BAOFENG UV-5RH PRO

Contents

Baofeng UV-5RH PRO GPS Walkie Talkie

User Manual

Preface

Thank you for choosing the Baofeng Multi-Band Amateur Radio. This radio utilizes advanced technology to provide reliable communications in demanding environments. It is extremely stable and reliable for long-distance communication with a sleek and compact design. Key features include emergency alarm, personnel death alarm, work alone, GPS, APRS position reporting, analog DTMF, 2TONE, 5TONE, CTCSS/DCS encode/decode.

Whether you are a professional needing to stay in touch with your team (e.g., ranching, farming, driving, hunting, forest protection, tactical training) or a recreational user, this product offers convenience for work, life, and leisure.

To avoid personal injury or property damage, please read all information carefully before use. To maximize convenience, read this manual and the Safety Information Manual.

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

ATTENTION!

When programming the radio, always start by reading the factory software data. Then, rewrite this data to a new saved code plug with your desired frequency settings. Failure to do so may result in errors. Use the programming cable with a PC to program authorized frequencies, bandwidth, power, etc. Your programming must comply with your FCC (or EU other country) license certification.

Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio. This guide contains instructions for safe usage and RF energy awareness and control to ensure compliance with applicable standards and regulations.

FRS, GMRS, MURS, PMR446: You may be tempted to use FRS, GMRS, MURS (in the USA) or PMR446 (in Europe) frequencies. Note that there are restrictions on these bands that make this transceiver illegal for use.

Safety Warnings

RF Exposure Compliance and Control

To control your exposure and ensure compliance with occupational/controlled environmental exposure limits, always adhere to the following procedures:

Guidelines:

  • Do not remove the RF Exposure Label from the device.
  • User awareness instructions should accompany the device when transferred to other users.
  • Do not use this device if the operational requirements described herein are not met.

Operating Instructions:

  • Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), press the Push-to-Talk (PTT) key. To receive calls, release the [PTT] key. Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy only when transmitting (in terms of measuring for standards compliance).
  • Keep the radio unit at least 2.5cm away from the face. Keeping the radio at the proper distance is important as RF exposure decreases with distance from the antenna. The antenna should be kept away from the face and eyes.
  • When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product. Use of non-approved accessories may result in exposure levels which exceed the FCC's occupational/controlled environmental RF exposure limits.
  • Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure guidelines.
  • Contact your local dealer for the product's optional accessories.

Precautions for Portable Terminals

Operating Prohibitions:

  1. Do not operate the product in a location containing fuels, chemicals, explosive atmospheres, and other flammable or explosive materials. In such locations, only an approved Ex-protection model is allowed for use, and any attempt to assemble or disassemble it is strictly prohibited.
  2. Do not operate the product near or in any blasting area.
  3. Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
  4. Do not hold the product while driving.
  5. Do not operate the product in any area where use of wireless communication equipment is completely prohibited.

Precautions for Batteries

Charging Prohibitions:

  1. Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres, and other flammable or explosive materials.
  2. Do not charge your battery that is wet. Please dry it with a soft and clean cloth prior to charging.
  3. Do not charge your battery suffering deformation, leakage, or overheating.
  4. Do not charge your battery with an unauthorized charger.
  5. Do not charge your battery in a location where strong radiation is present.
  6. Overcharge is prohibited as it may shorten the life of your battery.

WARNING!

When keys, ornamental chains, or other electric metals contact the battery terminal, the battery may become damaged or injure a human. If the battery terminals are short-circuited, it will generate a lot of heat. Take care when carrying and using the battery. Remember to put the battery or radio into an insulated container. Do not put it into a metal container.

Never store the battery in unsafe surroundings, as a short may cause an explosion.

Do not put the battery in a hot environment or throw it into a fire, as it may cause an explosion.

Setup

Package Contents

This transceiver comes shipped with the following items in the box:

  • 1 Radio body
  • 1 Lithium-Ion battery pack
  • 1 Instruction Manual
  • 1 Belt Clip
  • 1 Desk charger (With wall-wart)
  • 1 Antenna
  • 1 Wrist Belt

*If any item is missing, please notify your Baofeng / Pofung dealer.

Baofeng UV-5RH PRO walkie talkie with included accessories
Baofeng UV-5RH PRO walkie talkie with included accessories: antenna, battery, charger, belt clip, wrist strap, and user manual.

Battery Information

Charging the Battery Pack

The Li-ion battery pack is not charged at the factory; please charge it before use. For optimal performance, fully charge/discharge the battery two or three times before it reaches its best operating capacity. If operating time decreases after being fully charged, replace the battery pack.

Use only the specified charger provided by the company. Other models may cause explosion and personal injury. If the radio displays low battery with a voice prompt after installing the battery pack, please charge the battery.

How to Charge (using Desk Charger)

  1. Plug the AC adaptor into an AC outlet, then plug the cable of the AC adaptor into the DC jack on the back of the charger. The indicator light blinks orange, indicating it's ready to charge.
  2. Plug the battery or the radio into the charger. Ensure good contact between battery terminals and charging terminals. The indicator light turns red, indicating charging has begun.
  3. It takes approximately 2-5 hours to fully charge the battery. When the lamp lights green, charging is complete. Remove the battery or radio unit from the socket.

Note: When charging a radio (with battery) while powered on, the indicator lamp will not turn green to show fully charged status. The lamp will only indicate normal operation when the radio is switched off. The radio consumes energy when powered on, preventing the charger from detecting the correct battery voltage when fully charged. The charger will then charge in constant voltage mode and may not indicate correctly when the battery is fully charged.

LED Indicator Status:

STATUS LED
No Battery Green and red alternately flashing
Charge Normally Red
Fully Charged Green
Trouble Red blinks fast for a long time

NOTE: Trouble means battery too warm, battery short-circuited or charger short-circuited.

Using the Type-C USB Charger

The Type-C USB charger is a convenient way to charge your Li-ion battery pack.

  1. Make sure your radio is turned OFF.
  2. Plug the Type-C USB cable into the Type-C USB charging port on your battery. Connect the other end of the micro-USB charger to a wall power outlet.
  3. An empty battery will be fully charged in 4 hours.
  4. The battery meter on the LCD will move to indicate charging.

Note: It is recommended to power OFF your radio while charging. If powered on while charging, you may not be able to transmit a message if the battery is completely empty. Allow time for the battery to charge to 1 bar before attempting to transmit. For optimal battery life, remove the radio from the charger within 6 hours. Do not store the radio while connected to the charger.

How to Store the Battery

  • If the battery needs to be stored, keep it at 80% discharged.
  • Store in a low temperature and dry environment.
  • Keep it away from hot places and direct sunlight.
  • Do not short circuit the battery terminals.
  • Never attempt to remove the casing from the battery pack.

Accessory Installation

Before the radio is ready for use, you need to attach the battery pack and charge the battery.

Installing/Removing the Antenna

  1. Installing: Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
  2. Removing: Turn the antenna counter-clockwise to remove it.

Installing the Belt Clip

  1. At the back of the radio, there are two parallel screws mounted above the battery. Remove these and thread them through the holes on the belt clip as you screw them back into the radio body.
  2. Removing: Unscrew counter-clockwise to remove the belt clip.

Installing the Battery Pack

Before attaching or removing the battery, ensure your radio is turned off by turning the power/volume knob all the way counter-clockwise.

  1. Make sure the battery is aligned in parallel with the radio body with the lower edge of the battery about 1-2cm below the edge of the radio.
  2. Once aligned with the guide-rails, slide the battery upward until you hear a click as the battery locks in place.

To remove the battery: Press the battery release above the battery pack, as you slide the battery downward.

Installing the Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.

Diagram showing how to connect an external speaker/microphone to the walkie talkie
Wiring diagram for connecting an optional external speaker/microphone to the radio.

Radio Overview

Buttons and Controls

Diagram of Baofeng UV-5RH PRO radio with numbered parts
Front, side, and back views of the Baofeng UV-5RH PRO radio with numbered components.
  1. Power/Volume knob
  2. SK1- Broadcast FM and Alarm key
  3. PTT key
  4. VFO/MR mode key
  5. Status LED
  6. SK2-Flashlight and Monitor key
  7. A / B select key
  8. Key (MENU)
  9. Numeric keypad
  10. Antenna jack.
  11. LED flashlight
  12. Color LCD
  13. Accessory jack
  14. Speaker and microphone
  15. One-Touch search key
  16. Key (EXIT)
  17. or navigation keys
  18. Type-C charging port
  19. Type-C charging indicator
  20. Battery release latch

Main Keypad Controls

  • VFO/MR: Short press to switch VFO/MR mode. Press and hold to switch channel display mode: Channel CH, Frequency (display small channel number), Name (channel alias).
  • A/B: Short press to switch between A (upper) and B (lower) displays. Press and hold to switch Double Wait / Signal Wait / Off dual watch mode.
  • Sweep: Short press to enter one key sweep.
  • EXIT: Short press to return to the menu or previous menu. Press and hold to quickly enter GPS mode (My Location, valid when GPS function is turned on).
  • #: Press and hold to lock or unlock the keyboard. In transit mode, short press the key in inverted frequency (display R)/offline (display T).
  • DTMF: Short press to enter DTMF dial. Press and hold to scan on and off.
  • 0[space]: Press and hold to enter weather switch to select weather channel.

Programmed Key (SK1/SK2)

It is possible to set different functions for [SK1], [SK2] keys. This can be done via the radio Menu (Radio Setting - Press and Longpress SK1, SK2) or PC software (Buttons).

Option Functionality
NoneNo function is assigned to this button.
ScanTo enable or disable the Scan feature.
MonitorTo enable or disable the Monitor feature.
TouchTo enable or disable the Touch feature.
FM RadioTo enable or disable the FM Radio feature.
SOSTo enable or disable the emergency alarm feature.
GNSS systemTo enable or disable the GNSS system feature.
One Touch SearchTo enable or disable the One Touch Search feature.
1750HzTransmits 1750Hz Tone Burst
BTTo enable or disable the BT feature. The BT earpiece can work properly only after the BT feature is enabled.
Man DownTo enable or disable the Man Down feature.
One Touch CallTo make a call or send a message to the preset contact or implement an auxiliary feature.
ZoneTo Switch between the two zone.
VoltageCheck the current battery capacity voltage
TX PowerSwitch the power between super high, high, middle and low power.
VOXTo enable or disable the VOX feature.
Work AloneTurn on/off the work alone function.

Status Indications (Top LED)

LED Indication What it Indicates
Constant GreenReceiving Signal
Constant RedTransmitting signal
Flashes GreenMonitor mode/Scanning Receiving

LCD Icon Summary

LCD screen icons and their meanings
Overview of LCD screen icons, including VOX, Man Down, APO, FM Radio, Battery level, Current Zone, Watch Channel, Watch Frequency, A BAND RSSI, A Band, VFO Mode, Scan On, Operating Frequency, B Band, Transmit power, Keyboard locked, Bluetooth enabled, GPS enabled, NOAA enabled, NOAA Alerts Enabled, Signal Wait, Volume level, and Squelch level. The highlighted band is the main channel (working band) and the grayed-out band is the sub band (watch band).

Operating Instructions

Basic Operations

Power On/Off

  • Turning the unit on: Rotate the Volume/Power knob clockwise until you hear a "click". The radio should emit an audible double beep and display a frequency or channel. If Voice prompt is enabled, it will announce "frequency mode" or "channel mode".
  • Turning the unit off: Turn the Volume/Power knob counter-clockwise all the way until you hear a "click". The unit is now off.

Adjusting the Volume

To turn up the volume, turn the Volume/Power knob clockwise. To turn the volume down, turn the Volume/Power knob counter-clockwise. Be careful not to turn it too far, as you may inadvertently turn your radio off.

Main Band/Sub Band Switch

Press the [A/B] key to switch between A (upper) and B (lower) displays. The frequency or channel on the selected display becomes the active listening and transmit frequency or channel. The highlighted band is the main band and the grey band is the sub band.

VFO/Channel Switch

Pressing the [VFO/MR] key switches between Frequency (VFO) Mode and Memory (MR) mode. Memory mode is also referred to as Channel mode. Channel (MR) mode is generally more practical for everyday use, while Frequency (VFO) mode is useful for experimentation. Your choice of mode will depend on your use case.

Frequency (VFO) Mode

In Frequency (VFO) mode, you can navigate up and down the band using the ▲ or ▼ keys. Each press will increment or decrement your frequency according to the set frequency step. You can also input frequencies directly on your numeric keypad with kilohertz accuracy.

Example: Entering the frequency 436.61250 MHz on display A

  1. In standby mode, press and hold the [VFO/MR] key to switch to Frequency (VFO) mode.
  2. Enter [4][3][6][6][1][2][5][0] on the numeric keypad.

Channel (MR) Mode and Channel Selection

Pressing the [VFO/MR] key switches between Frequency (VFO) Mode and Memory (MR) mode. Select Channel mode.

  • Operation 1: Press the ▲ or ▼ navigation key to select the channel.
  • Operation 2: Input the channel numbers by the keyboard. For example, to switch to channel 12, input [1][2].

When the voice prompt function is enabled, the corresponding channel will be broadcast by voice.

Select a Zone

A zone is a group of channels with the same property. The radio supports up to 10 zones, with a maximum of 64 channels per zone. To select a zone:

Press the [MENU] key, go to Menu > Zone, press ▲ or ▼ to select a zone, and then press [MENU] key to switch to the selected zone. The corresponding regional alias will be displayed at the bottom of the screen.

Making a Call

Note: Press the [VFO/MR] key to switch the main channel to the other channel if there are 2 channels shown on the display. In standby mode, press and hold the [VFO/MR] key to switch between frequency (VFO) mode and channel (MR) mode.

  • Channel mode call: After selecting a channel, hold down the [PTT] key to initiate a call to the current channel. Speak into the microphone with a normal tone. When making a call, the red LED is on.
  • Frequency mode call: Press and hold the [VFO/MR] key to switch to frequency mode, input the working frequency within the allowable range, and press and hold the [PTT] key to transmit on the current frequency. Speak into the microphone with a normal tone. When making a call, the red LED is on.
  • Receive a call: When you release the [PTT] key, you can answer it without any action. When receiving a call, the green LED is on.

Note: To ensure the best reception volume, keep the distance between the microphone and your mouth at the time of transmission from 2.5 cm to 5 cm.

Emergency Alert

The Emergency Alert feature can be used to signal members in your group for help.

To activate the emergency alert function, press the pre-programmed [Emergency Alarm] key. Press it again to exit the emergency alert function.

WARNING:

The Emergency Alert feature should only be used in the event of an actual emergency.

FM Radio (FM)

Method 1: Press the [MENU] key, go to the main Menu -> Radio Settings -> Press/Longpress of "SK1/SK2" as [FM Radio], and turn on or off the radio by pressing the preset [FM Radio] key.

Method 2: Press the [MENU] key, go to the main Menu -> Radio Settings -> Radio On/Off, turn the radio on or off.

After turning on the radio function, the station search method is as follows:

  • Press the [#] key to enter radio search mode. The screen displays 'Seeking...', and the radio will automatically save the searched radio frequency as a radio channel (memory mode).
  • Press ▲ or ▼ to select the radio channel.
  • Directly input familiar radio frequency by numeric keys (frequency mode, e.g., 96.9MHz, input 969).
  • Short press the preset [FM Radio] key or [EXIT] key to exit the radio mode.

The frequency range to listen to the radio is 65-108MHz. When listening to broadcast FM, press the [MENU] key to switch between 65-75 MHz and 76-108 MHz band.

Radio Interrupt

  • On: When FM radio is used, you can still receive or transmit on the channel.
  • Off: When FM radio is used, the radio will not permit a transmission or reception.

Monitor

In standby, press the pre-programmed [Monitor] key to enter Monitor. This allows you to monitor weak signals even if the matched carrier has signaling. Press the [Monitor] key again to turn off the speaker and exit Monitor mode.

Keypad Lock

The radio features a keypad lock that locks out all keys except for the three side keys. To enable or disable the keypad lock, press and hold the [#] key for about two seconds. You can also enable automatic keypad lock after ten seconds from the menu.

Frequency Reversal

A short momentary press of the [EXIT] key enables the reverse function. If you want to listen to the repeater's input frequency, press the [EXIT] key momentarily to reverse your transmit and receive frequencies.

TX Repeaters Tone

Tone-bursts (1750Hz, 1000Hz, 1450Hz, 2100Hz) are mainly used for repeater activation, especially in Europe. Before using the Tone-burst function, the SK1/SK2 programmable key must be defined as the "1750Hz" function. Press the pre-programmed [1750Hz] key to send 1750Hz tone-bursts. This function is useful for communications through repeaters.

NOAA Weather/Weather Alert

Your radio has a NOAA Weather Radio function to receive weather reports from designated NOAA stations and a NOAA Weather Scan function to scan all 10 channels of the NOAA Weather Radio.

Press the [MENU] key >> NOAA weather >> Weather On/Off. Options:

  • Off: NOAA weather forecast function is not enabled.
  • WX1-WX10: Specific NOAA weather frequencies (e.g., WX1: 162.550 MHz, WX2: 162.400 MHz, etc.).

Press ▲ or ▼ to select a NOAA channel. Enable this channel and the NOAA icon will display on the first line. Note: Channels WX 1 through WX10 receive only NOAA and Canadian Weather Radio channels. You cannot transmit on these channels.

Weather Alert: Press the [MENU] key >> NOAA Weather >> Weather Alert. Options:

  • Off: Disables the Weather Alert function. The weather alert icon is not displayed.
  • On: Enables the weather alert function. The weather alert icon is displayed.

With the Weather Alert feature enabled, the radio returns to standby and can receive calls. It guards the radio channel and automatically cycles through the work channel and weather alert channel. Activating the Weather Alert feature and receiving a 1050 HZ alert signal will result in a loud beep, and the radio will automatically switch to weather broadcast mode.

Method 1: Press [MENU] key, go to the main Menu -> Radio Settings -> Press/Longpress of "SK1/SK2" as [OneTouch Search], and enter the frequency search mode by pressing the preset [OneTouch Search] key.

Method 2: Press the [OneTouch Search] key (green key) to enter the frequency search mode.

When using the OneTouch Search function, this unit will act as a receiver. Press the preset [OneTouch Search] key, the screen will display "Seeking" and the indicator light will be yellow. Successful seeking will display the search frequency and CTCSS/DCS, and turn on the speaker. You can press the [MENU] key to save the search frequency and CTCSS/DCS to the channel. Press and hold the [PTT] key to make a callback.

Advanced Features

Scanner

The radio features a built-in scanner for VHF and UHF bands. In Frequency (VFO) mode, it scans in steps according to your set frequency step. In Channel (MR) mode, it scans your channels. To enable the scanner, press and hold the [#] key for about two seconds. You can change the scanning direction with the ▲ or ▼ keys. Press and hold the [#] key to exit scanning mode.

Frequency Ranger: In frequency mode, the frequency sweep range can be precisely set by inputting the start and end values through the keyboard. (e.g., 144146 for 144.000-146.000MHZ).

Channel Scan Range: In channel mode, the scan range can be all channels in the current zone or channels added to the current zone.

Scan Modes: The scanner is configurable to one of three ways of operation: Time, Carrier, or Search.

  • Time Operation (TO): Scanner stops when it detects a signal, then resumes scanning after a factory preset timeout.
  • Carrier Operation (CO): Scanner stops when it detects a signal, then resumes scanning after a preset time with no signal.
  • Search Operation (SE): Scanner stops when it detects a signal. To resume scanning, press and hold the [#] key again.

Scan Sub-Code: To search for a CTCSS code:

  1. In VFO mode, enter a known frequency (e.g., 144.525).
  2. Press the [MENU] key to enter menu >> Scan >> Scan Sub-Code.
  3. Press ▲ or ▼ to select CTCSS.
  4. Press the [MENU] key to enter the CTCSS code, and scan in sequence. When a valid CTCSS code is scanned, it stays on the code, and the speaker is turned on.
  5. Press the [MENU] key to store the scanned CTCSS code and exit.

To search for a DCS code, follow similar steps, selecting DCS instead of CTCSS.

DTMF

DTMF (Dual-Tone Multi-Frequency) is an in-band signaling method using dual sinusoidal signals. It is commonly used in two-way radio systems for automation and remote control, such as activating amateur radio repeaters. The radio has full DTMF implementation, including A, B, C, and D codes. Numerical keys and the [*] and [#] keys correspond to DTMF codes. A, B, C, and D codes are located in the [A/B], [VFO/MR], and [EXIT] keys respectively. To send DTMF codes, press the corresponding key(s) while holding down the PTT key.

2Tone Enc / 5Tone Enc

Set a 2Tone or 5Tone ID as the default call ID for the current channel. Press the PTT key to transmit the selected 2Tone or 5Tone. Edit these in the PC programming software.

Dual Watch

The ability to monitor two channels at once can be achieved by having one receiver flip-flop between two frequencies (Dual Watch) or by having two receivers (Dual Receive or Dual VFO). This radio features Dual Watch functionality (single receiver) with the ability to lock the transmit frequency to one of the two channels it monitors.

Enabling/Disabling Dual Watch mode:

  1. Press the [MENU] key to enter the main menu.
  2. Enter 2 on the numeric keypad for Radio Settings.
  3. Press the [MENU] key to confirm, enter 18 on the numeric keypad for Dual Watch.
  4. Press the [MENU] key to select.
  • OFF: Disables dual-watch.
  • Double Wait: Enables dual-watch, displaying and monitoring both channels.
  • Signal Wait: Enables single-watch, displaying both channels but transmitting/receiving only on the main channel.

Press the [MENU] key to confirm, and the [EXIT] key to return to the previous menu. Press and hold [A/B] to switch Double Wait / Signal Wait / Off dual watch mode.

Manual Programming (Channels Memory)

The radio features 999 memory channels, each capable of storing receive/transmit frequencies, transmit power, group signaling information, bandwidth, ANI/PTT-ID settings, and a six-character alphanumeric identifier. In standby mode, press [VFO/MR] key to switch between Frequency (VFO) mode and Channel (MR) mode.

Repeaters Programming

These instructions assume you know your repeater's transmit and receive frequencies and are authorized to use it.

  1. Press [VFO/MR] key to set the transceiver to VFO mode.
  2. Use the numeric keypad to enter the repeater's output (your receive) frequency.
  3. Press [MENU] key, then [1][3] to get the offset frequency.
  4. Use the numeric keypad to enter the specified frequency offset.
  5. Press [MENU] key to confirm and save.
  6. Press [MENU] key, then [1][4] to get the offset direction.
  7. Use the ▲ or ▼ keys to select plus (positive) or minus (negative) offset.
  8. Press [MENU] key to confirm and save.
  9. (Optional) Save to memory (see "Manual programming") or set up CTCSS (see "CTCSS" section).
  10. Press [EXIT] to exit the menu.

If you experience problems connecting to the repeater, check your settings or repeat the procedure. Certain Amateur Radio repeaters (especially in Europe) use a 1750Hz tone burst to open up the repeater. If you are still unable to connect, contact the person in charge of the radio system or your local amateur radio club.

Amateur Radio Setup

For Amateur radio operators, the broadest possible settings are often needed for compatibility with various systems. This typically means turning off many features that might be needed for a commercial setup. Recommended settings for a typical Amateur radio setup:

  • Turn ANI, DTMFST, PTT-ID off and PTT-LT to 0ms (menu items 22-24).
  • Turn off Squelch Tail Elimination (Tail) features (menu items 26).
  • Turn roger beep (ROGER) off (menu item 10).

Program channel:

  • Set bandwidth to Wide (menu item 4).
  • Turn DCS and CTCSS off (menu items 5-8).
  • Turn Signaling code off and SPK-Mute (menu items 9 and 10).

Main Menu Functions

The menu function allows you to perform operations such as selecting zones, setting SCAN, Radio Settings, Program Channels, and viewing Radio Information.

Basic Use with Arrow Keys

  1. Press the [MENU] key to enter the main menu.
  2. Use the ▲ or ▼ keys to navigate between menu items.
  3. After finding the desired next menu item, press the [MENU] key again to select it.
  4. Use the ▲ or ▼ keys to navigate between the next menu items.
  5. After finding the desired next menu item, press the [MENU] key again to select it.
  6. Use the ▲ or ▼ keys to select the desired parameter.
  7. When you have selected the parameter, press [MENU] to confirm.
  8. To confirm your selection, press [MENU] and it will save your setting and bring you back to the main menu.
  9. To cancel your changes, press [EXIT] and it will reset that menu item and bring you out of the menu entirely.
  10. To exit out of the menu at any time, press the PTT key.

Using Shortcuts

Every menu item has a numerical value. These numbers can be used for direct access.

  1. Press the [MENU] key to enter the menu.
  2. Use the numerical keypad to enter the number of the menu item.
  3. To enter the menu item, press the [MENU] key.
  4. For entering the desired parameter, use arrow keys or the numerical keypad for the shortcut code.
  5. To confirm your selection, press [MENU] to save and return to the main menu. To cancel, press [EXIT].
  6. To exit the menu at any time, press the PTT key.

Quick Access Shortcuts:

  • [MENU] + 1: Quick access to Zones selection (up to 10 Zones, each storing 64 channels).
  • [MENU] + 2: Quickly enter Scan Settings (VFO frequency range, Scan mode, Scan Sub-Code, Scan Memory).
  • [MENU] + 3: Quickly enter Radio settings (general settings).
  • [MENU] + 4: Quick access to Program Channel (Alias, TX and RX Frequency, TX Power, Bandwidth, Display mode, Channel Memory and Channel delete).
  • [MENU] + 5: Quickly query radio information (ANI ID, Firmware version, Hardware version).
  • [MENU] + 6: Quickly enter GNSS position system settings (GNSS switch, time zone setting, position mode setting).

Radio General Settings

Add Zone: Press [VFO/MR] key to Channel Mode, then [MENU] key >> Zone >> Add Zone, name the newly added zone and save it. The new zone will be automatically configured with a channel, allowing parameters like Channel Name, Receive/Transmit Frequency, and CTCSS/DCS to be reset via the Channel Configuration menu.

Power On Display Setting:

  • Picture: The radio will display a preset picture (BMP format, 160x128 pixels) when powered on.
  • Message: Through CPS programming software (General Setup >> General Setup >> Power On Character) or self-station setup ([MENU] key >> Radio Setting >> Power On Message).
  • Voltage: The power voltage is momentarily displayed.

Display Reversal: For ease of use, the display interface can be oriented in STAN (normal) or FAIL (reversed) mode. Press [MENU] key >> Radio Settings >> DIR.

MDF-A/MDF-B Channel Mode A Display: [A][B] MR/Channel Mode Display Format. Freq: Displays programmed Frequency. Name: Displays the channel name. CH: Displays the channel number.

Alarm Model: Select the type of indication when an alarm is activated ([MENU] key >> Intercom Settings >> Alarm Type).

  • On Site: Alarm tone given locally; control center and group members do not receive the signal.
  • Code+Sound: Sends alarm code to control center/group members, then activates hot microphone and sends background tone. Receiver hears background sound.
  • Code+Sound(No): Sends alarm code to control center/group members; no local alarm tone, sound, or visual indication.
  • Code+Tone: Sends alarm code to control center/group members; local alarm tone emitted with audible and visual indications.

Auto Power Off: Allows setting automatic power off after 30, 60, 120, 240, or 480 minutes of inactivity. Off: Turns off the function.

Power-on Password: Sets a power-on password to protect device security. Press [MENU] key >> Radio Settings >> Password. Enter 1-8 digits (0-9), press [#] to display entry. Press [MENU] to save. To cancel, delete all digits and press [MENU]. When enabled, the radio prompts for password on power-on. The password can be read/modified by CPS software.

Channel Alias: Allows viewing or resetting the current channel alias. Press [MENU] + [4] for Program Channel, then [MENU] to select "CHL NAME". Press [MENU] to edit. Use [#] to switch input method, [1] for symbols, [2-9] for letters/numbers, [0] for space. Press [MENU] to save.

GPS Function

Optional features requiring hardware support. The position system is a typical DTMF calling application. Radios receiving/sending GPS location information must operate on the same frequency/channel and be set to the main frequency band. In GPS mode, you can only view location information and cannot make normal calls. Voice intercom requires exiting GPS mode. You can set system time, GPS on/off, time zone, and GPS mode via the position system menu. Press and hold [EXIT] key to view, share, and request location information.

GPS function displaying location on walkie talkie screen
The GPS function allows location sharing and acquisition (APRS function), compatible with YAESU (Transmit Only). Ensure radios operate on the same frequency/channel and are set to the main frequency band. In GPS mode, only location information is viewable; voice intercom requires exiting GPS mode.

Position On/Off: In standby, press [MENU] key >> GNSS >> GPS On/Off. Off: Disables. On: Activates, and the GPS icon displays.

My Position: In standby, press [MENU] key >> GNSS >> GPS Information. Enter "My Position" to display Longitude (E), Latitude (S), Speed, Altitude, number of Satellites, Date, and Time. "Position..." indicates blinking, "Position successful" indicates stable. Press [MENU] to confirm, and ▲ or ▼ to cycle through information. Press [EXIT] to return.

Share Position (Send position): In the member (local) display screen, press and hold the PTT key. The transmitter indicator briefly lights red to share local position information. The receiver displays the shared position and transmitter's member sequence.

Request a Position (Get a position): Press the [EXIT] key to return to the member list. Press ▲ or ▼ to select a member (not Host). Press and hold the PTT key; the transmit indicator briefly lights red, requesting position. The display updates upon successful acquisition. Press [MENU] to confirm, and ▲ or ▼ to cycle through information.

UTC Time Zone: In standby, press [MENU] key >> GNSS >> Time Zone >> Select plus or minus time.

Maintenance

Battery Maintenance Instructions

To help your battery work normally or prolong its life, observe the following:

  • Accumulated dust on the charging connector may affect normal charging. Use a clean and dry cloth to wipe it regularly.
  • It is recommended to charge the battery between 5°C~40°C. Violating this limit may reduce battery life or cause leakage.
  • To charge a battery attached to the product, turn it off to ensure a full charge.
  • Do not remove the battery or unplug the power cord during charging to ensure a smooth process.
  • Do not dispose of the battery in fire.
  • Do not expose the battery to direct sunlight for a long time or place it close to other heating sources.
  • Do not squeeze and penetrate the battery, nor remove its housing.

Troubleshooting Guide

Phenomena Analysis Solution
You cannot turn on the radio. The battery may be installed improperly.
The battery power may run out.
The battery may suffer from poor contact caused by dirty or damaged battery contacts.
Remove and reattach the battery.
Recharge or replace the battery.
Clean the battery contacts or replace the battery.
During receiving, the voice is weak or intermittent. The battery voltage may be low.
The volume level may be low.
The antenna may be loose or incorrectly installed.
Recharge or replace the battery.
Increase the volume.
Turn off the radio, and then remove and reattach the antenna.
The speaker may be blocked. Clean the surface of the speaker.
You cannot communicate with other group members. The frequency or signaling type may be inconsistent with that of other members. Verify that your TX/RX frequency and signaling type are correct.
You may be too far away from other members. Move towards other members.
You hear unknown voices or noise. You may be interrupted by radios using the same frequency.
The radio in analog mode may be set with no signaling.
Change the frequency, or adjust the squelch level.
Request your dealer to set signaling for the current channel to avoid interference.
You are unable to hear anyone because of too much noise and hiss. You may be too far away from other members.
You may be in an unfavorable position (e.g., blocked by high buildings or underground).
Move towards other members.
Move to an open and flat area, restart the radio, and try again.
It may be the result of external disturbance (e.g., electromagnetic interference). Stay away from equipment that may cause interference.
The radio keeps transmitting. VOX may be turned on or the headset is not installed in place. Turn off the VOX function. Check that the headphones are in place.

NOTE: If the above solutions cannot fix your problems, or you have other queries, please contact your dealer for more technical support.

Specifications

GENERAL
Channel Capacity640
Channel Spacing25.0 KHz/12.5 KHz
Input Voltage7.4 VDC
Battery Life: 5% TX, 5% RX, 90% StandbyLi-on: 15 hours @ 5 watts
Operating temperature-10°C to 60°C
Antenna Impedance50Ω
Radio Dimensions135mm x 63mm x 39mm (not including antenna)
Radio Weight290 g (with Li-ON battery)
TRANSMITTER
Frequency Range (TX)144 to 148 MHz, 420 to 450 MHz (America version)
144 to 148 MHz, 430 to 450 MHz (Canadian version)
*144 to 146 MHz, 430 to 440 MHz (EU CE version)
RF Output Power7 Watts Max
Modulation16K0F3E/11K0F3E
Spurious Emission-16 dBm<1GHz, -16 dBm>1GHz
Frequency Stability±2.5 ppm
Audio Distortion≤5%
FM Hum & Noise40 dB
RECEIVER
Frequency Range108-136, 136-174, 220-260, 350-390, 400 to 520 MHz (Scan Receiver)
*144 to 146 MHz, 430 to 440 MHz (EU CE version)
Sensitivity: 12 dB SINAD-120 dBm
Adjacent Channel Selectivity-60 dBm
Intermodulation and Rejection-70 dBm
Rated Audio Power Output0.75 Watts @ 16 Ω
Rated Audio Distortion≤5%

NOTE: All specifications may be modified without prior notice or liability.

User Tips

  • PC Programming: For advanced programming, use the official PC software. Always read the factory software data first, then save your custom settings to a new code plug to avoid errors. Ensure your programming complies with FCC (or EU) license certifications.
  • Legal Frequencies: Be aware that programming a channel does not automatically authorize its use. Transmitting on unauthorized frequencies is illegal and can lead to serious penalties. Listening is generally permitted, but always consult your local regulatory body for specific laws and regulations.
  • GPS Functionality: The radio includes a GPS function for location sharing and acquisition. Ensure all radios involved are on the same frequency/channel and main frequency band for this feature to work correctly. Remember that voice communication requires exiting GPS mode.

Frequently Asked Questions (FAQ)

Does this radio have GPS?
Yes, the Baofeng UV-5RH PRO features a GPS positioning function for location sharing and acquisition.
Can I program this radio using my PC?
Yes, the radio is PC programmable. You can use a programming cable and dedicated software to configure frequencies, bandwidth, and other settings. Refer to the 'PC Programming' tip in the User Tips section for important considerations.

Manufacturer Information

Disclaimer

The accuracy and completeness of the contents are sought in the process of compilation, but we do not bear any responsibility for possible errors or omissions. With the continuous development of technology, we reserve the right to change the design and specification of the product without notice. No copy, modification, translation, and dissemination of this handbook may be made in any form without the prior written authorization of our department.

Manufacturer

PO FUNG ELECTRONIC (HK) INTERNATIONAL GROUP COMPANY LIMITED
ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong
Website: www.baofengradio.com or www.pofungshop.com

Print version: 5RH PRO(501) V1.0


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.