1. Introduction
This manual provides instructions for the Nice Flor Garage Door Remote Control, a rolling code transmitter operating at 433.92MHz. It is designed for use with compatible Nice garage door openers and gate systems. Please read this manual carefully before use to ensure proper operation and safety.
Video: Overview of the Nice Flor Remote Control.
2. Safety & Warnings
- WARNING: To avoid danger of suffocation, keep the plastic bag away from babies and children. Do not use this bag in cribs, beds, carriages, or play pens. This bag is not a toy.
- Keep the remote control out of reach of children.
- Do not expose the remote control to water or extreme temperatures.
- Ensure the garage door or gate is clear of obstructions before operating.
3. Specifications
| Feature | Specification |
|---|---|
| Product Name | Garage Door Remote Control |
| Model | RMTPS (Flor Flo2r-s series) |
| Encoding Method | Rolling code |
| Frequency | 433.92MHz |
| Dimensions (Approx.) | Length: 3.48cm (1.96in), Height: 7cm (2.75in) |
| Origin | Mainland China |
Image: Remote control dimensions and portability.
4. Compatible Models
This remote control is compatible with the following Nice Flor series models:
- SMXI / OXI / FLOX2R / FLOX4R / SMX2R / OX2 / OX4T
- FLO1RS, FLO2RS, FLO4RS, ON1, ON2, ON4, ON1E, ON2E, ON4E
- FLO1RE, FLO2RE, FLO4RE, Very VR, INITI (all colors)
- INTI1, INTI2, INTI1Y, INTI2Y, INTI1L, INTI2L, INTI1B, INTI1R, INTI2R, INTI1G, INTI2G, INTI2Y/A, INTI2/A, INTI2L/A, INTI2B/A, INTI2R/A, INTI2G/A
5. Setup (Programming Instructions)
To program your new remote control, follow these steps:
- Locate the 'Learn / Code Set' button on your garage door opener's motor unit. This button is typically found under the lamp cover or on the back of the motor.
- Press the 'Learn / Code Set' button once, then release it. A light on the motor unit should illuminate.
- Within a few seconds, press the desired button on your new remote control once. The light on the motor unit should go out.
- Press the same button on the remote control again. The light on the motor unit will flash and then go out, indicating that the remote has been successfully coded.
- Test the operation of the remote control by pressing the programmed button.
Image: Example location of the Receiver Button on a compatible circuit board.
6. Operating the Remote Control
Once programmed, simply press the corresponding button on your remote control to operate your garage door or gate. The remote transmits a rolling code signal, which enhances security by changing the code each time it's used.
Image: Examples of 2-button and 4-button remote controls.
7. Maintenance
- Battery Replacement: If the remote's range decreases or the indicator light does not illuminate, the battery may need replacement. Refer to the full user manual (PDF) for specific battery type and replacement instructions.
- Cleaning: Clean the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Storage: Store the remote in a dry place, away from direct sunlight and extreme temperatures.
8. Troubleshooting
- Remote not working after programming: Ensure you followed all programming steps correctly. The 'Learn / Code Set' button on your receiver might require a specific timing or sequence.
- Reduced range: Check the remote's battery. Replace if necessary. Ensure there are no new sources of interference (e.g., other wireless devices) near your garage door opener.
- Indicator light not illuminating: The battery may be depleted. Replace the battery.
9. User Tips
- Programming is generally straightforward, but always double-check your specific receiver's programming requirements, as they can vary slightly between models.
- These remotes are often identical in appearance and function to original Nice Flor-s remotes, making them a reliable replacement.
10. Warranty & Support
For detailed warranty information, technical support, or further instructions, please refer to the official user manual provided by the manufacturer. A comprehensive PDF manual is available for download:
Manufacturer Information:
Shenzhen ruimengda trading co., ltd
Address: Room 201e, building c6, hengfeng industrial city, no. 739 shishi road, hezhou community, hangcheng street, baoan district, shenzhen city, guangdong province, China.