ToolkitRC M8D

Contents

ToolkitRC M8D Intelligent Charger User Manual

Model: M8D

Manual Version: V1.0 (2024.05)

1. Introduction

Thank you for purchasing the M8D balance charger. Please read this manual carefully before use to ensure proper operation and safety.

Key Points

  • 💡 Tips: Helpful advice for optimal use.
  • ⚠️ Important: Critical information to prevent damage or injury.
  • 📄 Information: General details and explanations.

Further Information

To ensure you have the best experience with this product, visit the official ToolkitRC website at www.toolkitrc.com for news, information, and firmware updates.

An official user manual in PDF format is available for download. For detailed instructions and diagrams, please refer to the PDF manual provided by the manufacturer.

2. Safety Information

⚠️ WARNING: Failure to follow these safety instructions may result in fire, property damage, or personal injury.

  1. The M8D allows an input voltage of DC 10.0V-49.0V. To ensure that the power supply voltage is consistent, pay attention to the positive and negative polarity of the power supply before use.
  2. Do not use this product in hot or humid environments. Keep away from flammable liquids and gases.
  3. Never leave charging batteries unattended. Always supervise the charging process to deal with abnormalities safely.
  4. When not in use, please turn off/unplug the device.
  5. When using the charging function, please set a current that matches the battery performance envelope. Do not set an excessive current for charging to avoid damage to the battery. Check the guidelines of your battery's manufacturer for correct charging instructions.
  6. Choosing the wrong battery type for charging may damage the battery, charger, burn, and other dangers. Please be sure to choose carefully.
  7. Do not charge batteries that are not labeled with a battery type.
  8. When charging a lithium battery, only connecting to the main port will not perform balance management. Please pay attention to the balance of the battery. After connecting to the balance port, it will automatically begin balance management.
  9. The battery destruction function should only be used for safe disposal of batteries. Using it on batteries in normal use can cause irreversible damage.

⚠ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

3. Product Overview

Product Description

The M8D is a touch screen balanced charger product with a total charging power of up to 1600W. It features an IPS bright display and a capacitive touch screen combined with a roller encoder for convenient operation.

Key Features

  • Charge, discharge, and balance management for LiPo, LiHV, LiFe, Lion LTO 1-8S, NiMh 1-20S, PB 1-15S batteries.
  • DC power supply: 10.0-49.0V MAX 1600W.
  • Charging power: MAX 30.0A @MAX800W*2 ASYN, MAX 50.0A @MAX1600W SYNC.
  • Discharging power: MAX 10A@40W*2 normal, MAX 30A@800W*2 recycle.
  • Charging accuracy: <0.005V.
  • Balancing current: 2000mA.
  • Built-in 65W USB-C fast charger.
  • Lithium battery cut-off voltage can be set (TVC).
  • Automatically allocates input power.
  • Multi-language system (supports 11 languages).
  • Can record 10 commonly used battery profiles.
  • Can record 3 groups of commonly used power sources.

M8D Layout

Front view of ToolkitRC M8D charger with labeled components
Figure 3.1: Front View of M8D Charger. Key components include the Display/Touch panel, CH/Exit button, two Main ports, two Balance ports, and a Scroll wheel.
Back view of ToolkitRC M8D charger with labeled components
Figure 3.2: Back View of M8D Charger. Features include the DC input XT90 port, USB A/C output, and Cooling fans.

The M8D features an extra-large flip screen design, allowing the IPS 3.5" display to flip from 32° to 80° for a comfortable viewing angle.

Video 3.1: ToolkitRC M8D Product Overview. This video demonstrates the charger's touchscreen interface, dual-channel output, adjustable screen, 65W fast charging, battery destruction function, dual fans, and TF card logging capabilities.

4. Setup

4.1 Connecting Power

  1. Connect the M8D device to a DC 10-49V power source using the XT90 input port.
  2. Ensure correct positive and negative polarity of the power supply.

4.2 Initial Boot-up

  1. The screen will display the boot logo for approximately 2 seconds.
  2. An audible tone will accompany the boot sequence.
  3. After booting, the screen will enter the main interface.

4.3 System Settings

To enter system settings, select the Settings icon (Settings icon) on the main interface, or press and hold the scroll wheel for 2 seconds when both channels are idle.

Screenshot of Input Settings menu on M8D charger
Figure 4.1: Input Settings Interface.
  • Input Power: Save and select from P1, P2, P3 profiles. Set power, current, and voltage for the input power supply.
  • Power Type: Defines the input power supply type. Discharge function can be set to recycling only when input is set to battery.
  • Power Selection: If enabled, the charger will prompt you to select a power number each time it powers on.
  • Max Power: The maximum power absorbed from the input port during charging.
  • Max Current: The maximum current drawn from the input port during charging.
  • Min Voltage: The lowest allowable input voltage.

Charging Safety Settings

Screenshot of Charging Safety Settings menu on M8D charger
Figure 4.2: Charging Safety Settings Interface.
  • Safe Inter Temp: If the internal temperature exceeds this value, the device will stop the main port output.
  • Safe Exter Temp: External temperature limit.
  • Safe Time: The maximum time of continuous charging. Charging will stop if this time is exceeded.
  • Safe Capacity: The maximum capacity for continuous charging. Charging will stop if this capacity is exceeded.
  • Synchronous Mode: When enabled, both channels can be combined to charge the same battery, with a maximum current of 50A.
  • Continuous Operation: If enabled, after a battery is fully charged and removed, connecting the next battery will automatically continue charging with the previous settings.
  • Work Complete: Determines whether to stop or trickle charge when charging is complete.
  • Balancing Start Voltage: Sets the voltage at which the battery begins balancing relative to its full voltage.

General System Settings

Screenshot of General System Settings menu on M8D charger
Figure 4.3: General System Settings Interface.
  • Backlight: Adjust the backlight brightness level from 1 to 10.
  • Sound Volume: Set the speaker volume to high, medium, low, or off.
  • Language: Change the system display language (supports 11 languages).
  • Theme Style: Select between Light and Dark themes.
  • SD-log: Configure logging interval settings for the TF card.
  • Manual Calibration: Calibrate voltage values if the display deviates from the actual battery voltage.
  • Default: Restore all settings to factory values.
  • ID: Displays the unique ID of the device.

5. Operation

5.1 Quick Start

Screenshot of the main interface of the M8D charger
Figure 5.1: Main Interface after Boot-up.
  1. Touch the main interface or scroll the [Scroll Wheel] to select a desired function. Press the [Scroll Wheel] to confirm.
  2. Touch the [Settings icon] or press and hold [Scroll Wheel] to enter system settings.
  3. Touch the [Info] button or scroll the [Scroll Wheel] to select [Info] to display voltage and internal resistance for the corresponding channel.
  4. Touch [Status] or short press [Scroll Wheel] to select [Status] to choose a charging task when the channel is idle.
  5. You can adjust and end work while a channel is active.
  6. Press the [Exit Button] to end modification or return to the previous interface.

💡 Tips:

  • Short press [Scroll Wheel] once to confirm a function.
  • Long press [Scroll Wheel] for 2 seconds for the delete key function.
  • A 'didi' sound confirms successful key operation.

5.2 Charging Settings

From the main interface, select and short press [Scroll Wheel] to enter the charging function. If "Battery selection" is enabled in system settings, you can save up to 10 battery records.

Screenshot of Battery Selection menu on M8D charger
Figure 5.2: Battery Selection Interface.

Battery Type

Select an existing battery profile or press [New Battery] to create a new one. You can modify the battery type as shown below:

Screenshot of Battery Type selection menu on M8D charger
Figure 5.3: Battery Type Modification Interface.

The charger supports 7 types of batteries: LiPo, LiHV, LiFe, Lion, LTO, NiMH, and PB. Select the type that matches your battery and press [Confirm].

Battery Type Nomenclature:
  • LiPo: Lithium polymer battery, nominal voltage 3.70V, 4.20V when fully charged.
  • LiHV: High-voltage lithium battery, nominal voltage 3.85V, 4.35V when fully charged.
  • LiFe: Lithium iron battery, nominal voltage 3.30V, 3.60V when fully charged.
  • Lion: Lithium-ion battery, nominal voltage 3.60V, 4.10V when fully charged.
  • LTO: Lithium-ion battery, nominal voltage 2.40V, 2.70V when fully charged.
  • NiMh: Nickel-hydrogen battery, nominal voltage 1.20V.
  • PB: Lead-acid battery, nominal voltage 2.00V.

Number of Cells

Move the cursor to "Battery Cells" and short press [Scroll Wheel] to modify the number of cells.

Screenshot of Number of Cells selection menu on M8D charger
Figure 5.4: Number of Cells Setting Interface.

Scroll the [Scroll Wheel] to adjust the value. When set to [Auto], the charger automatically identifies the number of cells based on the voltage of the connected battery. Press [Confirm] to apply.

⚠️ Important:

  • Over-discharged or overcharged batteries may cause incorrect cell count identification. Manual adjustment may be necessary.
  • Incorrectly setting the number of cells can prevent charging or cause overcharging damage.
  • Lixx batteries are identified more accurately when connected to the balance port.

Mode

Modify the work mode as shown below:

Screenshot of Mode selection menu on M8D charger
Figure 5.5: Mode Selection Interface.

Available modes include Charge, Discharge, Cycle, and Destroy. LiPo, LiHV, LiFe, and Lion batteries support Charge and Storage modes. NiMh and PB batteries support Charge mode only. Press [Confirm] to apply.

End Voltage Setting (TVC)

Move the cursor to [End Voltage] to modify the cut-off voltage for monolithic batteries.

Screenshot of End Voltage Setting menu on M8D charger
Figure 5.6: End Voltage Setting Interface.
  • When charging, this is the charging cut-off voltage (range: ±50mV of full voltage).
  • When discharging, this is the discharging cut-off voltage.
  • Adjust in 0.01V increments.

⚠️ Important:

  • Only LiPo, LiHV, LiFe batteries allow cut-off voltage adjustment.
  • Do not modify the cut-off voltage if you are unfamiliar with battery characteristics.
  • TVC stands for Terminal Voltage Control.

Charging Current

Move the cursor to [Charging Current] and slide the [Slider] or scroll the [Scroll Wheel] to adjust the current. The charger supports up to 30A.

Screenshot of Charging Current adjustment menu on M8D charger
Figure 5.7: Charging Current Adjustment Interface.

💡 Tips:

  • Set the charging rate to 1-2C according to battery capacity. For example, a 2000mAh battery should be charged at 2.0-4.0A.
  • Always refer to your battery manufacturer's guidelines for correct charging instructions.

NiMh Setting (PeakV)

When the battery type is NiMh, the PeakV value can be set within a range of 3mV-15mV.

Screenshot of NiMh PeakV setting menu on M8D charger
Figure 5.8: NiMh PeakV Setting Interface.

💡 Tips:

  • Only NiMh batteries allow setting the battery negative pressure value.
  • PeakV: The voltage drop peak value of each cell when the NiMH battery is fully charged.

5.3 Charging/Discharging Process

When charging starts, the charger enters the working interface:

Screenshot of the M8D charger's charging in progress screen
Figure 5.9: Charging in Progress Interface.
  • Select the [Info] button to view the voltage value of the corresponding channel. Slide the voltage information to the left to switch to the internal resistance display.
  • Select [Status Bar] to dynamically set the working current or stop working.
Screenshot of the M8D charger's internal resistance display
Figure 5.10: Internal Resistance Display. Shows internal resistance for each cell (e.g., 5.2mΩ for the first cell battery).

Ending Operations

To end charging or discharging, select [Channel 1 - Stop] (or the relevant channel) to stop the work and return to the main interface.

Display Content Description (Example Values):

  • 24.0V: Input supply voltage.
  • 14.8A: Input supply current.
  • 20Wh: Cumulative power consumption of the input power supply.
  • 45°C: Internal temperature of the charger.
  • 32.23V: Voltage of the main port of the first channel.
  • 5.00A: Current of the main port of the first channel.
  • 10:59: First channel working hours.
  • 2000mAh: Cumulative capacity of the first channel.
  • 4.200V: Voltage of the first battery cell.
  • 4.200V (Red mark): Indicates the fourth battery cell is under balance management.
  • -.--V: No battery connected.

5.4 Other Functions

Firmware Upgrade

Connect the M8D to a computer using the provided USB data cable. The computer will recognize a USB drive named "Toolkit". Download the upgrade file (app.upga) from the official website. Copy and paste the new file, overwriting the existing files in the USB drive to upgrade the firmware.

Automatic Continuous Charging

When a battery is fully charged, after unplugging it and connecting the next battery, the device will automatically continue to charge. This function can be enabled or disabled in the settings menu.

Fan Stepless Speed Regulation

When the internal temperature exceeds 43°C, the fan speed will increase linearly with temperature or power increase. This design aims to reduce noise during low-temperature or low-power operation.

USB Fast Charging

The M8D has a built-in USB fast charging protocol, supporting up to 65W charging power via the Type-C port. Supported protocols include PD, QC, AFC, FCP, SCP, PE, SFCP, and VOC.

Manual Voltage Calibration

In the system settings, access the manual voltage calibration function. Use a voltmeter to measure the actual voltage of each battery. Move the cursor to the corresponding voltage value and modify it to match the voltmeter reading for calibration. Save the settings after calibration.

Fully Charged Replenishment

When a lithium battery is charged, it will prompt "Fast charging has ended". If the battery is not removed, it will automatically be charged at a constant voltage trickle to bring the battery to a fuller state.

Battery Destruction Function

⚠️ WARNING: The battery destruction function is intended for safely draining batteries prior to disposal. It should NOT be used for batteries in normal use, as it can cause irreversible damage. This function completely drains the battery's voltage, preventing the risk of combustion due to residual voltage after discarding.

6. Maintenance

  • Keep the charger clean and free from dust and debris. Use a soft, dry cloth for cleaning.
  • Store the charger in a cool, dry place away from direct sunlight and extreme temperatures.
  • Regularly check all cables and connectors for signs of wear or damage. Replace any damaged components immediately.
  • Ensure proper ventilation around the charger during operation to prevent overheating.

7. Troubleshooting

  • Charger not powering on: Ensure the DC input voltage is within the 10.0V-49.0V range and polarity is correct. Check power supply connection.
  • Charging error message: Verify the selected battery type and cell count match the connected battery. Check battery health and connections.
  • Overheating: Ensure cooling fans are unobstructed and operating. Reduce charging current if necessary.
  • Crackling sound from voice messages: If the voice messages have poor quality, you can lower the volume or turn off the sound in the system settings.
  • Screen squeaks when tilting: For typical tilting angles (40-60 degrees), this should not be an issue. Avoid forcing the screen beyond its comfortable range to prevent potential damage to the hinge mechanism.
  • Inaccurate voltage readings: Use the manual voltage calibration function in system settings to adjust the charger's readings to match a known accurate voltmeter.
  • Battery not balancing: Ensure the balance port is connected for lithium batteries.
  • Charger failure during discharge: Always supervise charging and discharging. If any unusual behavior (e.g., smoke, fire) occurs, immediately disconnect power and take appropriate safety measures. Ensure all battery and charger settings are correct and within safe limits for your specific battery type.

8. Specifications

Feature Specification
Input VoltageDC 10.0-49.0V @MAX60A
Supported Battery TypesLiPo, LiHV, LiFe, Lion LTO (1-8S); NiMh (1-20S); Pb (1-15S)
Balance Current2000mA @2-8S
Accuracy<0.005V
Charge Power0.1-30.0A@800W*2 ASYN, 0.1-50.0A@1600W*2 SYNC
Discharge Power0.1-30.0A@800W*2 Recycle, 0.1-10A@40W*2 Normal
USB OutputUSB-C 20V@65W (PD, QC, AFC, FCP, SCP, PE, SFCP, VOC)
Battery Voltage Range1.0V-5.0V @1-8S
Battery Internal Resistance1-100mR @1-8S
DisplayIPS 3.5 inch, 480*320 Pixel, Capacitive Touch
Product Dimensions130mm*97mm*42mm
Product Weight450g
MaterialPlastic (ABS)
CertificationsCE, FCC, RoHS
Recommended Age14+y

9. User Tips

  • The M8D is a compact, powerful, and modern charger supporting up to 8S batteries, performing as expected.
  • Consider updating the firmware to the latest version (e.g., 3.11) for new features like RC discharger regeneration station compatibility.
  • The charger collects very detailed data, which can be useful for monitoring battery performance.
  • The screen size, while functional, might be considered small by some users.

10. Warranty and Support

For detailed warranty information, technical support, and service inquiries, please refer to the official ToolkitRC website (www.toolkitrc.com) or the comprehensive PDF user manual.

ToolkitRC Technology (Shenzhen) Co., Ltd. provides support for this product.

11. Compliance

⚠ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

© ToolkitRC 2024. All rights reserved.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.