METALFISH DH450

Contents

METALFISH DH450 Low Profile CPU Cooler

User Manual

1. Introduction

The METALFISH DH450 is a compact, low-profile CPU cooler designed for ITX systems and other space-constrained builds. Featuring 6 heatpipes and a 92mm PWM fan, it provides efficient cooling for CPUs with a TDP of up to 150W. This manual provides detailed instructions for installation, operation, maintenance, and troubleshooting.

METALFISH DH450 Low Profile CPU Cooler with RGB fan

Figure 1: METALFISH DH450 Low Profile CPU Cooler (Rainbow Fan Version)

2. Package Contents

Please check the package contents upon unboxing to ensure all components are present:

  • METALFISH DH450 CPU Cooler (Heatsink with pre-attached 92mm PWM Fan)
  • Intel Mounting Bracket Set
  • AMD Mounting Bracket Set
  • Fixed Nuts (4x)
  • Screws (4x)
  • Insulation Pads (4x)
  • Thermal Grease (1x syringe)
Diagram showing all components included with the METALFISH DH450 cooler

Figure 2: Included Cooler Parts and Accessories

3. Setup and Installation

Before installation, ensure your motherboard is compatible with the DH450 cooler. Refer to the specifications section for supported CPU sockets. Always power off your system and disconnect it from the power supply before handling internal components.

3.1. AMD Platform Installation

Follow these steps for installing the DH450 on an AMD motherboard:

  1. Step 1: Prepare Fixed Nuts
    Stick the black insulation pads onto the 4 fixed nuts.
  2. Step 2: Attach Bracket to Radiator
    Install the AMD socket mounting bracket onto the radiator.
  3. Step 3: Prepare Motherboard
    Remove the original AMD CPU cooler bracket from the motherboard. Keep the original backplate of the motherboard in place.
  4. Step 4: Apply Thermal Paste
    Clean any old thermal grease from the top of the CPU. Apply new thermal paste evenly onto the CPU IHS (Integrated Heat Spreader).
  5. Step 5: Adjust Screw Position
    Adjust the screw position on the cooler's mounting bracket according to your motherboard's installation holes.
  6. Step 6: Secure Cooler
    Place the cooler onto the CPU. From the back of the motherboard, tighten the four fixed nuts (with insulation pads) to secure the cooler.
  7. Step 7: Connect Fan Cables
    Connect the 4-pin fan cable to the CPU_FAN header on your motherboard. If your cooler has an ARGB fan, connect the ARGB cable to a 5V 3-pin ARGB header on your motherboard (only applicable to ARGB versions).
Detailed 7-step installation guide for AMD platforms

Figure 3: AMD Platform Installation Instructions

3.2. Intel Platform Installation

Follow these steps for installing the DH450 on an Intel motherboard:

  1. Step 1: Prepare Fixed Nuts
    Stick the black insulation pads onto the 4 fixed nuts.
  2. Step 2: Attach Bracket to Radiator
    Install the Intel socket mounting bracket onto the radiator.
  3. Step 3: Apply Thermal Paste
    Clean any old thermal grease from the top of the CPU. Apply new thermal paste evenly onto the CPU IHS (Integrated Heat Spreader).
  4. Step 4: Adjust Screw Position
    Adjust the screw position on the cooler's mounting bracket according to your motherboard's installation holes.
  5. Step 5: Secure Cooler
    Place the cooler onto the CPU. From the back of the motherboard, tighten the four fixed nuts (with insulation pads) to secure the cooler.
  6. Step 6: Connect Fan Cables
    Connect the 4-pin fan cable to the CPU_FAN header on your motherboard. If your cooler has an ARGB fan, connect the ARGB cable to a 5V 3-pin ARGB header on your motherboard (only applicable to ARGB versions).
Detailed 6-step installation guide for Intel platforms

Figure 4: Intel Platform Installation Instructions

4. Operating Instructions

The METALFISH DH450 features a PWM (Pulse Width Modulation) fan. This allows your motherboard to dynamically control the fan speed based on CPU temperature, providing an optimal balance between cooling performance and noise levels. Ensure the fan is connected to a 4-pin CPU_FAN header on your motherboard for PWM functionality.

  • Fan Speed: The fan operates within a range of 900 to 2800 RPM (±10%).
  • Noise Level: The noise output ranges from 18 to 28 dBA, depending on the fan speed.
  • RGB Lighting (if applicable): If you have the ARGB version, the lighting can be controlled via your motherboard's RGB software, provided it's connected to a compatible 5V 3-pin ARGB header.

5. Maintenance

Regular maintenance helps ensure optimal performance and longevity of your CPU cooler.

  • Dust Cleaning: Periodically inspect the heatsink fins and fan blades for dust accumulation. Use compressed air or a soft brush to gently remove dust. Ensure the fan is held in place while cleaning with compressed air to prevent over-spinning and potential damage.
  • Thermal Paste: The thermal paste applied during installation typically lasts for several years. If you notice a significant increase in CPU temperatures over time, consider reapplying fresh thermal paste. This involves carefully removing the cooler, cleaning off old thermal paste from both the CPU and cooler base, and applying new thermal paste before reinstallation.

6. Troubleshooting

If you encounter issues with your METALFISH DH450 cooler, refer to the following common problems and solutions:

  • Fan Not Spinning:
    • Check if the 4-pin fan cable is securely connected to the CPU_FAN header on the motherboard.
    • Ensure the system is powered on and the CPU is generating heat (the fan may not spin at very low temperatures if configured by the motherboard BIOS).
    • Check motherboard BIOS settings for fan control.
  • High CPU Temperatures:
    • Verify that the cooler is securely mounted to the CPU and there is no wobble.
    • Ensure sufficient thermal paste was applied evenly and correctly.
    • Check for proper airflow within your PC case. Ensure case fans are correctly oriented to bring in cool air and exhaust hot air.
    • Dust accumulation on the heatsink fins can impede heat dissipation. Clean the cooler as described in the Maintenance section.
    • Confirm your CPU's TDP does not exceed the cooler's rated 150W capacity, especially under heavy load or overclocking.
  • RGB Lighting Not Working (ARGB version):
    • Ensure the 5V 3-pin ARGB cable is correctly connected to a compatible ARGB header on your motherboard.
    • Check your motherboard's RGB software for lighting control settings.
    • Verify that the ARGB header is enabled in your motherboard's BIOS, if applicable.

7. Specifications

FeatureSpecification
Model NumberDH450
Cooler TypeLow Profile
Cooler Dimensions (L x W x H)110 x 92 x 45 mm
Heatpipes6 x Φ6mm
TDP (Thermal Design Power)150W
Fan Size (L x W x H)92 x 92 x 15 mm
Fan Speed900 - 2800 RPM ±10%
Airflow (Air Volume)12.59 - 38.9 CFM ±10%
Air Pressure2.19 mmH2O
Noise Level18 - 28 dBA ±10%
Bearing TypeHydraulic Bearing
Fan Life50,000 hours
Power Interface4-Pin PWM
Blade Quantity9
Supported CPU SocketsIntel: LGA 1150, 1151, 1155, 1156, 1170, 1200, 1366, 1700, 1851, 2011, 2066
AMD: Socket AM2, AM3, AM4, AM5, FM1, FM2
CertificationsCE, FCC, RoHS

8. User Tips

Based on user experiences, consider the following tips for optimal performance:

  • Case Airflow: For best cooling results, especially in small form factor (ITX) cases, ensure your PC case has adequate airflow. Proper intake and exhaust fan configurations can significantly impact CPU temperatures.
  • Temperature Monitoring: Regularly monitor your CPU temperatures using system monitoring software to ensure it stays within safe operating limits, particularly during demanding tasks.

9. Warranty and Support

For warranty claims or technical support, please contact the seller or retailer from whom you purchased the METALFISH DH450 CPU Cooler. Keep your proof of purchase for warranty validation.

Additional information may be available in the official PDF user manual: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.