A', then [ENTER], then '2' three times for 'b', then double-click [ENTER]).
- Enter a new 6-8 digit PIN and press [ENTER].
- Re-enter the new PIN to confirm and press [ENTER].
-
Add Admin PIN:
To add additional administrators:
- Press [MENU] > "Add Admin" > "Add Admin PIN".
- If adding to an existing admin, select the admin (e.g., "Ab") and press [ENTER].
- Enter a new 6-8 digit PIN and press [ENTER].
- Re-enter the new PIN to confirm and press [ENTER].
- If adding a new admin, select the new administrator's name and press [ENTER].
- Enter a new 6-8 digit PIN and press [ENTER].
- Re-enter the new PIN to confirm and press [ENTER].
-
Add User PIN:
To add regular users:
- Press [MENU] > "Add User" > "Add User PIN".
- Enter the new user's name and press [ENTER].
- Enter a new 6-8 digit PIN and press [ENTER].
- Re-enter the new PIN to confirm and press [ENTER].
- Alternatively, select an existing user (e.g., "Andy") and follow the same steps to set their PIN.
-
Add Temporary PIN:
Temporary PINs are single-use and expire after one use. They are valid for 30 seconds on the screen.
- Press [MENU] > "Add User" > "Add Temp PIN".
- Press [ENTER] to generate 4 sets of temporary PINs.
- Note: Take a photo of the screen as the PINs flash quickly and are only displayed for 30 seconds.
-
Delete User:
You can delete individual users (administrators or regular users), but not the primary administrator.
- Press [MENU] > "Del User" > "Del User".
- Select the user name to delete (e.g., "Andy") and press [ENTER]. All information for that user will be deleted.
To delete all regular users:
- Press [MENU] > "Del User" > "Del All User" > "YES".
- Press [ENTER] to delete all user information.
-
Delete Temporary PIN:
To delete temporary PINs:
- Press [MENU] > "Del User" > "Del Temp PIN".
- Press [ENTER] to delete all temporary PINs.
- Note: If temporary PINs were issued but not used, it's recommended to delete them or regenerate new ones.
3.3. Lock Settings
-
Open Direction:
This setting allows the lock to adapt to your door's opening direction.
- Press [MENU] > "Lock Settings" > "Open Direction".
- Select "Left Open" or "Right Open" based on your door and press [ENTER].
-
Passage Mode:
When enabled, the door lock will remain unlocked and will not auto-lock.
- Enable: Press [MENU] > "Lock Settings" > "Lock Setup" > "Passage Mode". Select "ON" and press [ENTER].
- Quick Enable: After unlocking, enter '5' on the keypad within 2 seconds. The screen will display "Passage Mode".
- Exit: Press [MENU] > "Lock Settings" > "Lock Setup" > "Passage Mode". Select "OFF" and press [ENTER]. Alternatively, after unlocking, enter '5' on the keypad within 2 seconds.
Passage mode keeps the lock cylinder retracted, allowing free entry and exit.
-
Auto Lock:
Sets the time period after which the lock automatically engages.
- Press [MENU] > "Lock Settings" > "Lock Setup" > "Auto Lock".
- Press [ENTER] to select, then enter a time period (5-120 seconds) and press [ENTER] to confirm.
-
Sound Setup:
Enables or disables the lock's sound prompts.
- Press [MENU] > "Lock Settings" > "Sound Setup".
- Select "Sound ON" or "Sound OFF" and press [ENTER].
-
Factory Reset:
Resets the lock to its default factory settings, erasing all user data and reverting the Master PIN to 123456.
- Method 1 (Via Menu): Press [MENU] > "Lock Settings" > "Factory Reset" > "YES". Press [ENTER] to confirm.
- Method 2 (Physical Button): Slide up the battery cover on the interior lock. Press and hold the Reset button. Select "YES" on the front lock and press [ENTER] to confirm.
- Important: After a factory reset, immediately change the initial administrator PIN. The lock will automatically adapt to the door opening direction upon battery reinstallation or initial PIN change.
4. Maintenance
- Battery Life: The lock is designed for approximately 1 year of battery life. Replace batteries promptly when low battery warnings appear.
- Emergency Power: In case of complete battery depletion, the lock can be opened using a mechanical key or by connecting an external mobile power supply to the Type-C backup power port for emergency charging.
- Cleaning: Use a soft, dry cloth to clean the keypad and display screen. Avoid abrasive cleaners or solvents.
- Environmental Conditions: The lock is designed to operate in temperatures from -30°C to 70°C and relative humidity below 95% (non-condensing). Avoid exposing the lock to extreme conditions outside this range.
The lock is built for durability in various weather conditions, featuring a 1-year battery life and emergency charging capabilities.
5. Troubleshooting
5.1. Warning Icons and Their Meanings
| Warning Icon | State Description |
|---|---|
| Failed Check Deadbolt | Indicates that the lock is not properly closed or opened. Check the lock status or battery level. |
| Low Battery (Level 1) | Level 1 low battery alarm. Replace the batteries immediately. |
| Low Battery (Level 2) Inoperable | Level 2 low battery alarm; be sure to replace batteries. If power runs out, use a mechanical key or emergency power. |
| Passage Mode Active | Indicates that Passage Mode is currently active. |
5.2. Common Issues and Solutions
-
Lock not responding / No power:
Check battery installation and ensure batteries are fresh. If batteries are completely drained, use the mechanical key or connect an external power bank via the Type-C port for emergency power.
-
Deadbolt not extending/retracting smoothly:
Ensure the deadbolt was installed correctly and is not obstructed. Verify the door measurements and deadbolt adjustment (Section 2.2). Check for any loose screws or misalignments.
-
PIN not working:
Ensure the correct PIN is being entered. Check if the lock is in Passage Mode. If it's a new installation, ensure the initial PIN (123456) has been changed and new administrator/user PINs are correctly set. Consider performing a factory reset if all else fails, then reconfigure all settings.
-
Lock not auto-locking:
Check if Passage Mode is active (indicated by the icon). If so, disable it. Verify the Auto Lock setting is configured with a desired time period.
-
Duplicate PIN error:
The system prevents PINs that are subsets or supersets of existing PINs. For example, if "147258" exists, "14725836" is a duplicate. If "14725836" exists, "147258" is a duplicate. Choose a unique PIN.
-
Screen flashes quickly when generating temporary PINs:
This is normal behavior. It is recommended to take multiple photos of the screen to capture all temporary PINs within the 30-second display window.
6. User Tips
- Regular Battery Checks: Even with a 1-year battery life, it's good practice to check battery levels periodically, especially before extended absences.
- Keep Mechanical Keys Handy: Always store your mechanical backup keys in a safe, accessible location outside your home for emergency access.
- Utilize Scramble PIN: When entering your PIN in front of others, use the Scramble PIN feature by entering random digits before or after your actual PIN to prevent shoulder surfing.
- Passage Mode for Convenience: Use Passage Mode when you expect frequent entry and exit (e.g., during a party or moving furniture) to avoid repeated unlocking. Remember to disable it afterward for security.
- Secure PIN Storage: Avoid writing down PINs in easily discoverable places. Memorize them or use a secure password manager.
- Door Alignment: Ensure your door is properly aligned and closes smoothly. Misalignment can cause the deadbolt to jam or prevent proper locking.
7. Warranty & Support
For further assistance or warranty claims, please contact DESLOC support:
- Website: www.desloc.com
- Email: support@desloc.com
- Phone: +1 (888) 572 6136
- Warranty: 12-month warranty
A PDF version of this user manual is available for download. You can find it at: DESLOC C100 User Manual (PDF)