UKGF K-P10APR

Contents

UKGF K-P10APR 10-Inch Car Subwoofer Instruction Manual

Model: K-P10APR

Brand: UKGF

1. Introduction

This manual provides essential information for the safe and efficient installation, operation, and maintenance of your UKGF K-P10APR 10-inch car subwoofer. Please read it thoroughly before use to ensure proper functionality and to prevent damage to the product or personal injury.

2. Safety & Warnings

  • Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.
  • Professional installation is required. Securely fasten the speakers to designated vehicle mounting points (such as door panels or trunks) to prevent slipping, loosening, or damage from bumps and sudden braking, avoiding noise generation.
  • During installation, avoid key components such as vehicle airbags, steering systems, and fuel lines to avoid obstructing the path of airbag deployment and affecting vehicle safety performance.
  • The speaker wiring should be matched with the power of the car amplifier and the host to avoid burning the speaker due to high power, or affecting the sound effect due to low power, and causing component overheating.
  • Connect the wires strictly according to the markings (positive "+", negative "-"). Reversing the positive and negative poles can cause distortion of sound effects, abnormal diaphragm vibration, and long-term use may damage the speaker.
  • Ensure that the terminals are firmly connected during wiring, wrap the interface with insulating tape to avoid virtual connections and short circuits. The wiring harness should be organized in a standardized manner and kept away from high-temperature components of the vehicle (such as exhaust pipes) to prevent aging and damage to the wiring harness.
  • When the vehicle is parked for a long time, turn off the power of the car audio system to avoid the speaker being in standby mode for a long time. At the same time, take protective measures to prevent dust and debris from entering.

3. Specifications

Feature Specification
Product Name10 Inch Ultra-Thin Active Subwoofer
ModelK-P10APR
Rated Power200W
Peak Power800W
Impedance2.5 Ohms
Frequency Response20Hz~15kHz
Audio SensitivityMore than 90dB
Bass Improvement0 to +12dB
Total Harmonic Distortion<0.4%
Rated Value Of Fuse15A
Size (L x W x H)345mm x 260mm x 68mm
Item Weight5.4kg
Voltage12 V
Speakers TypesBass Speakers
MaterialAluminum Alloy
CertificationCE
Dimensions of the subwoofer: 345mm length, 260mm width, 68mm height.
Figure 1: Subwoofer dimensions (345mm x 260mm x 68mm).

4. Package Contents

The package includes:

  • 1 x UKGF K-P10APR Car Subwoofer
UKGF K-P10APR 10-inch car subwoofer and its retail packaging.
Figure 2: Subwoofer and packaging.

5. Setup & Installation

5.1. Before First Use

  • Accessory Inspection: Confirm that the speaker host, installation screws, wiring terminals, waterproof rings (if necessary) and other accessories are complete and undamaged.
  • Installation Position: Select dedicated installation positions such as vehicle door panels and trunk to ensure space adaptation, ventilation and dryness, and avoid key components such as airbags and fuel lines.
  • Tool Preparation: Gather screwdrivers, wire strippers, cable ties, electrical tape, and other necessary tools.

5.2. Wiring Diagram

Wiring diagram for the car subwoofer showing connections for power, ground, remote, RCA inputs, and controls.
Figure 3: Subwoofer control panel and wiring connections. Labels include: Low frequency regulation, Low level RCA input, Grounding wire, Power amplifier control line, +12V positive pole, On/Off switch, Volume adjustment, Left channel input, Right channel input, and Fuse.

5.3. Installation Steps

  1. Disconnect Power Supply: Turn off the power supply of the onboard host and amplifier. Disconnect the negative terminal of the vehicle battery to avoid short circuits caused by live wiring.
  2. Fixed Speaker: Place the speaker smoothly into the chosen installation position. Firmly fix it with matching screws and install a waterproof ring (if necessary) to ensure it does not loosen or shake when the vehicle is bumpy.
  3. Wiring Operation: Connect the speaker to the host/amplifier according to the positive "+" and negative "-" markings. Ensure the positive and negative poles are consistent and the terminals are firm. Wrap the interface with insulating tape, organize the wiring harness in a standardized manner, and keep it away from high-temperature components.
  4. Recovery and Debugging: After checking all wiring is correct, reconnect the negative terminal of the battery. Turn on the host and amplifier, adjust the volume and sound effects, and confirm that the speaker is working properly and without noise.

6. Operation

  • Power On and Off: The subwoofer is designed to synchronize power on and off with the onboard host and amplifier, eliminating the need for separate operation. It is recommended to turn off the host before turning off the engine to avoid battery depletion.
  • Sound Effect Adjustment: Adjust the volume, high, and low frequencies through the car host or amplifier. Avoid prolonged high volume and high power output to prevent speaker overload damage and ensure driving safety.
Video 1: Demonstration of the subwoofer's bass output and operation.

7. Maintenance

  • Daily Use: Avoid touching the speaker diaphragm with sharp objects. Prohibit foreign objects from entering the cavity to prevent sound quality distortion or component damage.
  • After Use: Turn off the device and store it in a dry place. Keep away from children.
  • Regular Checks: Regularly check whether the wiring terminals are secure, whether the wiring harness is damaged, whether there is no abnormal noise from the speaker, and whether the diaphragm is damaged. Any abnormalities should be dealt with in a timely manner.

8. Troubleshooting

If you experience issues such as no sound, distorted audio, or unexpected behavior, first re-check all wiring connections for security and correct polarity. Ensure the power supply is stable and the amplifier settings are appropriate for the subwoofer. If problems persist, consult a professional car audio technician.

9. User Tips

  • For optimal bass performance, consider the placement of the subwoofer. Under-seat installation often provides a balanced sound, while trunk placement might require more tuning to integrate with front speakers.
  • Start with lower volume and gain settings and gradually increase them to find the sweet spot without distortion or overloading the speaker.

10. Warranty & Support

Manufacturer Information

Company Name: Guangzhou Kuer Automotive Supplies Co., Ltd.

Address: Yiyou (International) Auto Parts Commodities Trading Center, No.155 HengFu Road

Email: 1033789983@qq.com

EU Authorized Representative

Company Name: E-CrossStu GmbH

Address: Felix-Dahn-Str 4

Email: E-CrossStu@web.de

Importer Information

Importer Name: Guangzhou Kuer Automotive Supplies Co., Ltd.

Address: Yiyou (International) Auto Parts Commodities Trading Center, No. 155 HengFu Road

A detailed user manual in PDF format is available for download. Please refer to the seller's product page or contact customer support for the link: User Manual (PDF)

11. Compliance & Certification

This product is CE certified, indicating compliance with relevant EU health, safety, and environmental protection legislation.

  • Certificate Number: KOT-2021063828C
  • Test Standards:
    • EN 55032:2015+A11:2020
    • EN 55035:2017+A11:2020
    • EN 61000-3-2:2019
    • EN 61000-3-3:2013+A1:2019
    • EN 61000-4-2:2009
    • EN 61000-4-3:2020
    • EN 61000-4-4:2012
    • EN 61000-4-5:2014+A1:2017
    • EN 61000-4-6:2014
    • EN 61000-4-8:2010
    • EN 61000-4-11:2020
CE certification document for the UKGF K-P10APR car subwoofer.
Figure 4: CE Certificate of Compliance.

© 2024 UKGF. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.