Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your JMQWE AHD CVBS Car Rear View Camera. This camera is designed to enhance your vehicle's safety by providing a clear view of the area behind your car, especially useful for parking and reversing maneuvers. It features night vision capabilities and a waterproof design for reliable performance in various conditions.
For additional information and documents, please refer to the official user manual PDF: User Manual (PDF).
Product Overview
Front view of the camera with RCA and power cables.
Rear view of the camera, highlighting mounting points.
Camera dimensions: 30mm (length) x 22mm (width) x 22mm (height).
Installation Guide
Proper installation is crucial for optimal performance. Please follow these steps carefully.
1. Pre-Installation Checks
- Monitor Compatibility: Ensure your monitor is suitable for CVBS cameras (4.3-inch, 5-inch, 7-inch, 9-inch monitors, old-style navigation DVDs, and other monitors with CVBS function).
- Monitor Settings: Before installing, confirm your monitor's channel is set to CVBS/NTSC. Navigate to Car Setting >> Factory Setting >> Reverse (Picture) Setting >> Select CVBS NTSC.
- Parking Line: If you do not wish to have parking lines displayed, you can cut the white cable on the camera's wiring.
2. Wiring Diagram
The following diagram illustrates the wiring for both common (wired) and wireless camera setups.
Detailed wiring diagram for the camera, including connections for monitor, reversing light, and power for both wired and wireless configurations.
3. Wired Installation (Common Set / Power Relay Set)
- Connect Camera Power:
- Connect the camera's red power wire to the positive (+) terminal of your car's reversing light.
- Connect the camera's black power wire to a suitable ground point (GND) on your car chassis.
- Connect Video Signal:
- Connect the yellow RCA video cable from the camera to the video input (usually yellow RCA) on your car monitor.
- For the Power Relay Set, ensure the red wire on the video cable (trigger wire) is connected to the reversing light positive (+) at both ends (near the camera and near the monitor) to signal the monitor to switch to the camera input when reversing.
- Monitor Connection:
- Connect the monitor's red wire to ACC (Accessory power).
- Connect the monitor's black wire to GND (Ground).
- Connect the monitor's blue wire to the reverse detection line (trigger wire from the video cable, connected to reversing light positive).
4. Wireless Installation (Wireless Set)
- Connect Wireless Transmitter:
- Connect the wireless transmitter's red wire to the Backup Light Power 12V+.
- Connect the wireless transmitter's black wire to the Backup Light Power 12V-.
- Connect the camera's video output to the wireless transmitter's video input.
- Connect the camera's power input to the wireless transmitter's power output.
- Connect Wireless Receiver:
- Connect the wireless receiver's red wire to ACC 12V+.
- Connect the wireless receiver's black wire to GND.
- Connect the wireless receiver's video output to your car monitor's video input.
Operation
Once installed, the camera operates automatically when your vehicle is put into reverse gear.
- Automatic Activation: When you shift your vehicle into reverse, the camera will automatically power on and transmit video to your connected monitor. The monitor should switch to the camera's feed.
- Viewing Angle: The camera provides a wide viewing angle of 170° (or 155° as shown in some diagrams) to give you a comprehensive view of the area behind your vehicle, minimizing blind spots.
- Night Vision: The camera is equipped with night vision capabilities, allowing for clear visibility even in low-light conditions.
- Parking Lines: If the parking line feature is enabled (white cable not cut), static guiding lines will appear on the screen to assist with parking.
The camera offers a wide viewing angle for enhanced visibility.
Maintenance
To ensure the longevity and optimal performance of your rear view camera, follow these simple maintenance guidelines:
- Cleaning the Lens: Regularly clean the camera lens with a soft, damp cloth to remove dirt, dust, or water spots that may obstruct the view. Avoid abrasive cleaners.
- Waterproof Design: The camera is designed to be waterproof, ensuring reliable operation in rain or car washes. However, avoid directing high-pressure water jets directly at the camera for extended periods.
- Cable Inspection: Periodically check all cables and connections for any signs of wear, damage, or loose connections. Secure any loose wiring.
The camera is designed with a waterproof casing for durability.
Troubleshooting
If you encounter issues with your camera, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No image/signal on monitor |
|
|
| Distorted or flickering image |
|
|
| Parking lines not appearing/disappearing |
|
|
Specifications
| Feature | Specification |
|---|---|
| Brand Name | JMQWE |
| Model | AHD CVBS Car Rear View Camera |
| Lens Material | Plastic + Glass |
| Shell Material | Plastic |
| Material | ABS |
| Guiding Line | Yes (can be disabled by cutting white cable) |
| Viewing Angle | 170° |
| Wire or Wireless | Wire, Wireless (depending on selected set) |
| Length of Video Cable | 2m, 6m (depending on selected set) |
| Alarm Type | Vehicle Backup Cameras |
| Certification | CE, EAC, FCC, RoHS, KC |
| Origin | Mainland China |
| Camera Dimensions (approx.) | 30mm (L) x 22mm (W) x 22mm (H) |
| Package Weight (approx.) | 0.3 kg |
| Package Dimensions (approx.) | 11cm (L) x 6cm (W) x 6cm (H) |
User Tips
- Always test the camera and monitor connection before fully reassembling your vehicle's interior panels.
- When routing cables, ensure they are secured and away from moving parts or heat sources to prevent damage.
- For vehicles with complex electrical systems, consider consulting a professional for installation to avoid potential issues.
Warranty and Support
For any technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact the seller directly through the platform where you purchased the product.
Please retain your proof of purchase for warranty claims.