1. Introduction
This manual provides essential instructions for the safe and efficient operation of your ZJIVNV ZX-2000W Switching Power Supply. This device is a high-power, adjustable DC power supply designed for various electronic equipment, offering constant voltage (CV) and constant current (CC) modes, along with external control capabilities. Please read this manual thoroughly before installation and use.
Figure 1: ZJIVNV 2000W Switching Power Supply, highlighting adjustable voltage, protection, constant current/voltage (CC CV) features, and outside sign control.
2. Safety Information
Observe the following safety precautions to prevent injury and damage to the power supply:
- **Environmental Conditions:** Operating the power supply in abnormal environments (e.g., high humidity, excessive dust, acid-base pollution) will significantly reduce its service life. Ensure the operating environment is clean and dry.
- **Installation:** Remove all outside plastic packing materials before installation to ensure proper ventilation.
- **Fasteners:** Do not use screws that are excessively long, as they may come into contact with the internal circuit board or components, leading to damage or dangerous conditions.
- **AC Input Voltage:** Always verify and set the AC input voltage switch (115V or 230V) correctly according to your local power supply before powering on the unit. Incorrect voltage selection can severely damage the switching power supply.
- **Voltage Fluctuations:** If your supply voltage fluctuates dramatically (over-voltage/low-voltage), consider installing a power stabilizer or an over/under voltage protector to safeguard the equipment.
- **Electrical Equipment:** When supplying power to large electrical equipment, consider installing an AC filter before connecting to the power supply.
- **Cooling:** Ensure the power supply operates in an environment with unblocked airflow to prevent overheating and extend its lifespan.
Figure 2: The power supply includes short circuit, overload, and over-temperature protection for safe and secure use.
3. Product Overview
The ZJIVNV ZX-2000W is a robust switching power supply featuring:
- **Adjustable Output:** Provides adjustable DC voltage and current.
- **Protection Features:** Built-in short circuit, overload, and over-temperature protection.
- **Constant Voltage (CV) & Constant Current (CC):** Operates in both CV and CC modes.
- **Outside Sign Control:** Allows for external control of the power supply.
- **High Current Terminals:** Equipped with high current wiring terminals capable of carrying larger currents, reducing heating and ensuring sensitive contact.
- **Efficient Cooling:** Features three high-performance cooling fans for low noise operation and internal over-temperature protection.
Figure 3: The power supply is equipped with three high-performance cooling fans for effective heat dissipation and low noise operation.
4. Setup and Installation
4.1. Terminal Identification
The power supply features clearly marked terminals for input, output, and control:
- **AC Input:**
- **L:** Live wire
- **N:** Neutral wire
- **# (Earth):** Earth wire
- **DC Output:**
- **+V:** Positive pole
- **-V:** Negative pole
- **Multi DC Output (if applicable):** +V1, +V2, +V3, +V4, -V1, -V2, -V3, -V4, or direct voltage value markings. Common interface is "COM".
- **Outside Sign Control:** Terminals for external control signals (e.g., +5V, GND, +12V, OFF, +).
4.2. Pre-Power On Checks
- **Wiring Verification:** Ensure all input and output lines are correctly connected. For AC input, connect live, neutral, and earth wires. For DC output, connect positive and negative poles.
- **Input Wire Cross-Section:** Verify that the cross-section of the input electric wire is sufficient to prevent excessive voltage drop (AC voltage drop should not exceed 5%, DC voltage drop not exceed 0.5%).
- **Connections:** Check that all screw connections and switching device (board) contacts are secure and have good contact.
- **Insulation & Withstand Voltage:** Confirm that the shell, input, and output insulation resistance and withstand voltage meet the required specifications.
- **Grounding:** The earth wire must be firmly grounded to ensure safety and reduce interference. The cross-sectional surface of the grounded copper wire should exceed 0.75mm².
4.3. AC Input Voltage Selection
Locate the AC input voltage switch on the unit. Set it to either 115V or 230V, corresponding to your local mains voltage. Failure to select the correct voltage can cause irreversible damage to the power supply.
Figure 4: High current wiring terminals for input (Ground, Input L, Input N), output (Output Negative, Output Positive), and outside sign control (+5V, GND, +12V, OFF, +).
5. Operating Instructions
5.1. Output Characteristics
This switching power supply may feature main and secondary outputs. The main output generally offers superior characteristics. Typically, the main output is the one with a higher rated output current or is intended for stable load power where the electricity output current is not too small.
If you are using only the secondary output, a dummy load equivalent to 30% of the rated power output must be added to the main road. This requirement may not apply to custom-made power supplies or dedicated power supplies, but users must specify this requirement before ordering.
5.2. Adjustable Voltage and Current
The power supply allows for adjustment of both output voltage and current. Use the designated potentiometers or external control signals (via the outside sign control terminals) to set the desired output parameters. The unit will operate in either Constant Voltage (CV) or Constant Current (CC) mode depending on the load and set limits.
5.3. Outside Sign Control
The outside sign control terminals enable external devices or systems to control the power supply's operation. Refer to the specific pinout on the wiring diagram (Figure 4) for connections such as +5V, GND, +12V, OFF, and + for various control functions.
6. Maintenance
- **Environmental Control:** Maintain a clean, dry, and well-ventilated operating environment. Avoid exposure to excessive dust, high humidity, and corrosive substances (acid-base pollution) to maximize the lifespan of the SMPS.
- **Cooling System:** Ensure the cooling fans are free from obstructions and dust buildup. Regular cleaning of the fan grilles can help maintain optimal cooling performance.
- **Connections:** Periodically inspect all wiring connections for tightness and signs of wear or corrosion.
7. Troubleshooting
- **Reduced Lifespan:** Frequent on/off cycling of the input voltage or operating in abnormal environmental conditions can negatively impact the power supply's lifespan.
- **Voltage Fluctuations:** If the input voltage fluctuates significantly (over-voltage or low-voltage), the power supply's performance may be affected. Consider using a power stabilizer or over/under voltage protector.
- **Temperature Issues:**
- If the environment temperature exceeds 40°C (e.g., 70°C), the output power should be reduced (e.g., to 50% of the rated output at 70°C).
- The switching power supply may not start or output normally if the environment temperature is below -10°C.
- **No Output/Failure to Start:** Ensure proper ventilation and unblocked airflow around the unit. Blocked airflow can lead to over-temperature protection activation or reduced lifespan.
8. Specifications
| Attribute | Value |
|---|---|
| Type | Power Supply |
| Model Number | ZX-2000W |
| Brand Name | ZJIVNV |
| Output Power | 2000W |
| Rated Capacity | 40-1000VA |
| Input Voltage | 180-264VAC |
| Output Current | 0-100A |
| Output Frequency | 45-65HZ |
| Output Type | SINGLE |
| Product Size (L*W*H) | 275*155*70mm |
| Certification | CE, FCC, RoHS, KC |
| Origin | Mainland China |
| Warranty | 1 year |
8.1. Output Voltage and Current Combinations
Figure 5: Dimensions and detailed output specifications for the 2000W power supply.
| Output Voltage | Output Current Range |
|---|---|
| 12V | 0-166.6A |
| 24V | 0-83.3A |
| 36V | 0-55.5A |
| 48V | 0-41.6A |
| 60V | 0-27.7A |
| 72V | 0-27.7A |
| 96V | 0-20.8A |
| 110V | 0-18.1A |
| 150V | 0-13.3A |
| 220V | 0-9A |
9. User Tips
- Always double-check your wiring before applying power to avoid damage to the unit or connected devices.
- For applications requiring precise voltage or current, use external meters to verify the output settings.
- Ensure adequate ventilation, especially when operating at high power outputs, to prevent the unit from overheating.
10. Warranty and Support
This ZJIVNV Switching Power Supply comes with a 1-year warranty from the date of purchase, covering manufacturing defects. For technical support or warranty claims, please contact your retailer or the manufacturer directly. Please have your model number (ZX-2000W) and purchase information ready.
A PDF version of this user manual is available for download. For detailed documentation, please refer to the official user manual PDF.