ONWA KS-200A+

Contents

ONWA KS-200A+ AIS Transponder User Manual

Model: KS-200A+

1. Introduction

This manual provides essential information for the installation, operation, and maintenance of your ONWA KS-200A+ Class B AIS Transponder. The KS-200A+ is a marine Automatic Identification System (AIS) transponder designed to transmit and receive AIS data, enhancing navigational safety by allowing your vessel to be seen by and to see other AIS-equipped vessels. This model supports NMEA2000 connectivity and features Wi-Fi capabilities.

This manual applies to KS200A+, KS200A+_SART, KS200B+ and KS200B+_N series devices.

Video: ONWA KS-200A+ AIS Transponder product overview.

2. Package Contents

Please verify that all items listed below are included in your package:

  • ONWA KS-200A+ Class B AIS Transponder Unit
  • Power/Data Cable
  • Mounting Screws
  • Fuses
  • Quick Start Manual (this document)
  • (Optional) GPS Antenna
ONWA KS-200A+ AIS Transponder and included accessories

Image: ONWA KS-200A+ AIS Transponder and included accessories.

3. Device Overview

Front Panel

Close-up view of the ONWA KS-200A+ front panel with indicators and power switch

Image: Close-up view of the ONWA KS-200A+ front panel.

The front panel features LED indicators and a power switch:

  • RX (Receiver Indicator): Indicates AIS signal reception.
  • TX (Transmitter Indicator): Indicates AIS signal transmission.
  • GPS (GPS Indicator): Indicates GPS positioning status.
  • POWER (Power Indicator): Indicates the device's power status.
  • ON/OFF Switch: To power the device on or off.
  • PWR/DATA Port: For power supply and data connection.
  • AIS SART Button (KS200A+_SART only): Used to send distress signals in emergencies.

Rear Panel Connectors

Side view of the ONWA KS-200A+ showing AIS, GPS, and NMEA2000 connectors

Image: Side view of the ONWA KS-200A+ showing connectors.

  • AIS Antenna Connector (PL259 female): For connecting the VHF antenna.
  • GPS Antenna Connector (SMA female): For connecting the GPS antenna.
  • NMEA 2000 Interface: For connecting to an NMEA 2000 network.
  • Ethernet Interface (KS200B+_N only): For network connection.

4. Installation

Proper installation is crucial for optimal performance. Follow these steps carefully:

Mounting

Secure the transponder unit in a suitable location using the provided mounting screws. Ensure it is in a dry, protected area, away from direct sunlight and excessive heat. Allow for adequate ventilation.

Wiring and Connections

Refer to the interconnection diagrams for correct wiring. The device requires a power supply of 10.5-35VDC.

Interconnection diagram for KS200A, showing power, data, VHF, and GPS antenna connections

Image: KS200A Connection Diagram (Power, Data, VHF, GPS Antenna).

Detailed interconnection diagram for KS200A+ and KS200A+_SART+, including NMEA 2000 and Ethernet (for KS200B+_N)

Image: Detailed Interconnection Diagram for KS200A+ and KS200A+_SART+ (including NMEA 2000).

  • Connect the Red wire (+) and Black wire (-) from the power/data cable to your vessel's 10.5-35VDC power supply.
  • Connect the VHF antenna to the AIS antenna connector.
  • Connect the GPS antenna to the GPS antenna connector.
  • For NMEA 2000 connectivity, connect the NMEA 2000 connector to your vessel's NMEA 2000 network.
  • For KS200B+_N models, connect an Ethernet cable to the Ethernet interface for network integration.

5. Operation

Powering On/Off

  • Turning Power ON: Press the [ON/OFF] switch on the rear panel to the ON position.
  • Turning Power OFF: Press the [ON/OFF] switch on the rear panel to the OFF position.

Indicator Lights

Monitor the LED indicators on the front panel for device status:

Indicator Light Status Description
POWER Red, continuously lit The device is turned on.
GPS Orange, blinking GPS positioning is unavailable.
GPS Green, continuously lit GPS positioning is successful.
TX Red, blinking Transmits a light that flashes when a signal is emitted. The reporting interval is: Dynamic Ship Data (Boat speed <2kn): 3 minutes; Dynamic Ship Data (Boat speed >2kn): 30 seconds; Static vessel data (similar to Category A): 6 minutes.
RX Green, blinking The indicator light flashes green when an AIS signal is received.

AIS SART Button (KS200A+_SART only)

The AIS SART button is for emergency use only to send distress signals. When pressed, the device will send an AIS SART message, which can be received by all AIS devices. Once the danger has passed, press the SART button again to restore the normal state.

Reset Hotspot

After successfully resetting the hotspot, GPS lights will go off for five seconds and then return to normal after five seconds.

6. Specifications

The following table details the technical specifications of the ONWA KS-200A+ AIS Transponder:

Detailed technical specifications table for the KS-200A+

Image: Technical Specifications.

Category Specification Value
Connectors GPS Receiver (AIS Internal) IEC 61108-1 compliant
VHF Antenna connector PL259 female
GPS Antenna connector SMA female
NMEA 2000 Interface Yes
Physical Dimension (L x W x H) 200mm x 102mm x 45.8mm
Weight 0.45kg
Battery Included No
Power Input 10.5~35VDC
Power Consumption 0.20A nominal
Electrical Interface RS232 38,400 baudrate bi-directional
Environmental Operating Temperature -25°C to +60°C (IEC 60945 Cat C)
NMEA Sentence Supported VDM, VDO, RMC, GSV, GGA, GSA
AIS Characteristics Frequency Rate 161.975 MHz, 162.025 MHz
Access Scheme SOTDMA
Channel Bandwidth 25KHz
Modulation AIS GMSK
Number of AIS Transmitter 1
Number of AIS Receiver 2
Standard TX Power Output 5W
Customizable TX Power Output 2W, 12.5W
RX Sensitivity < -120dBm @ 20% PER
RX Message Format AIS Class A and B messages
Comply Standard IEC-62287 IEC 62287-2 Ed. 2.0:2017

Note: All specifications are subject to change without further notice.

7. User Tips

  • Antenna Placement: Ensure your VHF and GPS antennas are installed with a clear line of sight and away from obstructions for optimal signal transmission and reception.
  • Power Supply: Always connect the device to a stable 10.5-35VDC power source to prevent operational issues.
  • Software Updates: Periodically check the manufacturer's website for firmware updates to ensure your transponder has the latest features and performance enhancements.
  • Local Regulations: Be aware of and comply with local maritime regulations regarding AIS transponder usage and any potential import duties or taxes on electronic equipment.

8. Troubleshooting

If you encounter issues with your ONWA KS-200A+ AIS Transponder, consider the following:

  • No Power: Check the power cable connection and the vessel's power supply. Ensure the ON/OFF switch is in the 'ON' position. Verify the fuse is intact.
  • No GPS Signal (Orange GPS LED blinking): Ensure the GPS antenna is properly connected and has an unobstructed view of the sky. Move the vessel to an open area if necessary.
  • No AIS Transmission (TX LED not blinking): Check all antenna connections. Ensure the device is receiving a valid GPS fix.
  • No AIS Reception (RX LED not blinking): Verify the VHF antenna connection. Ensure other AIS-equipped vessels are within range.
  • Data Connectivity Issues: Check the data cable connections (NMEA2000, RS232, or Ethernet for relevant models). Ensure your chartplotter or PC is configured correctly to receive AIS data.

For persistent issues, refer to the full user manual or contact ONWA customer support.

9. Maintenance

To ensure the longevity and optimal performance of your AIS Transponder:

  • Cleaning: Regularly wipe the unit with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners.
  • Connections: Periodically check all cable connections for corrosion or damage. Ensure they are securely fastened.
  • Environmental Protection: While designed for marine environments, protect the unit from extreme temperatures, direct prolonged sunlight, and excessive moisture when possible.

10. Warranty and Support

For detailed warranty information, technical support, and to download the full user manual, please visit the official ONWA Marine Electronics website:

http://www.onwamarine.com

Please consider the environment before printing the manual.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.